Question about Rover Cars & Trucks

Open Question

Wiring diagram rover 75 1.8t crank sensor

My crank sensor wire snapped so i dont know which colour goes to what number on the actual sensor

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1861 Answers

SOURCE: tow hitch wiring diagram

Send me your e-mail address, and I will send you a .pdf of the entire rear lighting wiring;
FixYa is not set up to post .pdfs yet.
Glad to help, and thanks for choosing FixYa.

Posted on Nov 03, 2008

  • 335 Answers

SOURCE: need buick century egr diagram

If your car runs bad with an EGR code then I would suggest that the EGR valve be replaced. I would like to know what code was set on your computer. It would help greatly. When the EGR malfunctions, you will have rough idle and possible stalling. If you have a code indicating EGR it may also condem the cat converter.Please show any codes that are set. Thanks Moe

Posted on Apr 24, 2009

  • 88 Answers

SOURCE: Land rover Defender 90 cigarette lighter install

should only be a black for earth and red or yellow for power if u already have wired up to a powr source just connect to back of lighter if you dont ground the black wire to the mwal part of the car usually under a screw under the dash will do and run a red wire to 10a fuse in fuse box thats the easiest way

Posted on Jun 06, 2009

  • 12 Answers

SOURCE: I REQUIRE A WIRING DIAGRAM FOR THE TD4 ENGINE

haynes.co.uk have excellent workshop manuals with all the wiring diagrams and exploded views. I've owned a haynes manual for every single car or bike i've had so far. They will help you a lot.

Posted on Jun 12, 2009

valiantma595
  • 176 Answers

SOURCE: I am trying to wire a towbar on a 2004 Mercedes E

If you want to wire a towbar, I'd say, you can't wire a towbar, as a towbar is meant to be used to pull trailers, right? But, had you said I am trying to fit and wire a car trailer socket for my 2004 Mercedes E Class so I can plug a trailer plug for the trailer's taillights, etc. I would have understood what your needs are. Now, to fit and wire a socket to your Mercedes you need an testing tool costing less than UD$10.00. This tool it like a small screwdriver with a tip almost like a neddle and is used to punch into live sheaths of wires to see which wire is conducting (has power). This small tool is usually of plastic contruction and has a removable cap at the other end and has a length of wire with a small aligator clip at the other end of the wire. This aligator clip is clamped on a negative ( - ) surface, such as any exposed bolts or metal part of the engine or body of your car. The cap of this tool can also be unscrewed
to replace the small 12V light if it ever blows (fuses out). The overall reason of this tool is to be used to very carefully (and I mean it) pierce into any sheathed wires the check if any current is present when a particular action is being performed. The tool can be purchased at any reputable speed shop. Now, to begin with wire finding and assembly of the socket you need to first locate the braided (wrapped in a plastic tape) cable at the back part of the car, usually as close to the rear body (boot). After finding this cable (it has all the wires that control the tail lights, brake lights and reversing lights wrapped into 1 bundle), you now have to prepare a similar length of braided or prepacked cable that has wires inside expecially designed and coloured for use with most cars. In this care, if your Mercedes has different color wires, do not worry about it because you can mark them with a texta or special sticky take and write on them the different colors so that you wont become confused. Note that most speed shops sell rolls of cable specially for wiring car trailers. Just purchase a short length, depending on your requirements, unless you are to wire the whole trailer, I will discuss the objective of fitting and wiring the car with a trailer socket. Next, you may have to drill a hole where you want the cable to exit near the towbar (closest to the towball) and then you may have to decide where to screw the socket on the car, either on the lower part of its body or on a already welded plate especially fitted for the purpose of fitting a socket. This plate is usually closest to the towball. Now, lets start using the special tool to detect the current and noting down which wire is for brakes, tail light, reverse, etc. Go into the boot and locate the bundled cable. If it has a sheath, carefully cut it open and expose the 5 or 6 wires, depending on what country you are, each is different. Once you cut the sheath about 4 inches or more and have exposed the wires, try and separate them a little apart so you can work on them one by one. Now, here you need a helper to turn the parkers (lights) on, press the brake pedal to activate the brake lights, turn the ignition on but do not start the engine and put the gear selector into reverse (automatic or not), etc. Next, remove 2 or so inches of sheath from the purchased cable, spread the 5 or 6 wires apart and... if you have a wire stripper, so much the better, otherwise use a knife, being carefully not to cut or strip the copper strands in each wire. If you do, you'll have to start again. So be careful. if strands are not broken or snapped, you'll get full power to the trailer lights. If they're stripped or cut, the wires may get hot and probably cook themselves out at the point where the strands are missing. Remember, all strands must be twisted before use. Now put this aside for a moment and, with a helper to give you a hand for a few minutes, you first ask him/her to turn the lights on, then punch each exposed wires from the sheathed cable you found in the boot of your car and, with the poined part of this tool note which one has the current or power flowing that turn the car's tail lights on. Note the colour of this wire. You have a choice that you either strip this cable right away and then connect the twisted exposed copper wire, apply a solder with a soldering iron or make a good twist around the exposed wire in the boot that has the current flowing, mark this as (eg, Orange - tail lights) tail lights and then tape it with black automotive plastic tape, or you have the other choice that you puch all of the wires, locate their currents and which color is which for the following lights. I'd stick with the first option if I was you. So, next, ask your helper to depress the brake pedal and then again punch the sharp tip of the tool into the sheath of any of the other remaining wires (in the car boot that is) untill you locate the wire that has current to the brake lights. Once located (it is usually red colored), carefully strip it about half an inch and then bind the red wire from the purchased cable and either you solder it or you make sure it is a good wrap-around wirework and then wrap around this one as well with automotive insulating tape.
Repeat the process with finding the reversing lights wire in the boot by punching on the sheathed wire, carefully strip it, note the color and then bind around it a stripped and twisted wire from the purchased cable that has the same color, solder it if you have a solder. if not make sure the connection are wrapped around and tight, then tape the connection. After you've done all the wires (whatever wire is leftin the purchased cable, you either leave it unconnected or pull it out of the sheath and discard. Remember that there is usually a black wire running along into the mercedes sheathed cable. This wire should be considered as an Earth, or negative ( - ) wire. It should be also used because sometimes there is poor conduct between the car and trailer. Having this black, or negative wire connected as well will make sure you wont have a failure in connection with the car's electricity to that of your trailer. Usually, after turning the parking lights on or applying the brakes to activate the tail lights and this black wire doesn't have any current (the light on the tool does not come on after you have been punching every wire in the boot cable), it demonstrates that the black wire is negative. Now, after you have linked all the wires to that of the car wires and have insulated each of them, bend the purchased cable sideways with the car cable and retape it for a final insulation and to make sure the purchased cable stays bonded with the car cable. Pass the purchased cable through a small hole that is large enough to pass the cable but the right size to fit a grommet to seal out any dust. Now, after you have decided where you want to fit the socket, you now have to also decide if you want a round 5 pin socket or a flat 7 pin socket. Again, depending on your needs and use, I would recommend a 5 pin socket. Okay, having written down the colors of the wires used for parking lights/headlights, tail lights, reverse lights, left right indicators signals, etc., you now have to wire the socket before ataching it yo the body of your car or the plate of the towbar. Please take your time studying the wiring connection instructions that came with the socket packaging or box. Once wired, have your helper help you with turning the lights on, pressing the brake petal, turn the ignition on but don't start the engine and put the gearshift into reverse, turn the left or right signals. You can test all this by either clipping the aligator clip to an exposed chassis or clamp the clip directly behind the socket and on the black negative wire ( - ) then touch the socket pins with the pointed tip of the tool. If the tool's light comes on as each pin is touched and it is the correct sequence as per wiring instructions that came with the package and everything works accordingly, you can now install the socket to the car body or towbar plate. Now, you also have to make sure that the plug on the trailer is also wired accordingly to the pins of the socket on the car by orientating and checking if the pin that is for, say braking, is also the braking pin on the trailer plug. If this is too much for you, an automotive electrician is a better option because all you need do is make mistake and you'll cook your car's wiring.
Thank you. Michael. Automotive mechanic since 1973.

Posted on Sep 27, 2009

Testimonial: "Thank you, I have the tool to do the job and i am an electrical engineer (not a Cook) by trade so i understand the importance of getting it right."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to wire a range rover power seat


There are 4 electric motors under each seat and a 5th inside the back rest. Also under each seat is a module containing the relay and memory module It is possible to run new wires but the job will be much simpler if you have (or can get) a pair of original wiring harnesses to go between the module and the harness behind the centre console (remove ashtray, lighter and storage bin) Spade terminals can be used if the module is missing. Make sure the wiring colours all match.

Of course, this is a simplified explanation. Go to Rovers.net for more detail

Jul 29, 2014 | 2002 Land Rover Range Rover

1 Answer

2000 ford taurus crank sensor wiring diagram


follow this link and take your pick of many diagrams for the crank sensor.

http://images.search.yahoo.com/search/images?_adv_prop=image&fr=yfp-t-900&va=2000+ford+taurus+crank+sensor+wiring+diagram

Apr 05, 2013 | 2000 Ford Taurus

1 Answer

02 sensors wiring


The yellow and white wires take any white wire.I dont now why they dont tell you that.And just fit black to black and grey to grey that simple good luck pippall.

Aug 08, 2009 | 1996 Jaguar Xj Series

1 Answer

Jeep wont start after i replaced crank pos. sensor


two things to check first there is an adjustment on that sensor small piece of paper on end of sensor has to contact fly wheel and be torn off at start up adjust to just touch flywheel should do the trick.second is the connector snapped tight. and the wires on those motors are know to have problems just un hook sensor and disconnect battery cable and use a self powered cheap conuity tester on both wires to pcm . u dont need a diagram for this test because the tester will find the wires at pcm if there ok. if you find a open wire open the harness and follow the wire to pcm keep checking along the way with cheap tester dont use a test light ask for connuity tester. hope this helps.it may also need to be resncyed with cam sensor.

Jun 23, 2009 | 1998 Jeep Wrangler

1 Answer

Land rover Defender 90 cigarette lighter install


should only be a black for earth and red or yellow for power if u already have wired up to a powr source just connect to back of lighter if you dont ground the black wire to the mwal part of the car usually under a screw under the dash will do and run a red wire to 10a fuse in fuse box thats the easiest way

Jun 06, 2009 | 1993 Land Rover Defender

1 Answer

98 bonneville no start


The anti-theft system has nothing to do with spark . When it won't start check for B+ voltage at the ignition module . pin P a pink wire . Check pin K for a good ground . Check the 18X & 3X crank sensor signals to the PCM . It's good you have a snap on scan tool an can check sensor data , but to check cam an crank signal's you really need a scope ! Does your snap on tool have a lab scope ( oscilloscope ) Do you know what this is ?
How to test crank sensor on GM 3800 engine 3x and 18x signals

Do you have access to wiring diagrams ? Check electrical distribution in an out of the ignition switch .Free wiring diagrams here
http://www.bbbind.com/free_tsb.html Enter vehicle info Year , make , model and engine size . Under system click on electrical distribution , then under subsystem click on power distribution . Click the search button , then the blue link ! I wouldn't think the ignition switch being the problem but you never know without testing ! Do you know how to do automotive electrical testing with a DVOM - digital volt ohm meter ? Using a wiring diagram to pin point areas for testing ?
Electric Testing Techniques You Need to Know
TSB'S that GM may have on this car. For what ?

May 23, 2017 | 1998 Pontiac Bonneville

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Rover Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14333 Answers

Rob
Rob

Level 2 Expert

62 Answers

Are you a Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...