Question about 1999 Daewoo Leganza

1 Answer

Noise in top end

I had just rebuilt the motor and drove it for 2 months and one day it just got noisy in the top end

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 404 Answers

Pull rocker cover off ,run and listen

Posted on Jan 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

WHAT IS THE LIKELY CAUSED OF A LOUD SQUEALING NOISE COMING FROM THE ALTERNATOR SERPENTINE DRIVE BELT SYSTEM ? IS IT THE ALTERNATOR OR SERPENTINE BELT?


serpentine belt is getting old and hard and the cold weather was causing it to slip
check belt condition ( small cracks across the grooves = scrap and get a new one) and check tension

Jan 22, 2016 | Cars & Trucks

2 Answers

Noisy valves when hot, starts good runs great till hot then gets noisy new top end piston, new dyna jet and rebuilt head


may want to go bac and reajust valves--or try a synthetic oil like amsoil 0w30--they lower temp as much as 50degree and hav esters so motor seals dont wear

Sep 03, 2014 | Cars & Trucks

1 Answer

1999 mustang base v6 noisy rear above 50 mph


check the "u" joints and check that the drive shaft flanges have been properly fitted to the pinion flange or that the "u"joints have been properly fitted into the pinion "ears " of the pinion.. Check that the correct grade of oil was used in the diff and it has the correct amount. New out of the factory diff should not be noisy but if you have a new rebuilt diff then it is possible that the gear mesh is not correct or used gears were used where the best mesh was obtained.

May 05, 2014 | 1999 Ford Mustang Cobra

1 Answer

97 buick park avenue 3800 motor making a noise in the top end but sounds like a knock but hasnt effected the performance of the car just noisy


It is probably a noisy wrist pin on one cylinder,
also known as "a death rattle"
GM had this in their 2.2 engines,

Dec 16, 2009 | 1997 Buick Park Avenue

2 Answers

How long does a big end bearing in a 2003 ford


Do you mean a main bearing/ If so it sounds as if it was bad before you bought it unless you over rev'd the motor. The main bearings other than from over reving do't usually go just like that.

Sep 08, 2009 | Ford Fairmont Cars & Trucks

1 Answer

Daewoo laganza motor


what does the noise sound like? it may be cam noise form your cam lobes or you may have a lazy cam follower what did yo7ur motor rebuild consist of and are you sure noise is from top end and not an over tightened cambelt wich will give a noise similiar to noisy cams

Jan 05, 2009 | 1999 Daewoo Leganza

1 Answer

Camshaft and bearings


There is a very good chance that it is a noisy lifter. They can look and work fine but make noise. Alot of GM cars and trucks end up doing this and there is not anything mechanicaly wrong with them. I would NOT replace the motor because of this. I have never heard of a ticking sound being caused by something in the bottom end of the motor. If it was something in that area you would probably have wrecked the motor by now, or your oil pan would be full of metal shavings.

Jul 24, 2008 | 2002 Pontiac Grand Am

Not finding what you are looking for?
1999 Daewoo Leganza Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

61249 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...