Question about 2003 Jaguar X-Type

1 Answer

No clutch replace clutch plate and bearing have good pedal pressure but car wont shft plate sent by dealer looks nothing like old one

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

This could be the wrong clutch also check your clutch mastr cylinder and slave cylinder

Posted on Nov 07, 2012

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 13 Answers

SOURCE: 1994 Jaguar XJS CLUTCH

hi mate cet the number for gmf car spares they will help general motor factors

Posted on Jun 12, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi i just put a new master cylinder a month back now today my clutch felt hard and when i put it in reverse heard a broken sound clutch went flat and oil came from the master what can the problem be


Umm...

A mechanical 'breaking noise' doesn't sound good. It's hard to diagnose a problem online without being there to see/hear the vehicle. But .. it may be that your clutch pressure plate has broken/ release/throwout bearing has broken?

It's difficult to see why the master cylinder should leak - unless it was incorrectly fitted in the first place?

Just to check ... The master cylinder is in the engine bay/compartment and is where you top up with clutch fluid. When a master cylinder fails it usually results in no pressure at the clutch pedal, not a leak.

The clutch slave cylinder is the one that does all the work. When you press the pedal hydraulic pressure is sent from the master cylinder to the slave cylinder - which then pushes the release/throwout bearing against the clutch pressure plate and 'disconnects' the driven plate .. allowing you to change gear.

The slave cylinder is the one that does all the hard work - it is located somewhere where engine and gearbox mate together, usually at the bottom right/left. It's usually the one that fails/leaks. It's quite easy to replace..

I don't think it is anything to do with reverse gear. It's more to do with the clutch pedal being depressed - and, I would suspect - something has failed.

The link below is generic images of a clutch:
clutch diagram Google Search

Basically, a clutch is 3 parts. There's the 'pressure plate' which bolts onto your flywheel. The pressure plate is a 'spring'. You depress the clutch pedal and the release/throwout bearing presses onto the centre of the pressure plate causing the 'fingers' - the springs - to bend back and take pressure off the driven plate - which is the link - the drive - between engine and gearbox.

If you have a leak your clutch will not work. This causes a 'grinding/crashing' noise when you try to change gear. The first thing you should do is check where the leak is coming from and do something about it.

The 'noise' that you mention may be due to the fact that the gears are 'grinding' as they try to mesh together without the use of the clutch.

The first thing you should do is check why there's a leak. It's difficult to see why a new master cylinder is leaking unless it was incorrectly fitted and damaged (pipes incorrectly connected..).

If it's the slave cylinder that is leaking - replace it. Easy job.

If Master cylinder and slave cylinder are ok - you have to look at your clutch unit. A clutch is always replaced with 3 parts ... throwout bearing/pressure plate and driven disk.

May 04, 2016 | Cars & Trucks

2 Answers

When i press the clutch pedal down it makes a rubbing noise similar to worn brake pads.stuart


opel vectra ,,,,ot sure if their is a automatic adjustment on the pedal ,if so it could be this failing which the cable could be frayed ,would really need to see it to know for sure

Feb 08, 2016 | Opel Vectra Cars & Trucks

1 Answer

1986 isuzu trooper clutch pedal went soft


some of these were manual clutch cable check adjustment of cable at firewall (bulkhead) and check for cracks around where cable goes through to inside cab common on old girls.
if hydraulic clutch system
check fluid in clutch master cylinder is it low?
it could have leaking slave cylinder on gear box bell housing or your clutch needs replacing, gear box out and replace clutch as a kit, pressure plate, clutch plate, thrust bearing (comes as kit) but dont forget to check and or replace the spigot bearing in the rear of the crank shaft when doing clutch kit.

Apr 01, 2014 | 1986 Isuzu Trooper

1 Answer

Manuel trans shifter tough too shift


if you getting a good pressure from the clutch pedal, change out the shifter bushing, that will help some. if you get a poor pressure from the clutch pedal, pressure plate has weaken, need to change out you pressure plate, throw out bearing, since your in the clutch system i would change out the pad also. Old vehicle and high miles, heavy trucks, its common. also check the slave cylinder, make sure it good working operations. worn rubber seal inside slave cylinder will cause a blow-by when press down the pedal therefore, causing to have a weak clutch pedal and hard to shift/engage into gear, same way goes for weak pressure plate. Good luck!!

Nov 09, 2011 | 1994 Isuzu Rodeo

1 Answer

I drive a 2004 Ford bantam. The clutch all of a sudden started shuddering. It was fine and the nxt moment it felt like the clutch pedal became 'sticky'. After that the clutch started shuddering. I...


the clutch disc probably finally gave up,, replace it,, have the pressure plate surfaced if needed,check the fingers for any wear , if they have any replace this part .. replace the throw out bearing,, and your good to go

Oct 01, 2011 | Ford Cars & Trucks

1 Answer

Car wont go into gear when the car is running but will if the car is off and i just had the cluch replaced


Do you have pressure from the clutch assemble,or clutch pedal. if you do then the problem is the installation of the clutch,we know trans axle is good because you can put it in gear with the engine off the problem will be a clutch plate assemble. and the slide bearing release fork, the clutch pressure plate are the connecting link between the engine and trans axle,when you release the clutch the disk and plate joins the engine and trans axle togeter.when the car is runing the transaxle synchronizer will not let you go in gear. but when engine is off the pressure plate is non operational and the T.O bearing . Your fix is a Prssure Plate. (your basically slipping)

Apr 27, 2011 | 1998 Saturn SL

1 Answer

Renult megane o3-19-DCI Replacing clutch plate dont know which side to presure plate.


Hi,
look at the clutch plate centre hub. The side which fits to the pressure plate is generally raised further than the side which fits to the flywheel side if you have the old pressure plate and clutch plate, look at the pattern on the clutch plate, it will be emulated on the pressure plate..

Hope that you have had the flywheel 'skimmed' to ensure good contact with the clutch plate. It would be a good thing to also check the spigot or nose bearing / bushing in the flywheel. All should be replaced as a set, pressure plate, spigot bearing,clutch plate, release / throwout bearing and the flywheel skimmed.or replaced if necessary.

Happy motoring.

Feb 01, 2011 | 2003 Renault 181

1 Answer

Getting harder and harder to place into gear. Also, when the clutch is disengaged (pedal down), I will hear a louder noise, sounds like something is rubbing on something


It seems like the clutch pressure plate has gone, not releasing the clutch plate once the pedal is operated.
The noise you hear, is it a screeching one or is it like the gears rubbing eachother.
If its a screeching noise thn its the release bearing and if its a heavier grinding noise thn its the gears.
Guess you will have to replace the clutch pressure plate, its highly recomended though to replace the pro-kit,i.e the clutch plate, pressure plate and the release bearing.
Good luck.

Jul 08, 2009 | 1991 Isuzu Rodeo

2 Answers

Manual clutch


Sounds like the wrong pressure plate. I got a kit from Autozone and it was the wrong pressure plate. My old one was obviously thicker. With the new pressure plate, the shift fork was almost at full travel before any resistance. That's no good. I had to pull the transmisssion again and use my old pressure plate. Luckily, it was in good condition. Then, the clutch slack was easily adjusted and works great.

Jun 07, 2008 | 1992 Isuzu Pickup

Not finding what you are looking for?
2003 Jaguar X-Type Logo

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

yadayada
yadayada

Level 3 Expert

75744 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...