Question about Cars & Trucks

Open Question

Removing front bumper off a lancer ce - Cars & Trucks

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

stevenhurc
  • 450 Answers

SOURCE: need to replace heater core in 2003 CE lancer.

very large job by the look of it, can download workshop manual from pdftown.com
degas air cond, drop coolant, remove dash, reomve front seats, remove console, remove heater and evaporator case assembly then get to replace heater core.
as i said big job.

Posted on Jun 21, 2009

  • 10865 Answers

SOURCE: front bumper removal

all you have to do is unbolt it. if the nuts won't budge spray them with wd40 and wait over night for that product to loosen up the rust.

Posted on Sep 14, 2009

  • 2 Answers

SOURCE: removal of front bumper

The bumper is secured using four 13mm nuts.

a) Open the bonnet and look for one 13mm nut on the lower inside of each headlight.
b) Remove the towing eye covers on the lower section of the bumper and you will find one 13mm nut in each.

Hope this helps.
Shane

Posted on Apr 09, 2010

skychief2001
  • 21873 Answers

SOURCE: cant find spark plugs on 97 ce lancer

Each plug should be under a coil - you may have to remove a plate in the center of the valve cover to access them.

Posted on Aug 12, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i change to hood release cable on the ck2 lancer


With some difficulty ... the cable runs inside the front inner guard box section down to the firewall and into the cabin. You will likely have to remove the LHS headlamp, quarter light, disconnect the front bumper cover from the guard panel, and then remove the guard panel.

Jan 07, 2015 | 1998 Mitsubishi Lancer

1 Answer

How to remove the front bumper"?"


To remove you will have to use air tools as it cuts the time to minutes instead of hours. Remove front tires and unplug lights in fiberglass bumper. Then remove all the screws and remove fiberglass .bumper. I will supply and DIY email address so you can follow step by step. Subaru wrx sti remove bumper TUTORIAL DIY

May 06, 2014 | 2006 Subaru Legacy

1 Answer

Cant find spark plugs on 97 ce lancer


Each plug should be under a coil - you may have to remove a plate in the center of the valve cover to access them.

Aug 11, 2012 | Mitsubishi Lancer Cars & Trucks

1 Answer

Can you help me dis-assemble my front bumper honda odyssey 1999 ?


Front
  1. Note the radio security code, then disconnect the negative battery cable.
  2. Remove the bolt from the lower part of the bumper just in front of the wheel opening, and remove the self-tapping screw from the rear most portion of the bumper at the forward portion of the front wheel well.
  3. On V6 Odyssey models, perform the following:
    • Remove the grille.
    • Remove the pins and clips from the lower front of the bumper.
  4. On 4-cylinder Odyssey models, remove the bolts from the left and right side lower brackets for the bumper at the ends of the lower air intake.
  5. Pull the ends of the bumper outward.
  6. Have an assistant help guide the bumper up and away from the vehicle.
  7. Installation is the reverse of the removal procedure.

Mar 06, 2010 | Honda Odyssey Cars & Trucks

1 Answer

How you take off the front bumber


have 96, 95 similar

Section 01-19: Bumpers 1996 Villager Workshop Manual
REMOVAL AND INSTALLATION Bumper and Bumper Cover Front
Removal
  1. Raise and support the vehicle.
  1. Remove the RH and LH front wheel (1007).
  1. Remove the RH and LH front fender splash shield screws. Remove the RH and LH front fender splash shields (16102).




  1. Remove the four front fender brace screws.




  1. Remove the two front fender brace nuts.
  1. Remove the two plastic screws.
  1. Remove the seven clip buttons located under the front bumper cover (17D957).




  1. Remove the RH and LH front turn signal lamps (13369). Refer to Section 17-01 for the removal procedure.
  1. Remove the four front bumper cover brace bolts.




  1. Remove the front bumper cover from the vehicle.




  1. Remove the two front turn signal lamp wire harnesses from the front bumper (17757).



  2. Remove the eight front bumper bolts.




  1. Remove the front bumper from the vehicle.

Mar 02, 2010 | 1995 Mercury Villager

1 Answer

Need to replace heater core in 2003 CE lancer. require assistance with removal procedure/method


very large job by the look of it, can download workshop manual from pdftown.com
degas air cond, drop coolant, remove dash, reomve front seats, remove console, remove heater and evaporator case assembly then get to replace heater core.
as i said big job.

Jun 21, 2009 | 2002 Mitsubishi Lancer

1 Answer

How to remove the headlight off an 06 lancer es 4 dr?


yes remove the front bumper and u will see the obvious bolts and brackets to remove the assemblies, just a few bolts that hold them in place.

Apr 08, 2009 | 2006 Mitsubishi Lancer

1 Answer

Which fuse is for brake lights for ce lancer 98 coupe


just go through them all one by one until you find the fuse

Mar 26, 2009 | Mitsubishi Lancer Cars & Trucks

2 Answers

Instrument failure lancer 2001mitsubishi coupe


On my Bitsasushi Lancer CE 2000 i found a Hairline crack on Vinyl PCP about 6 o'clock when viewing Cluster right way up at rear where Vinyl circuit folds over under plastic Tabs, looks like power supply to Warning Lights, i just Spent 5 mins scraping Blue Vinyl to reveal Crack a Dab of Solder a Dollop of clear Laquer(Naily-Polish) inserted Cluster

Oct 26, 2008 | 2002 Mitsubishi Lancer

1 Answer

Replace the face skid in the front bumper


remove front bumper and it should be clear what holding the face skid in place

Sep 29, 2008 | 2008 Honda Pilot

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

143 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...