Question about Cars & Trucks

1 Answer

Can i paint over plastic wall panels

I have plastic panels on my kitchen walls can i paint over them instead of pulling them off

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 4 Answers

Yes they sell a paint for plastic. you can also use a liquid sander to rub on it first and then texture and paint

Posted on Nov 06, 2012

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 4044 Answers

SOURCE: I am looking for a replacement for the plastic

You'll need to look for that at the dealer or at a Junk Yard.

Posted on Jul 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Peeling paint on cinderblock walls in basement


Just a guess, but it is likely that moisture is causing the paint to peel. I suggest you remove as much peeling as you can with a wire brush and then use a waterproof sealant. I had very good luck with a product they sell to seal cement walls in basements with moisture problems.

Mar 09, 2015 | Cars & Trucks

1 Answer

How to remove grease splashes from emulsion painted wall


Basically you can't without affecting the Paint underneath ((
If only light splashes then a conventional kitchen cleaner will do BUT only put the cleaner on the cloth, work a small area at a time.
After doing getting it off and allowing it to dry, then use a lint free cloth, soaked in warm water to "scrub" paint from surrounding areas into damaged area but not too hard otherwise will go through the paint levels. Then allow to dry naturally ))

Nov 05, 2014 | Cars & Trucks

1 Answer

Is there too much moisture in the air to paint Dunn Edwards outside exterior paint


Hi Sheri

I trust you are well.

I would suggest you paint on a bright sunny day when the walls you want to paint are properly dry, any paint will not take well on damo walls.

Hope this helps

kind regards

Aug 15, 2014 | Cars & Trucks

1 Answer

Is there too much moisture today to paint ,dan Edwards paint the outside of a house


Hi Sheri

I trust you are well

I would suggest you paint in a dry sunny day when your walls are free from damp and moisture, all paint will take best on dry walls.

Hope this helps

Kind regards

Aug 15, 2014 | Cars & Trucks

1 Answer

I stupidly applied second coat of matt emulsion paint to interior wall above a radiator whilst radiator was still warm. Paint went thick and difficult to spread, and dried almost immediately. This left an...


My thought would be to hide it if you can with a reflective piece of polished stainless or aluminum to reflect the heat. I have run into your problem and no easy solution.

May 04, 2017 | Cars & Trucks

1 Answer

How do i clean out the internal gutters on my 2001 X5 ? after it rains there is water in the rear side panels.


This is a guess, as I am not familiar with this particular body, but try pulling up the door sills and pulling the carpet away from the side wall. Are there plastic plugs there? If so, remove the plugs and rig a hose to your vacuum cleaner that will fit through the holes.

May 20, 2011 | 2001 BMW 5 Series

1 Answer

Wher can i find the blower motor resistor on a 2001 X5


It's between center consol and fire wall .
Very tight place to work on , but not too bad to replace.
You may need to take trim (plastic panel) out to see it.Work your way from pass. side footwell and with flash light look behind midpart of consol next to the fire wall , if you have new one in hand then just compare front side of it (wire plug side) with what you see behind consol and you'll see it.
There will be another wire harness on your way to pull it out , work your way around it.
There is no bolt or nuts holding resistor , plastic leap needs to be carefully pushed away and unclip resistor.
The hardest part is to disconnect the electrical plug from resistor , the rest is easy.

Jun 16, 2010 | 2001 BMW 5 Series

1 Answer

Is there any way to fix a crack and a hole in the plastic interior wall of the CRV. Apparently, something I was transporting, like a bike pedal, punctured the side of the CRV's rear interior. The plastic...


You will need to get the panel plastic welded. You should be able to find someone to do this, should not be expensive or take lond, you can even leave panel with them so you can use your vehicle. Won't be perfect, you will only be able to tell if you look for repair, they can colour match really well.
Cheers

Apr 06, 2009 | 2002 Honda CR-V

2 Answers

Electronic Control Module Installation 1994 G20 Chevy Van


I just had the same problem. If it is a regular van try under the driver seat in a plastic box. If it is a conversion van try in a pannel just behind driver seat on side of van wall behind a pannel that looks like a vent.

Dec 28, 2008 | 1987 Chevrolet G20

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...