Question about Cars & Trucks

Open Question

Touch screen calibration fails - Cars & Trucks

Posted by on

  • Richard M.
    Richard M. Nov 06, 2012

    touch screen for what? Thank You

  • srinivasa Nov 06, 2012

    Sorry, this is navus gps installed in to my dodge caliber 2007 model, the gps is working but the touch screen do not respond at the point i touch rather it takes inputs an inch away from where i touch

×

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2007 checy impala read "calibration complete" what does that mean ????


CALIBRATION COMPLETE
Refer to Electronic Compass Calibration do you have an owners manual ?
Compass Calibration
The compass direction will show CAL if it needs to be calibrated. Before calibrating the compass, drive the vehicle to an area that is magnetically clean (free of large metallic objects).
  1. Turn ON the ignition.
  2. Before calibrating the compass, make sure the compass is set to the variance zone in which the vehicle is travelling. See Compass Magnetic Variation Adjustment below.
  3. Press the vehicle information button until the PRESS TO CALIBRATE COMPASS screen is displayed.
  4. Press the set/reset button to start the compass calibration.
  5. The DIC will display CALIBRATING: DRIVE IN CIRCLES. Drive the vehicle in circles at less than 8 km/h (5 mph) to complete the calibration. The DIC will display CALIBRATION COMPLETE when the calibration is complete.

Oct 02, 2016 | 2007 Chevrolet Impala

1 Answer

Prius mfd touch fail- how dismantle


Change the navigation display

Jun 29, 2014 | 2010 Toyota Prius

1 Answer

P0171 AND P0174B WHAT DOES IT MEAN?


Trouble Code: P0171

Fuel Trim System Lean (Bank 1)

Possible Causes:


Air leaks in intake manifold, exhaust pipes or exhaust manifold.Fuel control sensor is out of calibration (ECT, IAT or MAF.)Low fuel pressure (fuel filter clogged, pressure regulator failure).One or more injectors restricted or pressure regulator has failed.HO2S element is contaminated, deteriorated or has failed.Vacuum hose is disconnected, broken, leaking or loose.Trouble Code: P0174

Fuel Trim System Lean (Bank 2)

Possible Causes:


Air leaks in intake manifold, exhaust pipes or exhaust manifold.Fuel control sensor is out of calibration (ECT, IAT or MAF).Low fuel pressure (fuel filter clogged, pressure regulator failure).One or more injectors restricted or pressure regulator has failed.HO2S element is contaminated, deteriorated or has failed.Vacuum hose is disconnected, broken, leaking or loose.

Oct 24, 2012 | 1999 Chevrolet Express

1 Answer

Radio stations


There is a radio option to recalibrate your touch screen. Please press the following three hard keys simultaneously RADIO/MEDIA, SEEK UP, NAV (AUDIO on REN). Once you begin to recalibrate the touch screen you must finish. Audio confirmation prompts are provided for each of the three points of calibration, one beep for the first, two for the second and three for the third. The calibration needs to be precise as possible and a PDA stylus would be recommended. The MyGIG radio requires the user to repress each calibration point to confirm the calibration process. A green crosshair indicates proper calibration.You must not start with the "+" but with the "+1", then goto "+2" and last to "+". Repeat this until all crosses are green and exit with pushing the menue or any other key. Done

Jul 20, 2012 | 2008 Dodge Grand Caravan

1 Answer

Codes P700,P1121 and P0122



Trouble Code: P0122
Are you sure on p1121 or was it po121 because there is no p1121?
Throttle Position Sensor 'A' Circuit Low Input
Possible Causes:


TP sensor signal circuit is shorted to ground TP sensor VREF circuit is open or shorted to ground


Trouble Code: P0700

TCU Request For MIL -ON-
Possible Causes:


poor connection TCM


Trouble Code: P0121

Throttle Position Sensor Performance
Possible Causes:


MAF sensor or TP sensor ground circuit has high resistance MAF sensor has drifted out of calibration TP sensor has drifted out of calibration TP sensor is damaged or has failed PCM/ECMTP sensor is damaged or has failed PCM has failed

Jun 08, 2012 | 2003 Kia Sorento

1 Answer

Code PE 1259 for Honda Odyssey 1998


Trouble Code Conditions:DTC P0107, P0108, P0135, P0137, P0138, P0141, P1128, P1129 and P1259 not set, engine running in closed loop, and the PCM detected the LONGFT value exceeded the calibrated lean limit value
Possible Causes:
Air leaks in intake manifold, exhaust pipes or exhaust manifold One or more injectors restricted or pressure regulator has failed Air is being drawn in from leaks in gaskets or other seals O2S element is deteriorated or has failed A "fuel control" sensor is out of calibration (ECT, IAT or MAP)

May 31, 2011 | Honda Odyssey Cars & Trucks

1 Answer

Turned my Pontiac 2001 Aztec on and all lights started blinking. It released the trunk, and even blew the horn without touching it. The "security" light and "service engine soon" comes on. The car has...


you need to find out what cause this because it sound as if someone was trying to get into your car and the alarm is set give these websites a try www.alldatadiy.com and www.autozone.com if all fails stop in at your local GM dealership and talk with the service manger he or she will be able to help you wish you the best of luck Michigan Man.

Mar 22, 2010 | 2001 Pontiac Aztek

1 Answer

Compass calibration


im taking an educated guess- ive done it maybe once or twice in a chrysler- try to go into the MENU by hitting the buttons for menu and reset. if u luck out it will say something like calibrate or calibrate compass on the screen. now it will either tell u what to do or if not drive carefully in a small circle slowly clockwise and then counterclockwise several times. as youre doing this it might suddenly pop up "calibration complete" or something similar. i almost forgot- IF U HAVE THE OWNERS MANUAL ,LOOK IN THERE 1ST. if not try what i said.

Aug 09, 2009 | 1991 Pontiac Grand Prix

2 Answers

Toyota 2008 Prius Touch-Screen


Problem is resolved, 
I pulled & giggled a couple of fuses, found one fuse that had an extend fuse container was probably not quite seated right. Will notify dealer & replace several working fuses with new. rr 

Mar 19, 2009 | 2008 Toyota Prius

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...