Question about Cars & Trucks

Open Question

HONDA ACTIVA REAR WHEEL REMOVAL PROCEDURE - Cars & Trucks

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 119 Answers

SOURCE: Procedure for replacing rear wheel bearings 2000 Forester

i'm assuming you don't have a hubshark,this is a tool that will alllow you to remove the bearing while the knuckle is attached to the car,you may be able to rent this tool at a auto prts store .if not you need to remove the entie knuckle,first remove the trailing arm bolt,then the lateral link bolt{long and stubborn bolt},disassemble the brake shoes and parking brake cable,abs sensor if equipped the knuckle to strut bolt{no marking necessary they are not eccentric} then you need a to use or borrow a press to remove hub and bearings good luck

Posted on Jul 26, 2009

Ad
CMR_Racing
  • 24 Answers

SOURCE: front wheel bearing removal and installation 1996 civic

http://honda-tech.com/showthread.php?t=2517273 go to this site it has a step by step including pics

Posted on Dec 13, 2009

  • 1212 Answers

SOURCE: X TYPE REAR WHEEL REMOVAL

if all lugnuts are removed, it is corrosion between the hub and centering hole of the wheel. Make sure vehicle is properly supported and kick tire on one side-sidewall. this should dislodge it or at least ger it in a position where you can rock the tire and wheel assembly on the hub enough to work it off of the hub. If one kick does not dislofge it try again on opposite side.

Once off, clean up the mating surfaces and the centering hole of the wheel and apply some axle grease around the back side of wheel and the centering hole. Do not use too much or it may get thrown onto tire or onto the rotor surfaces.

Since one stuck, you should check them all.

Posted on Jun 28, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 Honda CRV, how to remove rear axle shaft


REMOVAL & INSTALLATION

  1. Loosen the wheel nuts.
  2. Carefully raise the locking tab of the axle spindle nut using a hammer and chisel.
  3. Loosen and remove the axle nut.
  4. Raise and safely support the vehicle.
  5. Remove the rear wheel.
  6. Remove the halfshafts from the differential. Refer to the differential removal procedure in this section for specific details.
  7. Carefully remove the halfshaft from the trailing arm assembly by tapping on it with a plastic hammer, or using a suitable drift and hammer.
To install:
    Installation is the reverse of removal taking note of the following points:

    • Install new set rings in the groove of the splined inner CV-joint shafts.
    • Top off the differential fluid as necessary.
    • Install a new spindle nut and torque to 134 ft. lbs. (181 Nm), and once tightened, stake the nut.
    • Tighten the wheel nuts to 80 ft. lbs. (108 Nm).

Dec 10, 2015 | Honda Cars & Trucks

1 Answer

Rear axle removal 98 gmc 2500 four wheel drive


the 2500 had two different axle housing the hd version had bolts in the center of the wheel under the hub cap the light duty you need to remove the cover in the center of the housing in the middle of the rear end then remove the 5/16 bolt the holds the center pin in the diff case then push the axle in and remove the large c clip then the axle shaft will pull out

Jun 30, 2012 | Cars & Trucks

1 Answer

How to change back hub on 97 cr-v


Rear Brake Discs
  • Fotolia.com" data-type="modal">honda-rear-wheel-bearing-removal-1.1-800x800.jpg Replace the bearing and race as a single set. automotive roller bearing. image by Tom Oliveira from Fotolia.com

    Before raising the rear of your Honda, remove the dust cup from the center of the brake drums using a hammer and chisel. This will give you access to the spindle nut, which you can loosen using an axle nut socket. Then you can raise and remove the wheel/tire assembly ,or assemblies if you are replacing the bearings on both wheels.

    If your Honda model is equipped with rear disc brakes, remove the brake disc retaining screws, the brake hose bracket from the steering knuckle and caliper bracket mounting bolts. Hang the caliper to the coil spring using wire. Do not let the caliper hang free or the brake hose may be damaged.

    At this point, you will be able to remove the brake disc by hand. However, rust may have a firm grip on the disc. If this is the case, use a couple of 8-by-1.25 mm bolts and screw them evenly into the brake disc threaded holes. This will push the disc off the hub. Now you can finish removing the spindle nut and hub/wheel bearing assembly and install the new hub/wheel bearing assembly using a new spindle nut



Read more: Honda Rear Wheel Bearing Removal ' eHow.com http://www.ehow.com/way_5974291_honda-rear-wheel-bearing-removal.html#ixzz1W3WDRoqv Rear Brake Drums
  • Fotolia.com" data-type="modal">honda-rear-wheel-bearing-removal-2.1-800x800.jpg Pack the bearing with bearing grease before installation. roller bearing image by Tom Oliveira from Fotolia.com

    If your Honda Civic comes equipped with rear brake drums, remove the center grease cup and loosen the axle spindle nut using an axle nut socket. After raising and removing the wheel/tire assembly, finish removing the axle nut and washer.

    You might be able to remove the outer wheel bearing from the spindle using a screwdriver. If not, wiggle the brake drum as you pull on it to let the bearing fall off the spindle. However, the brake drum might be caught in place by the brake shoes. In this case, you can retract the brake shoes through the hole in the back of the backing plate.

    Remove the rubber plug from the back of the backing plate. Then rotate the star wheel on the adjusting screw using a brake adjusting tool as you push the lever off the start wheel with a screwdriver. With the brake shoes off the brake drum, pull the brake drum off the wheel assembly. Then clean the brake assembly with brake parts cleaner and a clean, lint-free towel.

    Now you can set the brake drum on a workbench or hard surface and remove the grease seal and inner wheel bearing. The inner and outer wheel-bearing races can be removed using a drift punch and hammer. Pack the new wheel bearings with high-temperature wheel-bearing grease using a wheel-bearing packer and use a new grease seal during installation. Also, before reinstalling the brake drum, apply a thick coat of wheel-bearing grease to the cavity inside the hub, but do not fill it completely.



Read more: Honda Rear Wheel Bearing Removal ' eHow.com http://www.ehow.com/way_5974291_honda-rear-wheel-bearing-removal.html#ixzz1W3WN9eBb

Aug 25, 2011 | Honda CR-V Cars & Trucks

1 Answer

Can you help me dis-assemble my front bumper honda odyssey 1999 ?


Front
  1. Note the radio security code, then disconnect the negative battery cable.
  2. Remove the bolt from the lower part of the bumper just in front of the wheel opening, and remove the self-tapping screw from the rear most portion of the bumper at the forward portion of the front wheel well.
  3. On V6 Odyssey models, perform the following:
    • Remove the grille.
    • Remove the pins and clips from the lower front of the bumper.
  4. On 4-cylinder Odyssey models, remove the bolts from the left and right side lower brackets for the bumper at the ends of the lower air intake.
  5. Pull the ends of the bumper outward.
  6. Have an assistant help guide the bumper up and away from the vehicle.
  7. Installation is the reverse of the removal procedure.

Mar 06, 2010 | Honda Odyssey Cars & Trucks

1 Answer

I have a 2002 Lincoln ls . How do I replace the abs speed sensor? Right front tire?


you have one on the inside of each wheel.
SECTION 206-09A: Anti-Lock Control 2002 Lincoln LS Workshop Manual
REMOVAL AND INSTALLATION Front Wheel Speed Sensor
Material Item Specification RTV Silicone Sealant
FSTZ-19G204-AB (Canada CXC-114A) NAVSTR Sealer
Removal and Installation
  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Position the inner splash shield aside.
    1. Remove the pin-type retainers.
    1. Position the inner splash shield aside.
  1. Disconnect the anti-lock brake sensor electrical connector.
  1. Remove the anti-lock brake sensor harness from the brake hose clips.
  1. Remove the anti-lock brake sensor.
    1. Remove the anti-lock brake sensor clip.
    1. Remove the anti-lock brake sensor.
  1. NOTE: Make sure the anti-lock brake sensor is fully seated before installation of the new clip.
    To install, reverse the removal procedure.
    • Apply a 2.5 mm (0.1 in) bead of silicone sealant to the outside diameter of the anti-lock brake sensor.
-------------------------------------------------------------------------
Rear Wheel Speed Sensor Removal and Installation
  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Disconnect the rear anti-lock brake sensor electrical connector.
  1. Remove the rear anti-lock brake sensor harness from the control arm clips.
  1. NOTE: Clean off dirt and foreign material that may have collected around the rear anti-lock brake sensor before removal.
    Remove the rear anti-lock brake sensor.
    1. Remove the anti-lock brake sensor bolt.
    1. Remove the anti-lock brake sensor.
  1. To install, reverse the removal procedure.

Feb 24, 2010 | 2001 Lincoln LS

2 Answers

How to replace rear wheel bearings


don't have topaz. maybe escort will help guide you.

Section 04-02: Suspension and Wheel Hubs, Rear 1996 Escort, Tracer Workshop Manual
REMOVAL AND INSTALLATION Wheel Bearing and Hub Assembly NOTE: Wheel bearings are not serviceable and should therefore be replaced as an assembly with the wheel hub (1104).

Removal
  1. Raise and support the vehicle.
  1. Remove the wheel and tire assembly.
  1. Remove the hub grease cap (1131) from the wheel hub.
  1. If equipped with disc brakes, remove the rear disc brake caliper (2552) and rear disc brake rotor (2C026). Refer to Section 06-04 for the removal procedure.
  1. If equipped with drum brakes, remove the two brake drum screws and the brake drum (1126).
  1. Unstake the rear axle wheel hub retainer (4B477) securing the wheel hub to the rear wheel spindle (4A013). Remove and discard the rear axle wheel hub retainer.
  2. Remove the wheel hub from the rear wheel spindle.

Feb 06, 2010 | 1990 Mercury Topaz

1 Answer

Corvette sway bar installation


Stabilizer Bar: Service and Repair
Front
Removal Procedure
1. Raise and support the vehicle. Refer to Vehicle Lifting.
2. Remove the tire and wheel assemblies. Refer to Tire and Wheel Removal and Installation.
3. Remove the stabilizer shaft link nuts from the stabilizer shaft.
4. Remove the stabilizer shaft insulator clamps from the front crossmember.
5. Remove the stabilizer shaft from the vehicle.
Installation Procedure
1. Install the stabilizer shaft, insulator clamps and bolts to the crossmember.
2. Install the stabilizer shaft links to the stabilizer shaft.
Notice: Refer to Fastener Notice in Service Precautions.
3. Install the stabilizer shaft link nuts.
- Tighten the stabilizer shaft link nuts to 72 Nm (53 ft. lbs.).
4. Install the stabilizer shaft insulator clamp bolts.
- Tighten the stabilizer shaft insulator clamp bolts to 58 Nm (43 ft. lbs.).
5. Install the tire and wheel assemblies. Refer to Tire and Wheel Removal and Installation.
6. Lower the vehicle.



Stabilizer Bar: Service and Repair
Rear
Removal Procedure
1. Raise and support the vehicle. Refer to Vehicle Lifting.
2. Remove the tire and wheel assemblies. Refer to Tire and Wheel Removal and Installation.
3. Remove the stabilizer shaft link nuts from the stabilizer shaft.
4. Remove the stabilizer shaft clamps, bolts and nuts retaining the shaft to the crossmember.
5. Remove the stabilizer shaft from the vehicle.
Installation Procedure
1. Install the stabilizer shaft to the vehicle.
Notice: Refer to Fastener Notice in Service Precautions.
2. Install the stabilizer shaft insulator clamps to the stabilizer shaft and the crossmember.
- Tighten the stabilizer shaft insulator clamp bolts to 65 Nm (49 ft. lbs.).
- Tighten the stabilizer shaft insulator clamp nuts to 95 Nm (70 ft. lbs.).
3. Install the stabilizer shaft links to the stabilizer shaft.
- Tighten the stabilizer shaft link nuts to 72 Nm (53 ft. lbs.).
4. Install the tire and wheel assemblies. Refer to Tire and Wheel Removal and Installation.
5. Lower the vehicle.


Oct 30, 2009 | 2001 Chevrolet Corvette

1 Answer

Rear axle bearing replacement



REAR WHEEL BEARING/ HUB

Removal Procedure
  1. Raise the vehicle. Refer to Vehicle Lifting in General Diagnosis.
  2. Remove the wheel and the tire. Refer to Tire and Wheel Removal and Installation in Wheels, Tires and Alignment.
    1. Remove and support the brake caliper. Refer to Brake Caliper Replacement (Front) or Brake Caliper Replacement (Rear) in Brakes.
    2. Remove the brake rotor. Refer to Brake Rotor Replacement in Disc Brakes.
    3. Remove the ABS sensor wire connector.
    4. Remove the four bolts from the control arm.
    5. Remove the hub and bearing from the control arm.
    6. Remove the brake shield from the control arm.
    7. Clean the control arm face and the bore before installing the hub and the bearing.
    Installation Procedure

    Notice: Refer to Fastener Notice in Service Precautions.
    1. Install the brake shield and the hub and the bearing to the control arm with the four bolts. Be careful not to drop the hub and the bearing, as it could be damaged. Reconnect the ABS sensor. Tighten the hub and bearing bolts to 70 Nm (52 ft. lbs.).
    2. Install the brake rotor. Refer to Brake Rotor Replacement in Disc Brakes.
    3. Install the brake caliper. Refer to Brake Caliper Replacement (Front) or Brake Caliper Replacement (Rear) in Disc Brakes.
    4. Install the wheel and the tire. Refer to Tire and Wheel Removal and Installation in Wheels, Tires and Alignment. Tighten the wheel nuts to 140 Nm (100 ft. lbs.).
    5. Lower the vehicle.

Feb 14, 2009 | 2002 Pontiac Bonneville

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

163 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...