Question about 1999 Ford Escort
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: serpentine belt installation
/* Style Definitions */
mso-padding-alt:0in 5.4pt 0in 5.4pt;
font-family:"Times New Roman";
1 To replace a worn belt, locate the idler or generator
2 Loosen the hold-down fastener for the idler or generator pulley.
3 Pry the idler or generator pulley inward to release the belt tension and remove the belt.
4 Match the old belt up for size with the new replacement belt.
5 Observe the belt routing diagram in the engine compartment.
6 Install the new belt over each of the drive pulleys. Often the manufacturer recommends a sequence for feeding the belt around the pulleys.
7 Pry out the idler or generator pulley to put tension on the belt.
8 Pry out the idler or generator pulley to put tension on the belt.
9 Install the belt squarely in the grooves of each pulley.
10 Before adjusting belt tension, check for proper pulley alignment. This is especially critical with serpentine belts. Measure the belt deflection in its longest span. If a belt tension gauge is available, use it and compare the tension to specifications.
”If a belt is too tight, wear to bearings for the water pump, alternator, and engine crankshaft can result.”
11 Pry the idler or generator pulley to adjust the belt to specifications.
12 Tighten the idler or generator pulley fastener.
13 Start the engine and check the belt for proper operation.
Posted on Jan 10, 2009
Get an ALLDATAdiy.com account. trust me i did it and its the only good repair manual for this car. I have a 2003 ford zx2.
Posted on Aug 10, 2009
On level ground, jack up the front of the car and support it with axle stands.
Get an open container that will take more than 5 ltrs.
Under the engine block you will find the sump.
On the sump you should find a 13mm nut, this is the drain plug.
Undo the drain plug and have the empty container directly below the sump plug.
Retain the sump plug and clean it with a rag.
When the oil has drained out of the sump, put back the plug making sure the washer is in good condition and the plug is tight.
Now unscrew the oil filter having the old oil container below the filter housing to catch any oil.
Wipe around the the filter housing to remove any and all old oil.
Now offer up the new oil filter but do not tighten.
If the new filter fits the oil filter housing, then remove it and lightly oil the rubber seal on the filter with clean oil.
Now refit the filter and tighten it up. Not too tight, you can do this by hand but get it as tight as you can.
Now lower the car to to the ground.
At the top of the engine you will find an oil filler cap. Undo this cap.
Now put in the new oil to just below the full mark on the dip stick. Let the oil drain through the engine to the sump for a couple of minutes before checking the oil level.
If the level is between 1/2 and full, replace the filler cap and start the engine.
Now look at the oil filter and the sump plug for any leaks. Also check around the oil filler cap for oil leaks and spillage.
With the engine turned off. Clean any oil spillages and tighten up the oil filter, sump and oil filler cap as required.
Now leave the oil to drain back to the sump for a few minutes.
Check the oil level and top up as required.
I find that it is best to top the oil up to just below the Max mark.
This should solve the problem.
Posted on Aug 28, 2009
SOURCE: belt routing diagram 98 zx2 2.0
1) Start with the alternator.
2) Forward to the smooth idler
3) Forward to power steering
4) Down to A/C compressor
5) Back to crank pulley
6) Forward around tensioner
7) Back glancing off of water pump
8) Back glancing off of ribbed idler
9) Up around alternator (where you started)
Posted on Sep 11, 2009
Tips for a great answer:
Dec 21, 2015 | Ford Cars & Trucks
on Apr 15, 2015 | Ford Escort Cars & Trucks
Apr 15, 2010 | 1998 Ford Escort
Dec 20, 2009 | 1998 Ford Escort
Aug 08, 2009 | 1998 Ford Escort
Mar 30, 2009 | 1998 Ford Escort
Mar 28, 2009 | 2001 Ford Escort ZX2
Jan 18, 2009 | 2001 Ford Escort ZX2
Dec 03, 2008 | 2001 Ford Escort ZX2
54 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: