Question about 2000 Ford Econoline

Open Question

Remove the rear window on a ford econoline van

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

samson-1
  • 153 Answers

SOURCE: freeze plugs ford econoline 150

The freeze plugs can be fixed with the engine in the veicle. There are some rubber plugs available that have a bolt thru the middle. Pry out failed plug, push in rubber replacement, tighten bolt to expand rubber. Fixed.

Posted on Oct 25, 2008

emissionwiz
  • 75797 Answers

SOURCE: Why won't my 1992 Ford Econoline van start

I suspect the fuel pump has stopped working, check the fuel pressure or listen to the noise it makes by taking off the gas cap and listening for a humming noise when the key is turned on, this will stop after a few seconds.

Posted on Nov 07, 2008

  • 2 Answers

SOURCE: 1995 ford econoline van speedo/trans

It is either the speed sensor, the wireing in between ot the speedometer module it self. The sensor sends pulse train signal to the speedometer module and there it drives the speedometer and is divided in frequency by about 7 and feed to the computer and the cruise control. When the signal drops the Engine management computer thinks the speed is real slow and raises the transmission pressure.

In the one I had it was a cold solder jooint on the bacjk of the speedometer module itself but this was the divided output and the speedometer itself still worked. The easyest part would be the sensor that mounts on the rear axile I believe and should cost less than 30.00 dollars. If not that thebn it's the wiring or the speedometer module electronics..


Posted on Mar 25, 2009

emissionwiz
  • 75797 Answers

SOURCE: where is the speed sensor on a 1995 Ford econoline van

the sensor is located on the driver side of the transmission case

Posted on Jun 19, 2009

  • 67 Answers

SOURCE: my 1994 ford econoline van is not shifting gears

Hello.
This a repair for a transmission shop. Sounds like the pumps are bad inside the transmission. Thats the worst option I have.
It also can be a poor shift linkage adjustment. And the last solution can be the speed module that tell the transmission when to shift.
Goodluck! I hope this helps!

Posted on Dec 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the oil sensor located on a 1998 Ford Econoline Van?


my dad's Ford is left of center on rear, behind manifold.
_________________
Ford vcm ids

Oct 31, 2012 | 1998 Ford Econoline

1 Answer

HOW TO INSTALL SERPENTINE BELT ON 87 FORD VAN


For the 1987 Ford Econoline Van:
Size Engine??
Engine Options (AC/No AC)??

Click on the following direct, Free Link. It has the Serpentine Belt Diagram for your 1987 Ford Econoline Van depending on your size Engine and Engine Options.

Let me know if this helped....

http://www.2carpros.com/car_repair_information/year/1987/make/ford/model/econoline/1987_ford_econoline_drive_belt_routing_diagram.htm

Apr 14, 2010 | 1987 Ford Econoline

1 Answer

How am I able to test an Idle Air Control Valve for a 2000 Ford Econoline Universal Van E-150 5.4L?


if you go to the trouble to remove it id suggest installing a new one if the van is idling incorrectly or abnormally high it may be faulty

Jan 19, 2010 | 2000 Ford Econoline

2 Answers

Remove door panel on a Ford Van


For a 1999 Ford Econoline 150 (assume the same or very similar), remove triangular plastic cover over mirror assembly by prying straight out, remove plastic door handle cover by prying up from the front side, remove electronic door switches by prying up from back side, remove round plastic cover at bottom rear of door panel. Four screws are now revealed, remove them. Lift door panel straight up, clips are hooks (not snap in). Work door switch assembly out of door panel. Set door panel aside. Reassemble in reverse order.

May 09, 2009 | 2000 Ford Econoline

1 Answer

Computer


Ford Econoline have a computer mounted at rear door, drivers side,

with case of some nilone materials,

THNX

May 22, 2008 | 1999 Ford Econoline

Not finding what you are looking for?
2000 Ford Econoline Logo

Related Topics:

219 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...