Question about Cars & Trucks

Open Question

Replace timing belt on 2005 hyundai xg350 v6

Working on hyundai xg350 v6 replacing timing belt,i want to know how to line up the timing marks before i take off the old belt thereare 4 marks on the 4 cams &a marks on the heads also the crankpulley.do i keep turnning the engine by hand to line up marks or do i remove the old belt & set eachcam &crank by hand &then put on the new belt. thanks tom

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

stevenhurc
  • 450 Answers

SOURCE: Looking for cambelt timing marks/ positions please, Twin cam engine Thanks Kevin

these bend valves if belt breaks while running
Align the timing marks on the camshaft gears to the notches on the camshaft cover, using the intake gear mark for the intake gear and the exhaust gear mark for the exhaust gear.
Align the mark on the crankshaft gear with the
notch at the bottom of the rear timing belt cover.

Posted on Jun 29, 2009

limotec
  • 33 Answers

SOURCE: need a diagram for 94 3l diesel hilux timing belt replacment pls.

Hello Paul
I hope this help you
6a737ed.jpg Regards Paul
www.limotec.co.uk
If you need more please contact me

Posted on Jan 13, 2009

jagjeffery
  • 318 Answers

SOURCE: TIMING BELT MARKS DONT MATCH AFTER ENGINE TURNED OVER

dont worry about that you will have to turn the motor over 40 to 50 time before those timing belt marks line up again if your pulley marks line up correctly thats all you have to worry about

Posted on May 29, 2009

SOURCE: Timing marks on cam sproket and crankshaft pully 1996 Elantra 1.8

dear friend-if your mark at the bottom is on TDC then that is fine,there is a 8mm hole in the top sprocket.alighn the hole with the mark on the cylinderhead,put belt on and tention turn ones around and lighn up marks.re-assemble.

Posted on Jul 22, 2009

  • 1757 Answers

SOURCE: trouble replacing timing belt ... setting timing

Sorry for the severe delay.
I am personally going back to answer your unanswered question.
I do not know if you still need the answer, but I am going to answer it in case you still do.

Click on the following direct Link. It has the Timing Belt Diagrams with Marks for the Camshaft and Crankshaft that you will need. It also has numerous other helpful diagrams for use.

Again my apologies...
Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!


http://www.2carpros.com/car_repair_information/year/1996/make/hyundai/model/sonata/1996_hyundai_sonata_timing_belt_diagram_marks.htm

Posted on Mar 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

Tip

What you need to know about Hyundai


I am a mechanic ..most people ask questions about these foreign hyundai motors ..below is an example of engines that basically if you ask about a Hyundai Xg 350 ,xg300 ..well allow me to hammer 90% of your questions in case you want to grab another motor ..these motors listed will work on 90% of all hyundai products ...Look at the starter sizes ,,all the same for the selected models ..then look at the motor sizes ..This will help you in solving some problems most do not give the specific questioning
100% NEW REPLACEMENT STARTER
FOR
STARTER

12 VOLT / CW ROTATION / 8 TOOTH DRIVE

REPLACES:
MANDO M62957
VALEO TM000A14401
BOSCH REMAN SR4118X
BOSCH NEWMAN SR4118N
HYUNDAI 36100-37210

FITS ON:

HYUNDAI
2001 SANTA FE 2.7L ENGINE
2002 SANTA FE 2.7L ENGINE
2003 SANTA FE 2.7L ENGINE
2004 SANTA FE 2.7L ENGINE
2005 SANTA FE 2.7L ENGINE
2006 SANTA FE 2.7L ENGINE

2003 SANTA FE 3.5L ENGINE
2004 SANTA FE 3.5L ENGINE
2005 SANTA FE 3.5L ENGINE
2006 SANTA FE 3.5L ENGINE

2002 SONATA 2.7L ENGINE
2003 SONATA 2.7L ENGINE
2004 SONATA 2.7L ENGINE
2005 SONATA 2.7L ENGINE

1999 SONATA 2.5L ENGINE
2000 SONATA 2.5L ENGINE
2001 SONATA 2.5L ENGINE

2003-2008 TIBURON 2.7L ENGINE

2005-2008 TUCSON 2.7L ENGINE

2001 XG300 3.0L ENGINE

2002 XG350 3.5L ENGINE
2003 XG350 3.5L ENGINE
2004 XG350 3.5L ENGINE
2005 XG350 3.5L ENGINE

KIA
2004 AMANTI 3.5L ENGINE
2005 AMANTI 3.5L ENGINE
2006 AMANTI 3.5L ENGINE

2001 MAGENTIS 2.5L ENGINE

2002-2006 MAGENTIS 2.7L ENGINE

2001 OPTIMA 2.5L ENGINE

2002 OPTIMA 2.7L ENGINE
2003 OPTIMA 2.7L ENGINE
2004 OPTIMA 2.7L ENGINE
2005 OPTIMA 2.7L ENGINE
2006 OPTIMA 2.7L ENGINE

2002-2005 SEDONA 3.5L ENGINE

2005 SPORTAGE 2.7L ENGINE
2006 SPORTAGE 2.7L ENGINE
2007 SPORTAGE 2.7L ENGINE
2008 SPORTAGE 2.7L ENGINE

on Oct 24, 2013 | Hyundai Cars & Trucks

1 Answer

How do you set the timing marks before i replace the timing belt 3.5 engine


Do not remove the old belt until all the marks are lined up. Only then should the old belt be removed. Turning the cams or crank with the belt removed can cause engine damage!

Nov 06, 2012 | Hyundai Motor 2005 XG350

2 Answers

I need 2004 Hyundai XG350L Service/repair Manual


3.5L Engine

Remove or disconnect the following:
  1. Negative battery cable
  • Engine coolant
  • Water pump pulley bolts
  • Alternator bolt, loosen only
  • Water pump pulley and drive belts
  • Crankshaft pulley
  • Timing belt cover(s)
  1. Turn the crankshaft until the timing marks on the camshaft sprocket and cylinder head are aligned.
  2. Loosen the timing belt tensioner bolt and turn the tensioner counterclockwise as far as it will go. Tighten the adjusting bolt.
  3. Mark the timing belt with an arrow showing direction of rotation.
  4. Remove the timing belt.
  5. If defective, remove the timing belt tensioner.

9767b45.gif
Timing belt sprocket alignment mark positioning for belt removal and installation—3.5L engine

To install:
  1. If necessary, install the timing belt tensioner.
  2. Attach the top of the tensioner spring on the engine coolant pump pin. Ensure the hook on the pin is facing down and the hook on the tensioner is facing away from the engine
  3. Rotate the timing belt tensioner to the extreme counterclockwise position. Temporarily lock the tensioner in place.
  4. Align the timing marks of the camshaft and crankshaft sprockets.
  5. Install the timing belt on the crankshaft sprocket, then onto the rear camshaft sprocket.
  6. Route the belt to the coolant pump pulley, the front camshaft sprocket and the timing belt tensioner.
  7. Apply force counterclockwise to the rear camshaft sprocket with tension on the tight side of the belt and check that timing marks are aligned.
  8. Loosen the tensioner bolt 1–2 turns and tighten the timing belt to a tension of 57–84 lbs. (260–380 N).
  9. Turn the crankshaft two turns clockwise.
  10. Readjust the sprocket timing marks and tighten the tensioner bolts.
  11. Install the timing belt covers.
  12. Install the crankshaft pulley and tighten to 108–116 ft. lbs. (150–160 Nm).
  13. Install or connect the following:
    • Timing belt cover(s)
    • Crankshaft pulley
    • A/C compressor belt
    • Water pump pulley
    • V belt
    • Negative battery cable
    • Engine with coolant

Feb 10, 2010 | 2004 Hyundai XG350

1 Answer

Is the motor in an xg350l an interference engine?


Yes, the 3500 V6 in the XG350 is an interference engine by design. Severe engine damage can occur if valve timing becomes incorrect due to timing belt failure.

Feb 09, 2010 | 2004 Hyundai XG350

1 Answer

Crank sensor and timing belt related?


Its possible, was the crank sensor physically damaged or just an internal failure. That would determine if it was a coincidence or not.

Oct 24, 2009 | Hyundai Motor 2003 XG350

1 Answer

Need to change pully


Which One?
60a96c9.jpg The one on the left has two 14mm fasteners 1 nut & 1 bolt. The one on the right has the same 1 14mm nut and 1 14mm bolt. Both are simple to replace. Step 1: Relieve the tension on the pully you wish to replace. Step 2: remove the pully (front) by removing the 14mm nut. To remove the rear tensioner pully, remove both nut & bolt.

May 19, 2009 | Hyundai Motor 2005 XG350

1 Answer

2002 XG350 - Do I need new timing and drive belts?


timing belt and most drive belts are good for 70,000miles, i think the mechanic trying to take you for a ride, as for the drive belts inspect them if there is any cracking ware marks etc replace them but seriously if they look like new which they should with only that many miles would not need replacing.

May 14, 2009 | 2004 Hyundai XG350

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

158 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...