Question about 1990 Ford F250

1 Answer

Where is the inline spout connector on a 90 ford f250 with a 460

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Welcome Back:

    Visited the website for 2 consecutive days.

  • Contributor
  • 5 Answers

In the wiring run just prior to distributor where is the inline spout connector on a 90 ford f - spout.jpg

Posted on Dec 25, 2012

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

jonbrown725
  • 73 Answers

SOURCE: 1987 Ford F-150 stuck at base timing. SPOUT connector inoperative

In one case I have seen the spout plug was bad.

Posted on Jan 14, 2009

fordfixer
  • 58 Answers

SOURCE: I can't find the inline spout connector.

Taurus X does not have a spout connector.

Posted on Feb 28, 2010

  • 335 Answers

SOURCE: 93 ford f250 only fires

Check/replace your ignition module.

Posted on Mar 22, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

89 chevy blazer spout connector located


Only Ford products used a spout connector during the 1980s and 1990s.

May 17, 2013 | Chevrolet Cars & Trucks

1 Answer

WHERE IS THE INLINE SPOUT CONNECTOR


right between the front of the battery and the rear of the driver side headlight under the wiring harness that goes to your ignition control module. It is pretty well hidden...

May 19, 2012 | 1995 Ford Explorer

1 Answer

Show spout connector location 1989 ford f250 xlt


if you look on the distributor you will see the large connector for the mudule bolted to the side. The spout connector will be within inches of the module connector.

Feb 06, 2012 | Ford F-250 Cars & Trucks

1 Answer

Need to know what electric connecter to dissconnct before setting timing


Okay locate the distributor and look for a single inline spout coming out of wiring harness to distributor, unplug the connector end , this is like a cap, remove it and set timing then reconnect it,this is located right next to distributor.good day

Aug 17, 2011 | 1988 Ford Taurus

1 Answer

I just put a new head in my 1987 2.3 4 cylinder ford ranger, the timing is good but i didnt disconnect the spout. what should i do


10 DegreesBefore top dead center*Base timing specification*Set at warm idle speed (electronically controlled - not adjustable)*Disconnect single wire spout connector (yellow/light green) or remove shorting bar on double wire spout connector at ignition module (terminal #5)*All accessories off*Transmission in neutral (parking brake engaged)

Apr 30, 2011 | 1990 Ford F150

1 Answer

What is an incline spout connection. Its supposed to have something to do with the timing on a 1989 ford Ranger xlt ,2.8 dual 4 Cycinder extended cab


The "Inline Spout Connector" is used to control the engine timing by dis-connecting the timing control from the timing control unit, and you must remove the inline spout connector before you can change or set the ignition timing, and if the inline spout connector is missing, then the engine timing will not be controlled by the dura-spark control unit, the check engine light should be on, and the engine will perform poorly. Usually it is located out by the distributor or over by the dura spark control unit.

It is normally a small squared looking grey plastic thing that should be in the end of a wire connector, and that is the only thing that will on the end of that wire connector, and it is basically just a jumper plug. Here is a similar image of what you should be looking for.




80b25a8.jpg

Jun 05, 2010 | 1989 Ford Ranger

1 Answer

I can't find the inline spout connector.


Taurus X does not have a spout connector.

Feb 27, 2010 | Ford Taurus X Cars & Trucks

1 Answer

1996 Ford F-150 300 inline 6 timing gears/timing issue


u have to unplug the spout small gray plug on driver side in the eng comp . on the fender wall on plug that set timming thing it should b 10 deg b4 top dead center then plug spout back in comp will adv timming

May 31, 2009 | 1993 Ford F150 SuperCab

1 Answer

Picture location of spout on 88 ford crown 302 fuel inj


the spout connector should be in the harness at the distributor

May 02, 2009 | 1988 Ford Crown Victoria

1 Answer

1987 Ford F-150 stuck at base timing. SPOUT connector inoperative


In one case I have seen the spout plug was bad.

Dec 07, 2008 | 1987 Ford F 150

Not finding what you are looking for?
1990 Ford F250 Logo

Related Topics:

195 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...