Question about Cars & Trucks

Open Question

Engine code p1521 2006 jeep commander - Cars & Trucks

Posted by on

  • Greg C Nov 08, 2012

    Finished an oil change, & filter drove around block & code went away.

×

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2008 jeep commander it is showing a transmission speed input sensor code can I drive it to get me home or should it be fixed


it has to be fixed as it determines when the gears are selected against engine rpms
it is a sensor so it should drive but be prepared for selection problems while driving
check for wires and clean connections at the transmission

Jun 20, 2015 | 2008 Jeep Commander

1 Answer

How do i remove engine oil pan on 2006 jeep commander 4.7


ALWAYS, ALWAYS, ALWAYS.......CONSULT A SHOP MANUAL!
YOU MAY HAVE TO REMOVE UNDER ENGINE SUPPORT COMPONENTS, EXHAUST, ++...OR IT MAY JUST UNBOLT AND DROP DOWN

Nov 24, 2014 | Jeep Cars & Trucks

1 Answer

We have a 2008 jeep commander, check engine light is on. ran a diagnostic because of engine noise, it said cylinder 4 misfire. so far we replaced the or, sparkplug, and coil for cylinder 4, it still h


google jeep commander forums join one and post youre question there if no luck than google grand cherokee forums and try there it is basicially the same vehicle

Feb 05, 2013 | 2008 Jeep Commander

1 Answer

My code that came up when the engine light came on was PO521


P0521 Jeep - Engine Oil Pressure Sensor/Switch Circuit Range/Performancexicon.jpghttp://engine-codes.com/p0521_dodge.htmlForum CodePossible causes- Low oil level or motor mechanical fault
- Open or short oil level sensor circuit condition
- Poor oil level sensor electrical connection
- Faulty oil pressure sensor

Jul 02, 2012 | 2006 Jeep Commander Limited

1 Answer

2006 Jeep Commander , Hemi Engine V-8 Engine error codes: P3400 P3497 P1521


P3400
P3400 Cylinder Deactivation System



P3497
P3497 Cylinder Deactivation System

P1521
This code indicates wrong oil used. This could mean either the wrong oil was put in at you last oil change, your engine was operating under high ambient temperatures

Nov 21, 2010 | Jeep Commander Cars & Trucks

1 Answer

My 06 jeep commander has the engine light on.the trouble code is for trans over temp no matter how long its been sitting


it is proably a bad harness coming out of the fuse box under the hood - read about this problem in another forum

Jan 25, 2010 | 2006 Jeep Commander

1 Answer

I have a 2006 Jeep Commander. The malfunction light came on. How can I check to see what the codes are?


I believe that the 2006 Commander uses the newer CAN protocol, which replaced the ODB-II system. Many of the auto parts stores such as Autozone have a scan tool that they can hook up and read the codes that are causing the malfunction light to come one (sometimes also referred to as the check engine light or service engine light). If you go there and tell them the year make and model they should be able to tell you if they can read the code.

Once you have that code they should be able to tell you what it means and if that is not helpful or clarify the issue, post it up here and I will see what I can find for you regarding the issue.

Dec 31, 2008 | Jeep Commander Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

148 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...