Question about 1996 Chrysler Concorde

1 Answer

Lower a arm

How do i fix it

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 166 Answers

It's not "fix"able. Replace it. It's not that difficult. It includes the ball joint. Insist on a Moog replacement.

Don't tighten the pivot bolt (the end with the rubber bushing) until you've reassembled everything and put the car back down on its wheels. This will ensure that the bushing is locked in the neutral up/down position. If you fail to do this, the new bushing will fail quickly.

Posted on Apr 04, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace the lower ball joints on a 2000 windstar?


According to Autozone.com, you must replace the whole control arm. Here is their procedure:
NOTE do not begin the removal procedure unless a new strut-to-lower arm nut, a new ball joint pinch bolt/nut and a new lower arm-to-front subframe bolt/nut are available.

  1. Remove or disconnect the following:
    NOTE
    Do not use a hammer to separate the ball joint from the front wheel hub and spindle.



    WheelsLower arm strut nut and dished washer. Discard them.
  2. Place the steering wheel in the unlocked position.
    NOTE
    Do not allow the halfshaft to move outward. Over-extension of the halfshaft joint could result in separation of internal parts, causing failure of the halfshaft joint.
  3. Remove or disconnect the following:
    NOTE
    Use extreme care to not damage the ball joint boot seal.



    Lower arm ball joint nut and pinch bolt. Discard them.Lower arm from the front wheel knuckle



    Remove and discard the lower arm-to-front subframe bolt and nutRemove the lower arm from the vehicleTo install:
    1. Install or connect the following:

      Lower arm strut into the lower arm rear strut bushingLower arm into the front sub-frame bracketNew lower arm-to-front subframe nut and bolt. While holding the lower arm horizontal, tighten to 85-97 ft. lbs. (115-132 Nm).Ball joint stud-to-wheel hub and spindle, making sure that the ball stud groove is properly positioned.New lower arm ball joint pinch bolt and nut. Tighten to 46-52 ft. lbs. 62-71 Nm).
    2. Clean the lower arm strut threads to remove dirt and contamination.
    3. Install the dished washer with the dished side away from the lower arm rear strut bushing.
    4. Install the front suspension lower arm strut-to-strut nut and tighten to 85-97 ft. lbs. (115-142 Nm).
    5. Install the wheels.
    6. Lower the vehicle.

Jun 12, 2015 | Cars & Trucks

1 Answer

My rear lower arms are attached to a rusty frame,how do I fix?


I would go to a frame shop you may need metal added as well as alignment to the frame

Sep 04, 2012 | Jeep Cars & Trucks

1 Answer

Where is the rear suspension sensor located what does it look like


located on the lower control arm, it is fixed to the arm and the body of the car, looking from the back to the front of the car it will be noticeable black and steel in color, the sensor is up on the body and there is a metal rod that runs from it to about middle ways on the lower control arm, suggest raising the vehicle off the ground...

Sep 08, 2011 | 2000 Lincoln Continental

1 Answer

How do I. Get the lower control arm off my 01 stratus


SAFELY RAISE SUPPORT VECHICLE ON JACK STANDS. MAKE VECHICLE SITTING ON LEVEL SOLID GROUND. REMOVE FRONT WHEELS , REMOVE HEAT SHIELD, IF EQUIPPED WITH 15 INCH WHEELS, REMOVE BALL JOINT CLAMP NUT, REMOVE SWAY BAR TO CONTROL ARM BOLTS, REMOVE STRUT CLEVIS FROM THE LOWER CONTROL ARM, REMOVE SWAY BAR TO CROSSMEMBER BOLTS LOOSEN THEM AND ROTATE THE SWAY BAR AWAY FROM THE CONTROL ARM, LOWER CONTROL ARM FROM STEERING KNUCKLE. REMOVE BOTH LOWER CONTROL ARM BOLTS. REMOVE CONTROL ARM. DURING INSTALLATION TORQUE LOWER CONTROL ARM BOLTS 120 FT LBS. CONTROL ARM STEERING KNUCLE TORQUE NUT 70 FT LBS.TORQUE SWAY BAR BOLTS 21 FT LBS.

May 23, 2011 | Dodge Stratus Cars & Trucks

2 Answers

How to fix a ball joint in a ford tempo


REMOVAL & INSTALLATION The lower ball joint is integral to the lower control assembly and cannot be serviced individually. Any movement of the lower ball joint detected as a result of inspection requires replacement of the lower control arm assembly.
  1. Raise and safely support the vehicle.
  2. Remove the wheel and tire assembly.
  3. Remove the nut and bolt securing the ball joint to the steering knuckle.
  4. Remove the nut and bolt securing the control arm to the vehicle sub frame. To install:
  5. Install the control arm assembly to the vehicle sub-frame using the nut and bolt. Tighten the nut to 69-86 ft. lbs. (93-117 Nm).
  6. Install the lower ball joint into the steering knuckle and secure it with the nut and bolt. Tighten the nut to 32-43 ft. lbs. (43-59 Nm).
  7. Install the wheel and tire assembly and lower the vehicle.
  8. Road test the vehicle.
prev.gif next.gif

Nov 06, 2010 | 1990 Ford Tempo

1 Answer

How do you put in a ball joint in a 2001 sebring convertible


It depends on exactly which ball joint of the 3 per side your changing, but here are the details.

COMPRESSION LOWER ARM & LATERAL LOWER ARM ASSEMBLIES
Removal
1. Loosen compression lower arm ball joint nut. Using steering linkage puller, separate ball joint and
knuckle. Remove nut, bolts and compression lower arm assembly. Remove dust cover.
2. Remove stay. Remove shock absorber lower mounting bolt. Loosen lateral lower arm ball
joint and knuckle nut. Using steering linkage puller, separate ball joint and knuckle. Remove nut, bolt and
lateral lower arm assembly. Remove dust cover.
Inspection
Using preload socket, ensure breakaway torque for compression lower arm ball joint is 4-22 INCH lbs. (0.5-2.5
N.m) for 2000 models. On 2001 models, breakaway torque is 22-54 INCH lbs. (2.5-6.1 N.m). Ensure
breakaway torque for compression lateral lower arm ball joint is 13 INCH lbs. (1.5 N.m). Check compression
lower arm, lateral lower arm, dust covers, and bushings for damage and wear.
Installation
To install, reverse removal procedure. Use NEW ball joint nuts. Lubricate lip and inside of dust cover with
multipurpose lubricant. Using installer, install dust cover. Check front wheel alignment.
UPPER ARM ASSEMBLY
Removal
Using steering linkage puller, loosen upper arm ball joint and knuckle nut. Remove self-locking nut. Remove upper arm and upper arm shaft assembly. Remove dust cover.
Inspection
Using preload socket, ensure breakaway torque for upper arm ball joint is 3-13 INCH lbs. (0.3-1.5 N.m).
Replace upper arm assembly when measured value exceeds specification. Check upper arm, dust cover, and
bushings for damage and wear.
Installation
1. To install, reverse removal procedure. Use NEW self-locking nuts. Lubricate lip and inside of dust cover
with multipurpose lubricant. Using Ball Joint Installer (MB990800), install dust cover.
2. Ensure upper arm shaft assembly is installed at indicated angle. Verify upper arm shaft
assembly installation. Check front wheel alignment.

Once you have the correct arm off and a replacement joint (if available, some are not serviceable and require the arm to be replaced) then you will need a press or a ball joint press to change the joint. Such as
http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=38335

http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=46389

http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=66958

or http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=46967

Mar 17, 2010 | 2002 Chrysler Sebring

1 Answer

95 eagle talon broken lower control arm how do i fix?already bought new control arm.


Jack the car up and remove the tire. Use a ball joint separator on the front lower control arm and remove the remaining 2 bolts, if working on the rear lower control arm, remove the 2 bolts holding the arm in place and install the new control arm.

An alignment is recommended when changing any part of the suspension, especially control arms, tie rod ends, etc.

Nov 19, 2009 | 1995 Eagle Talon

2 Answers

How hard is it too change lower control arm bushings on 2000 toyota tundra and should i do both upper and lower at same time


ITS GOING TO BE HARD TO FIX AT HOME UNLESS YOU A PRESS AND TOOLS.YOU NEED A PRESS TO PRESS CONTROL ARM BUSHINGS IN AND OUT.

Oct 25, 2009 | Toyota Tundra Cars & Trucks

1 Answer

How to change lower ball joints


part of lower arm assembly only.

Installation
  1. Inspect lower ball joint boots and seals for damage and replace if required. Lower ball joint and seal is part of front suspension lower arm and must be replaced as an assembly.
  1. NOTE: Do not tighten the front suspension lower arm bolts and nuts to the specified torque until the end of assembly. Install nuts and tighten until snug.

    Position the front suspension lower arm in the front crossmember. Install the bolts. Install the nuts and tighten until snug.
  1. Install torsion bar. Refer to Torsion Bar in this section.
  1. Raise the front suspension lower arm to allow installation of front suspension lower arm ball joint into spindle bore.
  1. Lower front suspension lower arm with a jack while making sure lower ball joint is seated in spindle bore. Install the lower ball joint attaching nut and tighten to 113-153 Nm (82-113 lb-ft). Install a new cotter pin.
  1. Raise vehicle. Position the front shock absorber and install the nut/washer/bushing assembly. Tighten nut to 40-55 Nm (30-40 lb-ft).
  1. Install the two nuts attaching the front shock absorber to the lower control arm and tighten to 21-29 Nm (15-21 lb-ft).
  1. NOTE: Front suspension lower arms must be in the horizontal or curb position (vehicle on the ground) when tightening the front stabilizer bar link bolts. Use jackstands to raise the front suspension lower arms to the horizontal position or lower the vehicle to the ground (curb position).

    Lower the vehicle to the ground.
  1. Connect the stabilizer bar link bolt to the front suspension lower arm and tighten to 13-17 Nm (10-13 lb-ft).
  1. Tighten nuts and front suspension lower arm bolts to the No. 1 crossmember to 150-200 Nm (111-148 lb-ft).
  1. Check ride height and align as necessary. Refer to Section 04-00 .
  1. Lower the vehicle.

Apr 17, 2009 | 1996 Ford Explorer

1 Answer

Lower Control Arm


Don't bother.If the lower control arm is cracked, it is a fair bet that the strut is bent. Even if the strut is not bent, you should have the alignment checked. The force of impact on this area to crack the arm can def be connected to other areas of extreme concern.

Aug 08, 2008 | 2002 Toyota Camry

Not finding what you are looking for?
1996 Chrysler Concorde Logo

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...