Question about 2004 Volkswagen Eurovan

Open Question

Wipers wont work on middle speed on vw lt35 van

Have had new motor and linkages fitted

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 120 Answers

SOURCE: Wipers are not working

take out the bolt out of the wiper arm and check the spline, if the spline appears to be worn out, replace the wiper arm and tighten it. take caution in tightening the bolt for you might crack the windshield. goodluck!

Posted on Dec 15, 2008

Ad
emissionwiz
  • 76846 Answers

SOURCE: Intermitent Wiper does not work

the most common cause of this is the wiper switch.

Posted on Jan 07, 2009

  • 89 Answers

SOURCE: steps for replacing wiper motor for 1998 VW Jetta

remove wipers. remove plastic covering by loosening plastic screws first. unplug wiper motor wires. there are about three 10mm nuts at the motor location and you also have to unscrew the big nuts that were below the wipers when you unscrewed them. replacement is reversal.

Posted on Mar 26, 2009

FixinFax
  • 3085 Answers

SOURCE: VW LT35 hengine heater light comes on while

Hengine? Is that a motorized chicken?

Posted on Oct 02, 2009

steve_e_uk
  • 1675 Answers

SOURCE: 2000 VW jetta VR6 windshield wipers wont work

first try the fues box see if you have a blown fues, next if you put your wipers on can you hear the motor running for them? if you can the linkage has poped off from the motor, its a bit awkward to get it back on and no gaurentee that it will saty on, you might have to replace linkage, or, it might be the cogs on the actual wiper arms have splayed and are now smooth so they dont grip to move, you can take them off by the nut on the arm , get a can (coke can or simular) cut a rectangle out of it the hight and width if the cog, rap it round the cog, (make sure it does not overlap on the ends) and force the arm back into place and then do the nut up, this is just a short quick fix if that is the case you will have to replace the motor, also you can check the relay to the motor in the fues box, give it a tap a couple of times it might work again if not replace it...hope you find these sugestions helpful

Posted on Feb 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 2002 chevy venture and the front wipers quit working and i still hear the motor running.Stuck need help to solve this problem???


If the motor is working, the linkage between the motor and the wipers has broken. I don't have a Venture, but usually there is a plastic panel below the windshield, where the wiper arms are mounted. You remove the wiper arms, then remove the plastic panel (might be screws or it might just snap out) to get at the linkage and motor. Dealer or auto parts store should be able to order new linkage arms for you.

Nov 24, 2014 | 2002 Chevrolet Venture Passanger

1 Answer

I have a 1993 Voyager van. the front wipers stopped. I replaced the motor and the linkage bushings. There seems to be no power. the wipers move freely when no connected to motor. I do not hear any...


it would be the relay. don't know this model well but it is usually behind the fuse box. it is a speed control relay with timer in it. intermittent control and speed 1-3. or 4 on some models. when pipers working should hear it clicking on intermittent setting on wiper.

Sep 11, 2013 | 2003 Chevrolet Cavalier

2 Answers

WIPER MOTOR RUNS BUT WIPERS WONT MOVE


everyone will tell you that the linkage/transmission will need to be replaced but it doesn't,,most of the time its a bushing and O'Rielly's auto parts sells a "WIPER LINKAGE BUSHING ASSORTMENT" part# 49447 and it sells for about $5 bucks. Its fits tight and took a few minutes to install but its worth the trouble to save about $100

Feb 28, 2013 | 2008 Pontiac G6 Sedan

2 Answers

Vw golf mk3 wipers not working,fuse ok. sometimes work if blades assisted manually


WIPER ARM LINKAGE COULD BE BINDING.REMOVE WIPER ARM TO SEE IF WIPER MOTOR OPERATE SLOWLY.IF YES CHECK TO MAKE SURE WIPER MOTOR GETTING GOOD GROUND CONNECTIONS BY CHECKING MOVING WIRES .IF WIPER MOTOR SPEEDS UP YOU HAVE GROUND WIRE PROBLEM. IF WIPER MOTOR REMAIN SLOW GROUND WIRES CHECK OUT OKAY.REPLACE WIPER MOTOR.IF WIPER MOTOR RUN FAST NORMAL SPEED AFTER DISCONNECTING WIPER ARM.WIPER ARM LINKAGES IS BINDING OR NEED SOME LUBRICATION TRY WD40 SEE WHAT HAPPENS.LUBRICATION DONT HELP WIPER LINKAGE COULD BE DAMAGED.

Nov 18, 2010 | 2000 Volkswagen Golf

3 Answers

My rear windshield wiper stopped working on my 2001 Chevrolet Tahoe. I can hear the motor working but when we replace the motor it still wont work.


My 2005 tahoe did the same thing. I also bought a new motor, which did not fix. I discovered there was a bad ground. Instead of searching for bad ground, just install a short length of stranded wire with crimp terminals between a wiper motor mounting bolt and a rear glass latch assy mounting bolt to restore good grounding to the wiper motor.

Apr 02, 2010 | 2001 Chevrolet Tahoe

2 Answers

2000 VW jetta VR6 windshield wipers wont work


first try the fues box see if you have a blown fues, next if you put your wipers on can you hear the motor running for them? if you can the linkage has poped off from the motor, its a bit awkward to get it back on and no gaurentee that it will saty on, you might have to replace linkage, or, it might be the cogs on the actual wiper arms have splayed and are now smooth so they dont grip to move, you can take them off by the nut on the arm , get a can (coke can or simular) cut a rectangle out of it the hight and width if the cog, rap it round the cog, (make sure it does not overlap on the ends) and force the arm back into place and then do the nut up, this is just a short quick fix if that is the case you will have to replace the motor, also you can check the relay to the motor in the fues box, give it a tap a couple of times it might work again if not replace it...hope you find these sugestions helpful

Feb 08, 2010 | 2000 Volkswagen Jetta TDI

1 Answer

My wipers are very slow on all speeds and keep sticking


Common problem with Golf, the wiper linkages are partially seized on the spinldes. The spindles are the rods that stick up out through the plastic panel at the bottom of the windscreen and the wiper arms connect to them.
Disconnect the wiper linkage from the motor and try manually moving them but I think you will find that they are seized. You will need to completely remove the linkage assembly and clamp it in a vice and use a lubricant spray oil to work into the spindles. Either that or fit a new or good second hand linkage

Aug 02, 2009 | 2004 Volkswagen Golf

1 Answer

I have a 2008 vw jetta and the other day we had a snowstorm when i started the car and turned on the wipers they made a pop sound and wont work now.


I LOVE YOUR SCREEN NAME!!!!!!!!!!!!!!!!!!!!!!!! The Motor is Bad or you have a Broken Linkage. You can Check for a Broken Linkage By having someone hold the Switch in and see if you here the Motor make any Noise. If Not, You will need a New Wiper Motor. Please Rate My Response! Thanks!

Jan 31, 2009 | 2006 Ford F 350 Super Duty

1 Answer

Wipers wont come on


THEY CALL IT YHE WIPER TRANMISSION. THE LINKAGE THAT IS CONNECTED TO THE WIPER MOTOR FELL OFF BECAUSE THE NUT THAT KEEPS IT SECURED TO THE MOTOR LOOSENED & FELL OFF ALLOWING THE LINKAGE TO FALL OFF OF THE WIPER MOTOR.FIRST YOU HAVE TO GET A NEW NUT TO HOLD ON THE LINKAGE (IT MIGHT BE RIGHT UNDER THE WIPER MOTOR IF THERE WAS SOMEPLACE FOR IT TO FALL)REINSTALL THE LINKAGE, (IT ONLY FITS ONE WAY) PUT ON THE NEW NUT (TIGHTEN IT ENOUGH BUT MAKE SURE THE WIPERS CAN STILL ROTATE) AND YOU SET

Dec 13, 2008 | 1986 Oldsmobile Cutlass Supreme

Not finding what you are looking for?
2004 Volkswagen Eurovan Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8548 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...