Question about GMC Cars & Trucks

1 Answer

Set time in a 2006 gmc 1/2 ton - GMC Cars & Trucks

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • GMC Master
  • 76,164 Answers

That info is in the woner's manual. If you don't have the OM then go here and download it from the GM site after you register. It is free

Posted on Nov 06, 2012


5 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 124 Answers

SOURCE: bad front wheelbearing 2006 gmc sierra 1/2 ton pickup

Not too bad. Just break down the Hub and pull it out. You might need a big socket. Go get a chilton's manual, it will help you if you don't understand it.

Posted on Mar 26, 2009

  • 1 Answer

SOURCE: change out a Starter in 1995 GMC Truck 1/2 ton

shes easy , two bolts and two plug wires cant screw up , worst part is the room you have to work with , try get front of truck off the ground so you can manover

Posted on Oct 29, 2009

  • 97 Answers

SOURCE: How many grease fitings on my 2006 GMC Sierra 4x4


Posted on Mar 22, 2010

  • 76164 Answers

SOURCE: 2006 gmc 1/2 ton 4l60e codes po753 785 740 2761

Based on the OBD2 fault codes you have this is either a faulty ground to the transmission shift solenoid pack due to a defect in the wiring harness or you have a defective PCM/TCM (Powertrain Control Module). At this point the wiring harness needs to be hooked up to a breakout box and each one of the circuits looked at to see if the signal to shift is being sent by the PCM/TCM. There is no one answer to a problem like this. I would suggest a good Transmission shop with the proper equipment or your local GM dealer. If you plan to try and manual test each circuit then you will need to buy a factory service manual set with full detailed wiring diagrams, these manuals are copyrighted and not free to share or download. You can purchase a year to the rights to download the factory manuals from this site all factory service manuals and factory bulletins are available to download. The cost of the service is about $40.00 for a one year subscription. I have no affiliation with this site it is just a recommendation to help you find the problem.

Posted on Aug 11, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2006 GMC 1 ton heater fan not working

To look up wiring I need more info, What is the model? Is it a 2500 or 3500, what is engine size?
Check the blower motor wiring connector for voltage and ground with hvac on.
Can you check for hvac trouble codes? Some of the national brand auto stores will check some codes for free.

Dec 03, 2015 | GMC Cars & Trucks

2 Answers

How do you pull a 1979 gmc jimmy 4x4 rear right axle

QU40221 19 Spline Outer Axle Shaft for 1977 to 1991 Chevy, GMC Corporate GM 10 Bolt Front Axle is a genuine original equipment outer axle stub shaft for all GM 10 Bolt front axles in 1977 to 1991 Chevy Blazers, GMC Jimmys, and Suburbans, plus Chevy, GMC 4x4 1/2 ton and 3/4 ton Pickups. The splined end on these new axle shafts has three snap ring grooves in three places so they are compatible with all types of automatic and manual lockout hubs plus all full-time solid splined drive gears.

Also available while supplies last: QU40221U Used Outer Axle Shaft with 3 snap ring grooves and QU40660UUsed Inner Axle Shafts with 2 snap ring grooves (QU40660U is not compatible with automatic locking hubs)

see this vdio

Apr 01, 2015 | GMC Jimmy Cars & Trucks

1 Answer

How to set the timing on a 1997 gmc 1500 5.7


1997 GMC Truck C1500 1/2 ton P/U 2WD 5.7L SFI 8cyl

The Ignition Timing


Oct 15, 2014 | GMC C1500 Cars & Trucks

1 Answer

How do I replace rear bearings on a 2006 GMC Sierra 1 ton dually?

very carefully get a repair manual this will help you step by step

Sep 29, 2014 | Cars & Trucks

1 Answer

Where is the abs relay on a 2006 gmc savana half ton van?

The ABS is controlled by the ABS Module from fuse 48 in the under the hood fuse block. It is a 60 amp in the rear most left corner looking at it from the front drivers side

Jul 12, 2014 | 2006 GMC Savana

1 Answer

Is my 1995 GMC Sonoma 4x4 a half ton truck

small trucks like that are considered 1/4 ton. silverado 1500 1/2 ton an silverado 2500 3/4 and up. same goes for gmc

Apr 06, 2013 | 1995 GMC Sonoma

1 Answer

I have a 2006 Savana GMC 1 ton van that the both front turn signal housings need to be replace, how do you remove and install the housing?

Take a large (1/4" or wider) flat tippped screwdriver and insert in the outside edge of lens and gently pry off, there is a a plastic tip that holds the lens into the grill housing, once it is loose then move forward and outward. The inside just has a tab that holds the lens in. Mike Thompson ASE Master Tech. Fleetwash Atlanta Shop Manager

Jul 26, 2011 | 2006 GMC Savana

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts


Level 3 Expert

76164 Answers


Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides