Question about Cars & Trucks
You must raise the truck up an access the bulbs from the rear of the bumper.
Posted on Nov 06, 2012
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
the solution is simple,
you only need to undo the screw on top of the side light/indicator. then facing the head light place a flat headed screw driver under the bottom lip of side light. the bottom of the lihgt is on a small push fit stud, use a sponge or cloth to protect your bumper paint work then just apply pressure gently to lever side light out towards you, It will come dont worry, you may then change your bulbs if you wish remove the whole light unit you will see the bottom bolt as soon as you release the side light. to replace just push back into place then replace screw. whole job takes about five minutes
hope this helps kevan hildred
Posted on Jan 28, 2010
hi have not had pleasure of this on santa fe yet? but will try to help dependant of which side o/s or n/s ? i would first remove the screws holding the front of the under engine plastic cover/shield and drop down sufficient to gain view/access? to the rear of fog lamp then if a cover is on? try turning anti clock to remove? or if rubber cover pull off? then the bulb and clip should be visible? unplug the wire from bulb then the spring clip holding bulb in place normally just sring the 2x top ends together and swing down/clear to remove bulb? refit new bulb correctly! pay attention to position old bulb positioned? then clip securely and re connect wire at this stage it would be best to ensure bulb works ?? before you re assemble all else? wish you luck and hope this helps with your problem ?
Posted on Oct 28, 2008
SOURCE: Fog light bulb replacement
This bulb can be replaced without removing the washer fluid reservoir. There are 3 screws that go through the bottom edge of the bumper cover into the right inner fender guard. Remove these screws and pull the inner fender down to gain access to the back side of the fog lamp and remove the bulb.
Nissan Scope Technician- 10+ years experience in Nissan dealership.
Posted on Nov 04, 2008
Look up into the bumper and see if you can access the fog light. The bulb should just twist out of the back. If not, the assembly should either pop forward or back to come out. I've heard though, that many santa fe's require the removal of the entire front bumper fascia just to get to the bulbs in which case you'd have to remove your headlights to get to the screws holding the bumper fascia on
Posted on Sep 09, 2009
Look under the bumper and you will see two large phillips head screws right in front of the wheels. Take these two screws out and bend/move the plastice piece out of the way. Now you can easily get to the bulb. There is a cap that twists off that protects the wires and back of the bulb. Twist this off and then remove the plug portion from the back of the bulb. The bulb then turns 1/4 to 1/2 revolution to loosen and remove. Reverse steps for installation.
Posted on Dec 19, 2009
Tips for a great answer:
Sep 17, 2014 | 2010 Hyundai Tucson
Jan 04, 2011 | 2005 Hyundai Tucson
Nov 04, 2010 | 2006 Hyundai Sonata
Sep 09, 2009 | 2002 Hyundai Santa Fe
Aug 12, 2009 | Hyundai Motor 2005 XG350
Mar 19, 2009 | 2001 Hyundai XG300
Nov 23, 2008 | 2003 Hyundai Tucson
Oct 28, 2008 | 2007 Hyundai Santa Fe Limited
Aug 08, 2008 | 2002 Hyundai Santa Fe
Apr 24, 2018 | BMW Cars & Trucks
487 people viewed this question
Usually answered in minutes!