Question about Cars & Trucks

1 Answer

Have no compression in cylander 5 - Cars & Trucks

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

New motor or rebuild it

Posted on Nov 06, 2012


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

2001 cherokee # 5 misfire..switched spart plug with another cylander still # 5 changed coil and injector didnt fix problem..HELP

Did you put a "noid" light on the injector connector to ensure it's getting the pulse to open? Do you know that you are getting spark at the plug? The HV could be leaking out of the cable or connector(s). Finally, if all that's good you may need to do a compression test.

Jan 03, 2015 | 2001 Jeep Cherokee

1 Answer

1996 volvo 850 missfire cylander 4

If this has the coil over the spark plug try replacing the coil. If it still has wires replace the cap, rotor and wires. Do a compression test and check for a mechanical problem like a burnt valve.

May 08, 2014 | 1996 Volvo 850

1 Answer

No compression on one cylander 1998 sonata

what about the plug and wire for that cylinder?

Mar 30, 2014 | Hyundai Motor 1998 Sonata

1 Answer

Mising firing 0n one cylander

Best to begin with a 'scan/ck parameters'.....
Possible spark issue (ignition)
Possible Fuel Injector Issue
Possible mechanical issue (compression ??)

Mar 01, 2014 | 2000 Ford Mustang

1 Answer

Hydraulic lifters

Pull #7 spark plug perform a cold compression test, then perform a hot compression test. What were your reading?

Feb 10, 2014 | Dodge Ram 1500 Cars & Trucks

1 Answer

Water in all cylanders

Sounds familiar. If the engine oil is too full, oil will splash into the spark plug openings. Then, condensation will sit on the oil shorting the plugs. Be sure not to overfill. Also, the valve cover gasket has an inside seal. Once again, oil will partly fill the spark plug hole if the gasket is bad. There is a large hole in back of the valve cover leading right to the plugs. Be careful not to rinse the engine. Gaskets seal the plugs but water can sit on the plug openings.

Dec 26, 2013 | 2000 Kia Sportage

1 Answer

Car wont start

There are only 3things that cause a car not to must narrow it down to 1 no fuel getting to engine, 2 low compression to cylanders"sp" .3 no spark to the plugs.

Dec 25, 2013 | 1994 Pontiac Firebird

1 Answer

Hello my car 2001 ford tauus problem is cylander N1 not working

If cylinder #1 is not firing, first run a compression test. If compression is low (less than approx 70 P.S.I.), you have internal problems. If it,s good, (same or close to other cylinders), check your plug or wire, if those are good, check for vacuum leak at runner.

Jan 10, 2011 | 2001 Ford Taurus

1 Answer

#4 cylander is misfiriing where is the # 4 cylander located on a 2002 Ford escape 6cyl. 4x4

Middle cylinder on firewall side of engine. Front is 1-3-5, firewall side is 2-4-6 from front of engine.

Apr 25, 2010 | 2001 Ford Escape

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

79024 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

13652 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides