Question about Cars & Trucks

Open Question

2005 cadillac 3.6 show how to replace harmonic balancer

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1056 Answers

SOURCE: harmonic balancer

Remove the hood, drain and remove the radiator, remove the belts, loosen the bolt into the balancer, replace part way, hook up a harmonic balance puller, tighten until balancer come free, remove puller, remove HB bolt, remove balancer.
Check seals before replacing, if damaged, replace, check keyway, replace woodruff key if needed.
Install is the reverse.

Posted on Oct 18, 2008

  • 2039 Answers

SOURCE: Harmonic balancer on a grand am

you have to remove the center bolt of harmony its depend what engine you have most likely you need a little puller if the belt loose check the belt tensionner to see if its not broken pierre

Posted on Feb 14, 2009

  • 1 Answer

SOURCE: 1993 Geo Prizm Lsi Harmonic Balancer

Yes a harmanic balancer from tha corolla is the same thing. I had to do the same thing with my 95 geo. It works out to be a lot cheaper buying for a toyota than a geo.

Posted on Mar 23, 2009

  • 2 Answers

SOURCE: HARMONIC BALANCER

I have a '94 Tempo, it had a "ticking" sound. It was the "harmonic balancer" (crankshaft pulley) a local mechanic changed it for $60, the part cost me $120 (I work for a Ford dealership) $180 without employee discount. you can get one for much less at a junkyard if you can find one. Good luck, Sean

Posted on May 14, 2009

  • 64 Answers

SOURCE: Mitsubishi Eclipse Harmonic Balancer 3.0L Removal

There is a panel inside the wheel well that you can take off that gives you perfect access to the harmonic balancer. A special tool is required. i had my dad make one because he has access to whatever he needs at the factory. but you can get them at the dealer. i have no clue how much they cost. I can't see any way of doing it without the special tool. after you get the tool its pretty simple to get off. it takes alot of force to break the bolt loose though. i used the handle off my jack as a cheater bar. hope this helps...

Posted on Jun 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove the harmonic balancer on a 2005 x5 4.4l


If you are removing the harmonic balancer for repairs, you will need to remove the engine and use a harmonic balancer bolt puller.
Do not try to remove this and run the engine. This will cause crankshaft failure due to the engine vibrations caused by the firing cylinders.

Jul 29, 2016 | 2005 BMW X5

2 Answers

Serpentine belt keeps coming off. does harmonic balancer keep it on. how do you change it


Make sure you have the right size belt. If it's old then replace it. Then make sure you run it correctly or it can slip off. If it still slips off then check all your pulleys for chips or wobble before you replace any pulleys. I hope this will be some simple help for you.

Apr 28, 2016 | 2005 Chevrolet Monte Carlo

1 Answer

How do I put a Harmonic Balancer back on my 3.5 Dodge Magnum engine?


might to go to local parts store and borrow a harmonic balancer installation tool

Jul 14, 2015 | 2005 Dodge Magnum SXT

1 Answer

Do you have to replace crankshaft sensor when replacing harmonic balancer


No. Only if the sensor is damaged by a bad harmonic balancer, or if there is a code for the sensor, or if you have no spark at the spark plug. Then one could suspect the sensor, as it helps the computer figure spark timing.

Nov 25, 2013 | 2005 Infiniti G35

1 Answer

Hamonic balance


Do you mean harmonic balancer? If so, a Harmonic balancer absorbs engine vibration and basically keeps your crankshaft from failing over a period of time. A harmonic balancer is a very important part of your engine and should be maintained accordingly.

Mar 20, 2013 | 2005 Chevrolet Impala

1 Answer

Unable to pull the harmonic balancer


need a harmonic balancer pulley you can rent them at your local auto part store

Feb 20, 2013 | 1999 Cadillac DeVille

1 Answer

The Serpentine belt keeps walking off the Crank shaft pulley by one rib as if the pulley moved away from the engine.. Is this where the harmonic balancer is. If so, is it difficult to change?


Before you change anything,,check and see if everything is in line..Also feel all the pulleys and make sure everything turns ok...If the powersteering pump has been replaced,,sometimes the pulley was not pressed on far enough..If it seem to be the harmonic balancer make sure its not damage and the bolt in the middle is tight...If you remove it..You remove middle bolt,,then you have to use a puller to remove the harmonic balancer itself..unusuall for the harmonic balancer to be bad unless it was hit by something

Sep 20, 2011 | 2005 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...