Question about 2003 Hyundai Accent

2 Answers

Washers dont work

Hyundai 1.5 mvi washer system does not operate is there a independant fuse or relay i can check .the wipers work ok but no water through the pipes . its not frozen

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 404 Answers

Yes should have an inderpendant fuse trace wire or check with test light.,wiggle wires ,tapp washer motor gently.

Posted on Jan 05, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 716 Answers

If When You Pull The Lever To Run The Sprayer You Hear The Sprayer Motor Running Get Yourself A Sewing Needle And Put It In The Sprayer Nozzle On The Hood. Very Common Problem.

Posted on Jan 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My wiper motor only works on high and stops were ever the wipers are at. And the washer motor doest #39;t work


Low Speed Windshield Wipers
Low speed is activated when the multifunction switch supplies a specific ground to the speed inputs of the windshield wiper motor module. The windshield wiper motor module then supplies ground to only the windshield wiper run/park relay coil, activating it. When the windshield wiper run/park relay is activated, the deactivated high/low relay connects voltage to the windshield wiper motor low input activating the wiper motor. The windshield wiper motor module continues to operate the windshield wiper motor in the same manner as in high speed, but in low speed with the wiper motor connected to the low speed input.
Washer System
The windshield washer is activated by the internal wiper motor module when it receives a ground signal input from the multifunction switch. Dependent on the switch selection, the internal wiper motor module activates the windshield washer relay (internal) by grounding the respective relay coil. When the relay is activated, it connects voltage to the washer pump while the washer level switch provides ground to the washer pump.
Visual Inspection Chart Mechanical Electrical
  • Windshield washer hoses
  • Wiper linkage
  • Multifunction switch
  • Battery junction box (BJB) fuse 110 (30A)
  • Central junction box (CJB) fuse 13 (10A)
  • Circuitry
  • Windshield wiper motor
Symptom Chart Condition Possible Sources Action
  • The wipers are inoperative
  • Fuse(s)
  • Circuitry
  • Multifunction switch
  • Windshield wiper motor
  • Go To Pinpoint Test A .
  • The wipers stay on continuously
  • Circuitry
  • Multifunction switch
  • Windshield wiper motor
  • Go To Pinpoint Test B .
  • The high/low wiper speeds do not operate correctly (intermittent wiper mode OK)
  • Circuitry
  • Multifunction switch
  • Windshield wiper motor
  • Go To Pinpoint Test C .
  • The intermittent windshield wiper speed does not operate correctly (high/low speeds OK)
  • Circuitry
  • Multifunction switch
  • Windshield wiper motor
  • Go To Pinpoint Test D .
  • The wipers will not park at correct position
  • Pivot arm adjustment
  • Linkage
  • Windshield wiper motor
  • REFER to Windshield Wiper Blade and Pivot Arm Adjustment in this section.
  • The washer pump is inoperative
  • Circuitry
  • Windshield washer pump
  • Multifunction switch
  • Windshield wiper motor
  • Go To Pinpoint Test E .
Do you know how to do electrical testing ?
  • windshield wiper motor
  • PINPOINT TEST C: THE HIGH/LOW WIPER SPEEDS DO NOT OPERATE CORRECTLY (INTERMITTENT WIPER MODE OK) s6a~tr~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use the correct probe adaptor(s) when making measurements. Failure to use the correct probe adaptor(s) may damage the connector.
    Test Step Result / Action to Take C1 CHECK THE MULTIFUNCTION SWITCH
    • Key in OFF position.
    • Disconnect: Multifunction Switch C202b.
    • Carry out the multifunction switch component test. Refer to Wiring Diagrams Cell 149 for schematic and connector information.
    • Does the multifunction switch pass the component test?
    Yes
    GO to C2 .

    No
    INSTALL a new multifunction switch. REFER to Section 211-05 . C2 CHECK CIRCUIT 57 (BK) FOR AN OPEN
    • Measure the resistance between the multifunction switch C202b-5, circuit 57 (BK), harness side and ground.
      s6a~tr~en~file=n0025872.gif~gen~ref.gif
    • Is the resistance less than 5 ohms?
    Yes
    GO to C3 .

    No
    REPAIR the circuit. TEST the system for normal operation. C3 CHECK CIRCUITS 56 (DB/OG), 61 (YE/RD), AND 63 (RD) FOR OPENS
    • Disconnect: Windshield Wiper Motor C125.
    • Using the following table, measure the resistance between the multifunction switch C202b harness side and the windshield wiper motor C125 harness side:

      Multifunction Switch C202b Windshield Wiper Motor C125 pin 6, circuit 56 (DB/OG) pin 10, circuit 56 (DB/OG) pin 1, circuit 61 (YE/RD) pin 1, circuit 61 (YE/RD) pin 4, circuit 63 (RD) pin 9, circuit 63 (RD)

      s6a~tr~en~file=n0025874.gif~gen~ref.gif
    • Are the resistances less than 5 ohms?
    Yes
    GO to C4 .

    No
    REPAIR the circuit. TEST the system for normal operation. C4 CHECK FOR CORRECT WIPER MOTOR OPERATION
    • Disconnect all wiper motor connectors.
    • Check for:
      • corrosion
      • pushed-out pins
    • Connect all wiper motor connectors and make sure they seat correctly.
    • Operate the system and verify the concern is still present.
    • Is the concern still present?
    Yes
    GO to C5 .

    No
    The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector. TEST the system for normal operation. C5 CHECK THE WINDSHIELD WIPER MOTOR
    • Key in OFF position.
    • Disconnect: Windshield Wiper Motor C125.
    • Carry out the windshield wiper motor component test as outlined in this section.
    • Does the windshield wiper motor pass the component test?
    Yes
    The system is operating correctly at this time. The concern may have been caused by binding or incorrect pivot arm adjustment. REFER to Windshield Wiper Blade and Pivot Arm Adjustment in this section. TEST the system for normal operation.

    No
    INSTALL a new windshield wiper motor. REFER to Windshield Wiper Motor in this section.

    Jul 20, 2016 | 2006 Mercury Grand Marquis

    1 Answer

    Head light washers do not work:fuse and water level okay.Have turned Lights on.Have tried at irregular intervals and pulled wiper stalk in every direction.Windscreen washers work well:


    Did you check to see if you have power to the wiper motors on the headlights? If you're sure the fuse is ok and you actually checked the fuse for voltage, then check the wiper motors for voltage, if the wipers don't have voltage to them then trace the wiring back, you'll probably find a break in the wiring or a relay that went bad. If you do have voltage, then start checking for a bad ground.

    Jul 17, 2016 | 2005 Mini Cooper Convertible

    1 Answer

    Cadillac Deville 99


    Wiper/Washer System (Pulse) Schematics (w/o CE1)
    Wiper/Washer System (Pulse) Schematics (w/CE1)

    Which one does yours have ?

    The switch could be bad or the windshield wiper / washer module . Do you own a DVOM - digital volt ohm meter ? Do you know how to do automotive electrical trouble shooting ? There are a few good videos on youtube on basic electrical trouble shooting an how to read wiring diagrams . Go to http://www.bbbind.com/free_tsb.html for free wiring diagrams . Check B+ voltage at the switch (in an out ) at the different speeds .Check for B+ voltage at the wiper washer module , it's part of the wiper motor .
    The windshield wiper/washer system consists of a permanent-magnet depressed-park wiper motor assembly, a wiper transmission assembly, wiper arm and blade assemblies, a washer pump mounted on a washer solvent container, and a wiper/washer switch assembly.
    The wiper/washer system is a pulse (delay) type. Pulse timing and demand wash functions are controlled electronically. Wiper/Washer System Description (Rainsense)
    The windshield wiper/washer system consists of a Rainsense module, a permanent-magnet, depressed-park wiper motor assembly, a wiper transmission, wiper arm and blade assemblies, a washer pump mounted on a washer solvent reservoir, and a wiper/washer switch assembly.
    The wiper/washer system is a rain sensing type. Rainsense functions are controlled electronically. 1
    Was the Wiper/Washer System Check performed?
    --
    Go to Step 2
    Go to Wiper/Washer System Check

    2
    Inspect the WIPERS fuse A9 for an open.
    Is the fuse open?
    --
    YES - Go to Step 3
    NO - Go to Step 4

    3
    Replace the WIPERS fuse.
    Is the replacement complete?
    --
    Go to Wiper/Washer System Check
    --

    4
    Disconnect the wiper/washer switch connector C202.
    Turn ignition switch ON.
    Connect a test light from connector C202, terminal E5 to ground.
    Is the test light on?
    --
    YES - Go to Step 16
    NO - Go to Step 5

    5
    Connect a test light from Accessory Relay, terminal A1, to ground.
    Is the test light on?
    --
    YES - Go to Step 6
    NO - Go to Step 11

    6
    Connect a test light from Accessory Relay, terminal A3, to ground.
    Is the test light on?
    --
    YES - Go to Step 7
    NO - Go to Step 12

    7
    Connect a test light from Accessory Relay, terminal B1 to terminal A3.
    Is the test light on?
    --
    YES - Go to Step 8
    NO - Go to Step 15

    8
    Inspect CKT 143 for an open or poor connection between connector C202 and the Accessory Relay.
    Was an open or poor connection found?
    --
    YES - Go to Step 9
    NO - Go to Step 10

    9
    Repair the open or poor connection in CKT 143.
    Is the repair complete?
    --
    Go to Wiper/Washer System Check
    --

    10
    Replace the the Accessory Relay.
    Is the replacement complete?
    --
    Go to Wiper/Washer System Check
    --

    11
    Repair the open in CKT 1040 or the power feed circuit to the WIPERS fuse.
    Is the repair complete?
    --
    Go to Wiper/Washer System Check
    --

    12
    Inspect the ACC fuse C13 for an open.

    let me know if you make it this far an then I will send the rest of testing procedures !

    Mar 09, 2016 | Cadillac DeVille Cars & Trucks

    3 Answers

    Windshield wipers don't shut off and washers don't work


    So that wipers park properly, the wipers have 2 power sources. One is from the dash switch to turn the wipers no and off, but the second is the parking power, which is always supposed to be on. The parking power is supposed to be shut off by a rotating cam inside of the wiper motor housing itself. If you don't want to take it out and fix it, you could always just pull the parking wire to the wipers, and then try to manually park them by shutting off the wipers at exactly the right time.

    Jan 11, 2016 | 2002 Mercury Cougar

    1 Answer

    Wipers dont work


    This is a complex wiper system . Here are all the components involved !
    The Wiper/Washer System consists of the following components:
    ?€¢
    Windshield wiper/washer switch


    ?€¢
    Body control module (BCM)


    ?€¢
    Wiper 1 relay


    ?€¢
    Wiper 2 relay


    ?€¢
    Wiper diode


    ?€¢
    Windshield wiper motor


    ?€¢
    Windshield washer pump


    ?€¢
    Windshield washer nozzles


    ?€¢
    Windshield washer solvent container


    ?€¢
    Windshield wiper arm and blade assemblies


    ?€¢
    Windshield wiper transmission


    ?€¢
    WIPER/SW 10A fuse


    ?€¢
    WIPER 25A fuse


    Circuit/System Description
    The body control module (BCM) controls the wiper motor based on input from the windshield wiper washer switch. The BCM monitors the wiper washer switch through three separate signal circuits and a ground circuit. The windshield wiper switch high signal circuit is used to determine high speed wiper operation, the windshield wiper switch low signal is used to determine low speed, intermittent, and mist operation through the use of a resistor ladder, and windshield washer switch signal circuit is used to determine washer operation. The windshield wiper motor park operation is controlled by the BCM. The BCM recieves an input from the park switch to determine wiper blade position. When the wiper blades are at the bottom of the windshield glass in park position the wiper park switch will open and the circuit will be pulled up to B+ by the BCM. The park signal will be pulled to ground by the wiper motor park switch while the wiper blades are not in the park position.
    The BCM controls the windshield wiper motor through two output controls, controlling two relays which determine the desired wiper speed, high or low
    Diagnostic Trouble Codes (DTCs)
    The body control module (BCM) monitors the voltage on the windshield wiper switch signal 2 circuit for diagnostic purposes. If the circuit is shorted to voltage while the driver is commanded OFF, the BCM will store DTC B3715. If the circuit is shorted to ground while the driver is commanded ON, the BCM will store DTC B3715. Refer to DTC B3715.
    It would be best to have a factory scan tool to diagnose this problem . it would make it easier anyway .
    It

    Dec 05, 2015 | Cars & Trucks

    2 Answers

    I have a 2007 mustang an the wipers wont turn off I had 2 pull the fuse to turn them off can u help me


    The windshield wiper motor is a smart wiper motor with an integrated electronics module. The internal components of the motor are the high/low relay, washer pump relay, and the run/park relay and associated electronics.
    The windshield wiper motor receives its inputs from the windshield wiper/washer switch. These signals are ground reference signals. When the switch is placed in different positions, various input signals are selected and sent through circuits to the motor. The windshield wiper motor module identifies these selected input signals and activates the motor to the selected function.!
    Your probably going to need a new wiper motor ! ! ! But you should always test before replacing parts !
    Visual Inspection Chart Mechanical Electrical
    • Windshield washer pump hoses
    • Windshield wiper mounting arm and pivot shaft
    • Bussed electrical center (BEC) fuse 10 (30A)
    • Smart junction box (SJB) fuse 3 (10A)
    • Circuitry
    • Windshield wiper motor
    • Windshield washer pump
    • Windshield wiper/washer switch
    • The wipers stay on continuously
    • Circuitry
    • Windshield wiper motor
    • Windshield wiper/washer switch
    • Go To Pinpoint Test C .
    PINPOINT TEST C: THE WIPERS STAY ON CONTINUOUSLY s6b~tr~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use the correct probe adaptor(s) when making measurements. Failure to use the correct probe adaptor(s) may damage the connector.
    Test Step Result / Action to Take C1 CHECK THE WINDSHIELD WIPER/WASHER SWITCH
    • Key in OFF position.
    • Disconnect: Windshield Wiper/Washer Switch C2137.
    • Carry out the windshield wiper/washer switch component test. Refer to Wiring Diagrams Cell 149 for schematic and connector information.
    • Does the windshield wiper/washer switch pass the component test?
    Yes
    GO to C2 .

    No
    INSTALL a new windshield wiper/washer switch. REFER to Wiper/Washer Switch in this section. C2 CHECK CIRCUITS 56 (DB/OG), 58 (WH), 61 (YE/RD), AND 63 (RD) FOR A SHORT TO GROUND
    • Disconnect: Windshield Wiper Motor C125.
    • Measure the resistance between the windshield wiper motor C125, harness side and ground as follows:

      Windshield Wiper Motor C125 Pin Circuit C125-10 56 (DB/OG) C125-11 58 (WH) C125-1 63 (RD) C125-9 61 (YE/RD)

      s6b~tr~en~file=n0011980.gif~gen~ref.gif
    • Are the resistances greater than 10,000 ohms?
    Yes
    GO to C3 .

    No
    REPAIR the circuit(s). TEST the system for normal operation. C3 CHECK FOR CORRECT WINDSHIELD WIPER MOTOR OPERATION
    • Disconnect all the windshield wiper motor connectors.
    • Check for:
      • corrosion.
      • pushed-out pins.
    • Connect all the windshield wiper motor connectors and make sure they seat correctly.
    • Operate the system and verify the concern is still present.
    • Is the concern still present?
    Yes
    INSTALL a new windshield wiper motor. REFER to Wiper Motor in this section. TEST the system for normal operation.

    No
    The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector.
    You

    Feb 20, 2015 | 2007 Ford Mustang Coupe

    1 Answer

    Front washer wont work mon a 2004 toyota avensis. wipers ok but washer not working. Checked fuses and seem ok. There is no fuse marked for washer. Only found 25 amp for wipers.


    1- when you pull the washer lever, do you hear or feel sound of mini washer water pump working?:
    - if Yes, you have a blockage in pipes.... this occurs usually because of impurities, rust, precipitations of soap and cleaners might be used!! check them starting from water resevoir ending with spraeyer under hood
    - if NO, you have a problem with either:
    - FUSE
    - Water mini pump (this is rare!)

    Dec 30, 2010 | Toyota Avalon Cars & Trucks

    1 Answer

    1997 explorer washer problem


    check the wiper run relay number 1 in the power distro box. Ford Explorers are bad about these relays either not making contact or being bad, swap with know good relay from another system on your truck to verify

    May 22, 2009 | 1999 Ford Explorer

    2 Answers

    The rear wiper on my '99 model exped isnt working ,ford global says its the motor and it will cost me P13k . any one who can help me find a mechanic do some repair on this?


    what is P13K?

    check the fuse first. dealer can hook up NGS Tester and get fault codes to see what is wrong.

    Principles of Operation
    NOTE: The generic electronic module (GEM) will not activate the rear wiper system if either the liftgate or the liftgate glass is ajar. If either the liftgate or the liftgate glass becomes ajar while the rear wiper is in operation, the GEM will park the rear wiper motor.
    There are two distinct modes of wiper operation:
    • Off Mode: In this mode, there is no rear wiper activity, and the wiper motor will be in the PARK position.
    • Interval Mode: This mode is selected when the rear wiper switch is in either the Interval 1 or 2 position. When this mode is selected, the rear wiper motor is driven up onto the glass by activating the rear wiper UP relay. When the wiper motor HIGH/LOW/PARK position input reaches the high position, the UP relay is deactivated and the DOWN relay is activated to reverse the wiper motor direction. When the wiper motor reaches the LOW position, as determined by the HIGH/LOW/PARK position input, the GEM deactivates the DOWN relay and will begin a new wiper cycle 1 to 10 seconds later, depending on the interval position selected.
    To engage the rear window washer, rotate the rear window washer selector downward to the WASH position. The rear window wiper will run as long as the WASH position is selected. When the rear window washer selector returns to the OFF, INT 1 or INT 2 position, the washer will stop immediately, but the rear window wiper will continue for two to three sweeps and then return to its previous mode of operation.
    The low washer fluid indicator chime warns that the washer fluid level is low. The low washer fluid indicator chime is a single tone with a duration of one second. The chime will sound when the low washer fluid indicator is initially activated.
    The low washer fluid indicator warns that the fluid level in the washer reservoir is low. The low washer fluid indicator will illuminate when the washer fluid level is low and the ignition switch is in the RUN position.
    The low washer fluid indicator will deactivate when the washer fluid reservoir is filled and the ignition switch has been cycled from RUN to OFF, then to RUN.
    Inspection and Verification
    1. The wiper/washer system is a generic electronic module (GEM) controlled system; refer to Section 419-10 .
    1. Verify the customer concern by operating the wiper/washer system.
    1. Visually inspect for obvious signs of mechanical and electrical damage.


    Visual Inspection Chart Mechanical Electrical
    • Hoses to windshield washer pump
    • Wiper linkage
    • Fuses 6 (5A), 8 (5A), 15 (5A), and 20 (5A)
    • Wiring harness
    • Loose or corroded connector(s)
    • Relays
    • Motors
    • Multifunction switch
    • Washer fluid level switch


    ----------------------------------------
    • The wipers are inoperative — rear
    • Fuses 6 (5A), 8 (5A), 15 (5A), and 20 (5A).
    • Circuitry.
    • GEM.
    • Multifunction switch (wiper/washer switch).
    • Rear wiper up relay.
    • Rear wiper down relay.
    • Rear wiper motor.

    May 12, 2009 | 1999 Ford Expedition

    2 Answers

    Windscreen washer won't work


    the tube goes along side the apron and goes into the bottom of the washer reservoir which is behind the headlighplease rate my response thank you very much

    Jan 28, 2009 | 1994 Hyundai Excel

    Not finding what you are looking for?
    2003 Hyundai Accent Logo

    180 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Hyundai Experts

    yadayada
    yadayada

    Level 3 Expert

    60769 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6811 Answers

    Are you a Hyundai Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...