Question about Cars & Trucks

1 Answer

C93 c1500 starts off in second gear and dont shift to next gears,reverse works fine

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 153 Answers

Transmission module that shifts the transmission.
Automatic Transmission Control Solenoid Double check with auto parts store.

I hope this helps!

Posted on Nov 07, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
chrischronic
  • 235 Answers

SOURCE: 1995 crown vic gear problems/gear shift wont lock

if the shifter is loose and sloppy feeling then the shift cable bracket has come loose under the dash at the steering wheel. remove the lower panel under the steering wheel so you can see under the dash then get flash light and look while jiggling the shifter. you should be able to see the cable and bracket. if the bracket is loose then tighten the bolts. note this bracket is at the steering colum.

Posted on Jan 22, 2009

emissionwiz
  • 76630 Answers

SOURCE: Reverse gear on 1988 Chevy C1500 automatic transmission

sounds like the reverse clutch is shot, pull the pan and look for allot of grey material in the pan, some is normal but a big pile is trouble, if it is not to bad change the fluid and filter and use the new DEXRON 6 fluid, it is compatable with all GM automatics, keep your fingers crossed and it should give you a little while longer before u need an overhaul..

Posted on Mar 08, 2009

wwjdcgh
  • 114 Answers

SOURCE: automatic 3 speed transmission wont shift out of first gear

that is what they consider safe mode for those transmissions, they are a very smart electronic transmission it does that so you dont ruin the trans.
It has detected a problem and you must take it to a tech and have the codes pulled, could be as simple as a sensor or solenoid pack

Posted on Mar 09, 2009

dr_greg
  • 192 Answers

SOURCE: cannot shift into reverse although forward gears all functional

have ur shift linkage bushings replaced....most likely thse are torn or completely broken .. this is common on these models..also on some vw's of the same years

Posted on Apr 10, 2009

carlsbiz
  • 1124 Answers

SOURCE: 1st gear slipping at start. reverse and other

Have you checked the trani fluid ?
It could be slipping just enough to notice in 1st gear beause that is the most resistance..
A slip is a slip..
Or it could be that the bands are warn in only first gear - wich would cause damage before long..
Some shops give free estimates..

Posted on Jul 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Suzuki Forenza error code P0782


Well code 782 is for a problem with the 2-3 shift solenoid or the circuit back to the engine computer. The solenoid is inside the transmission.
Code 722 was for a problem with the speed sensor. You could have a wiring harness problem.

Jan 22, 2014 | 2004 Suzuki Forenza

1 Answer

AutomaticTransmission wont shift


The governor gear may have stripped,it's plactic.
Just in front of the tailshaft there is a round cover about 4 inches around,
some have a wire clip over the cover.
Pop the cover off,(might lose about 1/2 cup of fluid)
Pull the governor out (should be very easy)
If the plastic gear on the end is "apple cored" or at all damaged ,
it will keep the ****** in low.As will having no vacuum to the modulator valve.

Mar 12, 2012 | 1991 Chevrolet C1500

1 Answer

1997 Saturn SC1 | manual transmission not going into first or second.


when was the clutch last change ?
my saturn is a 1998 with over 300k and never had this happen but I have changed my clutch at 275k

Mar 12, 2017 | Saturn SC Cars & Trucks

1 Answer

My transmission slips going through second gear if i get my foot in it just a little bit, and it doesnt always go into reverse. if i shift into reverse and it doesnt shift, i have to shift to neutral then...


this problem is a common failure associated with your shift solenoinds inside your tranny. of course a shop is not gonna tell you this because by the time you wanna get it repaired it is usually too late and have already cause damage to your clutch pack and internal parts, thats the main reason why a shop wont mess with just replacing your shift solenoid (aka valve bodie)

Feb 18, 2010 | 2000 Chevrolet Silverado 1500

1 Answer

4l60e going from 1st to 3rd and dont have overdrive any more


You most likely have a broken sunshell inside the transmission. They tend to go out when the transmission is shifted to drive when while still rolling in reverse.

Dec 28, 2009 | 1994 Chevrolet C1500

1 Answer

My avalanche won't shift


Sounds like a broken internal trany part. Take it out and shift it through the gears manually to see which gears work and where it revs up. The second and fourth gears are the ones that tend to not work.

Oct 11, 2009 | Chevrolet Avalanche Cars & Trucks

1 Answer

All forward gears work and shift fine....all the sudden no reverse, still drove forwards and shifed fine. Reverse is like park or neutral.


There is a pin in the transmission that has sheared off or a band has come loose. Bottom line you need to have the transmission serviced and repaired.

Sep 01, 2009 | 1991 GMC C1500

1 Answer

1992 k1500...no reverse


the hose is a vent and hangs there away from the converter. If reverse is gone, it is a internal problem. If all gears forward are there, then the low/rev clutch pack is burned up (likely). If missing 2nd and 4th and rev, then the shell is stripped or broken

Apr 05, 2009 | 1992 Chevrolet C1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...