Question about Chrysler Cars & Trucks

Open Question

Where is the airbag occupant classification module locate 2007 chrysler town and country

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

garyq1970
  • 73 Answers

SOURCE: changing fuel filter on 2004 chrysler town and country

  1. Remove or disconnect the following:
    • Negative battery cable
  2. Raise the vehicle and support the fuel tank with a transmission jack.
    • Fuel line from the front of the tank
    • Ground strap
    • Inboard side of the fuel tank straps and front T strap fastener and lower the tank about 6 inches
    • Fuel lines from the fuel pump module
    • Fuel filter
  3. Installation is the reverse of removal. Tighten the fuel filter bolts to 40 inch lbs. (4.5 Nm), the main tank straps to 40 ft. lbs. (54 Nm) and the T strap to 250 inch lbs. (28 Nm).
  4. Start the engine and check for leaks.

Posted on Aug 24, 2008

  • 1861 Answers

SOURCE: DTC B1650 occupant classification system

If the vehicle has been in a rear end collision, expect this. If not, it just may need to have the Occ Class Sys reset. Toyota Dealer only.

Posted on Sep 08, 2008

lebones337
  • 152 Answers

SOURCE: Where is the Body Control Module located?

It is located on the back side of the underdash fuse box (junction block). You remove the lower steering column cover and knee blocker reinforcement. Then remove two plugs from the bottom of the bcm.
Remove the bolts holding the junction block to dash panel mounting bracket. Remove the junction block from the bracket. Remove screws holding the bcm to the jb. Slide the bcm downward to disengage guide studs on jb from channels on bcm mounting bracket
Remove bcm from jb.

Posted on Jan 02, 2009

emissionwiz
  • 75051 Answers

SOURCE: where is the body control module located on a 1997 town & country

It is located on the back side of the underdash fuse box (junction block). You remove the lower steering column cover and knee blocker reinforcement. Then remove two plugs from the bottom of the BCM.
Remove the bolts holding the junction block to dash panel mounting bracket. Remove the junction block from the bracket. Remove screws holding the BCM to the junction block. Slide the BCM downward to disengage guide studs on jb from channels on BCM mounting bracket

Posted on Mar 23, 2009

polarcycle
  • 1392 Answers

SOURCE: DTC B1650 occupant classification system

If it is like a Chrysler, you will need to go to the dealer and have them redo the OCS. This has to do with the passenger airbag system and how much force it will send the air bag with.

Posted on May 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you fix error code U0151 in a 2014 Lancer?


i'd start by rechecking the "MDS on" install to make sure all connectors near where you were working are well seated. also recheck where the previous harness would contact. i find it really hard to beleive that the old harness was too short. improperly routed perhaps, but too short???

U0154 - LOST COMMUNICATION WITH OCM (occupant classification module)
  • When Monitored:
  • With the ignition on
  • IOD fuse installed
  • FCM is configured correctly
  • Set Condition: Bus messages not received from the Occupant Classification Module for approximately 2 to 5 seconds.
Possible Causes
CAN B BUS CIRCUITS OPEN OR SHORTED
DTCS RELATED TO BATTERY VOLTAGE, IGNITION, OR VIN MESSAGES
FCM NOT CONFIGURED CORRECTLY
OCCUPANT CLASSIFICATION MODULE
OCCUPANT CLASSIFICATION MODULE POWER AND GROUND
MODULE THAT SET THIS DTC


OCM is located under passenger seat. make sure it's connector isn't loose.

Dec 10, 2016 | Cars & Trucks

1 Answer

Airbag codes B1206 B1204 B223D are on 2006 dodge magnum srt8


B1204 communication w/occupant classification module passenger airbag indicator circuit low

B1206 passenger airbag indicator circuit open

B223D occupant classification module DTC present

You either have a bad passenger airbag or the sensor that tells computer it is present

Sep 17, 2015 | Dodge Cars & Trucks

1 Answer

Suzuki forenza 2005 what is b1446 mean


short answer, Occupant controls failure. Passenger seat.

medium answer , air bags ,seat sensors and or seat belt systems failure.

Long answer.

no engine of the 5, are stated. nor country,



This is covered 100% in the book called FSM.

the factory service manual, on all cars. they have one

read it.? or at alldata.com and here

just $4 to read it.

https://suzukipitstopplus.com/



my best guess, is air bags (and ARE a danger to all mechanics that fail to read the FSM warnings, !!!)

the module is not communicating , due to power loss is the clue.

in case you dont know, error codes never tell you what part is bad

it at the least tells you what signal is dead, bad or a sensor not responding

what a tech,does, is do more test to ISOLATE the true cause.

others guess, and go broke fast $$$$$$



the Forenza is this Suzuki with Daewoo body and GM enigne,

are real pistol to work on,,,

rule 2, is the code is unique to suzuki, no other cars.

B1446 (i roll dice and guess)

2.0L engine, automatic.

out of FSM it states

but what does , OC mean,

its short, (not nice huh)

for

e Occupant Classification System (OCS)











Trouble Code: B1446 (2.0L L4 VIN - Auto)

OC Passenger Short to Power (Battery) or No Response








Trouble Code Conditions:

The OC sensor wiring is shorted to the battery wiring

Possible Causes:



  • Circuit


  • Sensor




OC rules before PLAYING around. a short excerpt.




If the vehicle is equipped with the Occupant Classification System (OCS), do not connect the battery negative cable before performing the OCS Verification Test using the scan tool and the appropriate diagnostic information. Personal injury or death may result if the system test is not performed properly.

Never replace both the Occupant Restraint Controller (ORC) and the Occupant Classification Module (OCM) at the same time. If both require replacement, replace one, then perform the Airbag System test before replacing the other.

Both the ORC and the OCM store Occupant Classification System (OCS) calibration data, which they transfer to one another when one of them is replaced. If both are replaced at the same time, an irreversible fault will be set in both modules and the OCS may malfunction and cause personal injury or death.

If equipped with OCS, the Seat Weight Sensor is a sensitive, calibrated unit and must be handled carefully. Do not drop or handle roughly. If dropped or damaged, replace with another sensor. Failure to do so may result in occupant injury or death.

If equipped with OCS, the front passenger seat must be handled carefully as well. When removing the seat, be careful when setting on floor not to drop. If dropped, the sensor may be inoperative, could result in occupant injury, or possibly death.

If equipped with OCS, when the passenger front seat is on the floor, no one should sit in the front passenger seat. This uneven force may damage the sensing ability of the seat weight sensors. If sat on and damaged, the sensor may be inoperative, could result in occupant injury, or possibly death.

Oct 20, 2014 | 2005 Suzuki Forenza

1 Answer

How do I turn off airbag dash lite on 2005 Chrysler Town and Country


with the air bag dash(SRS) light on there is a code in the air bag module that has to be checked out in order for the light to go out. it could be something simple, or something like the clock spring in the steering wheel has a problem.

Oct 04, 2014 | 2005 Chrysler Town & Country

1 Answer

Where is the fuse for the front passenger side airbag on a 2007 Chrysler Town and Country?


The air bags are powered thru the airbag control module.
The module gets power from two fuses in the box near the battery.

Feb 28, 2013 | Cars & Trucks

1 Answer

Where is the OCM


The Occupant Classification Module (OCM) is located under the pass seat.

Good luck.

Apr 17, 2010 | 2002 Chrysler Sebring

1 Answer

DTC B1650 occupant classification system fault. 2007 DTC B1650 occupant classification system and the vehicle has been in a rear end collision and i tried to have the OCS reset but in vain, please help


If it is like a Chrysler, you will need to go to the dealer and have them redo the OCS. This has to do with the passenger airbag system and how much force it will send the air bag with.

May 28, 2009 | 2009 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

277 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...