Question about Cars & Trucks

1 Answer

How to install heater hose connector on a 2001 buck park avenue

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 689 Answers

Do you mean the hose clamps (Michaella)?

Posted on Nov 06, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 5 Answers

SOURCE: 1995 BUICK PARK AVENUE A/C HEATER CONTROL

its behind the glove box i just replaced it myself and im a girl!! you go girl!!!

Posted on Dec 17, 2008

  • 299 Answers

SOURCE: buick park avenue 1997 leaking need to replace

Ussualy a pain,but some radiator shops will replace it cheaper than most machanic shops.

Posted on Jun 18, 2009

  • 1986 Answers

SOURCE: How do I remove the rear door panel on my Buick Park avenue

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

SOURCE: ISUZU WAS IN AN ACCIDENT. THE PLASTIC HEATER HOSE

Strip it back and replace all the broken items/parts. New or good clean used parts. You do it or pay a repair shop. What is the problem or question. It is broken Fix it

Posted on Sep 26, 2009

wracefans24
  • 1985 Answers

SOURCE: Are Park Avenue engines compatible with La Sabre engines?

yes as long as it is also a 3.8

Posted on Jan 26, 2010

Testimonial: "Thanks for the quick response and the help. "

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2001 park avenue in water my driver side floor is soak n water where is it coming from


Your heater water supply hose as it goes to your heater core under pass side of dash

Hope this helps Mike

Dec 08, 2015 | 2001 Buick Park Avenue

1 Answer

1999 Park avenue what can make blower stop working?


No it is likely the blower motor is defective, you can test it by removing the connector and then the blower motor and testing it by applying power to the motors connector pins.

Oct 01, 2012 | 1999 Buick Park Avenue

1 Answer

96 Buick Park Avenue, heater wont blow hot air. How can I tell if it might be the thermostat or the heater core?


Start the car and let it warm up. After it is warmed up open the hood. Look for your top radiator hose, and see if you can squeeze the hose, if the hose is hard to squeeze, the thermastat is stuck shut. If your heater core was out, it would be leaking badly.

Feb 26, 2011 | 1996 Buick Park Avenue

2 Answers

How to install a new top and bottom hvac heater hose fitting for a 2002 buick lesabre custom


The hoses are moved by turning them a few degree's, then pulling them off. See diagram below.

658aa5f.gif

Jun 19, 2010 | 2002 Buick LeSabre

1 Answer

Need to find heater blower resistor on 1991 Buick Park Avenue


GM: Electra/Park Avenue/Ninety-Eight 1990-1993 REpair Guide
Blower Resistor Module


b4bdc8d.jpg

Fig. 1 Blower resistor assembly is underneath the fuse block
REMOVAL & INSTALLATION

  1. Disconnect the negative battery cable.
  2. Remove the rear sight shield.
  3. Remove the fuse/relay block assembly and bracket.
  4. Disconnect the resistor module connector.
  5. Remove the retaining screws and remove the resistor module.

To install:
  1. Inspect the gasket and replace or repair as required.
  2. Install the resistor module and secure with screws.
  3. Connect the resistor module connector.
  4. Install the bracket and fuse/relay block assembly. Install the sight shield.
  5. Connect the negative battery cable, and check the climate control system for proper operation.
Hope this help (remember rated and comment this).

Mar 29, 2010 | 1991 Buick Park Avenue

1 Answer

Heater does not heat. The inlet and out let of the heater hoses are very warm. The radiator is full.1994 Buick Park Avenue


You have a problem with the ducting. Probably a vacuum leak, could be just a sticky flap also.

Feb 17, 2010 | 1994 Buick Park Avenue

2 Answers

92 buick park avenue won't blow hot air - temp control seems to be working


Make sure there are no leaks and that the system is full to capacity. After the vehicle has warmed up check radiator hoses for temperature differecial also check heater core hoses. A significant difference in temperature may indicate a plugged heater core or thermostat failure

Oct 22, 2009 | 1992 Buick Park Avenue

1 Answer

Heater/defrost/ac fan not coming on park avenue...can hear click


Check the connector to the blower motor. Turn it on and wiggle the connector.

Jan 10, 2009 | 1989 Buick LeSabre

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...