Question about 1999 Oldsmobile Alero

1 Answer

1999 Oldsmobile Alero 2.4L.

What is the torque in lbs for the head bolts?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 239 Answers

75-85 lb

Posted on Jan 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rocker arm pivot torque for olds cutlass 1987 307


Oldsmobile Torque Specs - GbodyOlds.com

www.gbodyolds.com/forum/showthread.php?754-Oldsmobile-Torque...
Feb 7, 2013 - 2 posts - ‎2 authors Oldsmobile Small-Block Engines Cylinder Head Bolts (1/2in. bolt) 130 ft. lbs. Cylinder Head ... Rocker Arm Pivot Bolt 25 ft. lbs. Rod Bearing ...

Rocker Arms - AutoZone

www.autozone.com/...Cutlass...1987.../Rocker-Arms/_/P-0900...

AutoZoneGM Cutlass RWD 1970-1987 Repair Guide ... To remove the rocker arms from the shaft, the nylon arm retainers must be removed. ... 7: Engine valve system, 260, 307, 350, 403 Oldsmobile built engines ... Unfasten the two bolts that attach the rocker arm pivot to the cylinder head. ... Torque the retaining bolts to 25 ft. lbs.

Dec 01, 2015 | 1987 Oldsmobile Cutlass Salon

1 Answer

I'm installing a 2.2 in a 2003 Oldsmobile Alero and I'd like to know the torque specs on the Exhaust bolts and studs. Thanks


Exhaust Manifold To Cylinder Head - 9.58 ft lbs
Exhaust Pipe To Exhaust Manifold - 20 ft lbs
you can check it out here, also all other torque specs for your engine.
Torque Specs Database

Feb 23, 2015 | 2003 Oldsmobile Alero

1 Answer

Can you tell me torque requirement for intake manifold bolts on a 1999 Alero V6?


upper intake bolts torque is 18 ft lbs - lower intake bolts torque is 115 inch lbs.

Sep 21, 2011 | 1999 Oldsmobile Alero

1 Answer

What is the torque number sequence for a 2001 oldsmobile aurora 3.5 v6


Assuming about cylinder head...

zjlimited_947.jpg

Fig. Front cylinder head bolt torque sequence - 3.5L (VIN H) engine
  1. Install the cylinder head with a new gasket.
  2. Install new M11 bolts and M6 bolts.
  3. Torque the M11 bolts in sequence to:
    1. Step 1: 30 ft. lbs. (40 Nm).
    2. Step 2: 100 degree turn.
    3. Step 3: 100 degree turn.

  4. Torque the long M6 bolt to 22 ft. lbs. (30 Nm).
  5. Torque both shorter M6 bolts to 106 inch lbs. (12 Nm).
  6. Install or connect the following:
    Lifters Rocker arms Camshafts Primary chain
  7. Remove the timing chain holding tool.
  8. Install or connect the following:
    Camshaft covers. Torque the bolts to 80 inch lbs. (9 Nm). Exhaust manifold. Torque the bolts to 22 ft. lbs. (30 Nm). Coolant crossover pipe. Torque the bolts to 18 ft. lbs. (25 Nm). Intake manifold. Torque the bolts to 62 inch lbs. (7 Nm). New oil filter Negative battery cable

Hope helps.

Mar 29, 2011 | 2001 Oldsmobile Aurora

1 Answer

Crankshaft torque specs 2.4L


2.4L MAIN BEARING TORQUE IS 15 FT LBS PLUS 90 DEGREES ***** ROD BEARING TORQUE IS 18 FT LBS PLUS 80 DEGREES CRANKSHAFT PULLEY BOLT 129 FT LBS PLUS 90 DEGREES.

Sep 22, 2010 | 1999 Oldsmobile Alero

2 Answers

Torque spec on 99 olds alaro 3.4 head bolts


HEAD TORQUE SPEC IS 37 FT LBS ROTATE AN ADDITIONAL 90 DEGREES 1/4 TURN.

Aug 16, 2010 | 1999 Oldsmobile Alero

2 Answers

Torque specification on a 2003 alero cylinder heads 3.4 liter


3.4L Engine To Remove:
  1. Remove the lower intake manifold.
  2. Remove the exhaust crossover pipe.
  3. If removing the right cylinder head, remove the catalytic converter from exhaust manifold.
  4. If removing the left cylinder head, remove the engine oil dipstick and tube.
  5. Remove the rocker arms and pushrods.
  6. Remove and discard the cylinder head bolts.
  7. Remove the cylinder head.
  8. Clean the mating surfaces on the following items:
    • Cylinder head
    • Cylinder block
    • Intake manifold
  9. Clean the cylinder block bolt threads.
NOTE: During disassembly, keep the valve train components together for proper location during assembly.
To Install:
NOTE: Coat the cylinder head bolt threads using thread sealer.
  1. If removed, install the following components:
    • Exhaust manifold
    • Accessory studs
    • Spark plugs
  2. Place the cylinder head gasket in position over the dowel pins. Ensure that the THIS SIDE UP note is showing.
  3. Install the cylinder head. Cylinder head torque sequence ’99-‘00 gmpc_v6_14.gif

    Cylinder head torque sequence ’01-05 gm-03-34-682.gif

  4. Install the new cylinder head bolts.
    • Tighten the cylinder head bolts a first pass to 44 ft lb (60 Nm).
  5. Tighten the cylinder head bolts in sequence an additional 95 degrees.
  6. Install the intake gasket.
  7. Install the pushrods and rocker arms.
  8. Raise and support the vehicle.
  9. Install the catalytic converter and dipstick tube and indicator if removed.
  10. Lower the vehicle.
  11. Install the exhaust crossover pipe.
  12. Install the intake manifolds.
  13. Connect negative battery cable.
  14. Fill the cooling system.

Jul 03, 2010 | 2003 Oldsmobile Alero

1 Answer

Head tourqe specs for 403 olds and bolt tightening


Fig. : Cylinder head torque sequence, 260, 307, 350 403 Oldsmobile built engines

5c04c01.jpg


On the V8, tighten the bolts, in the sequence illustrated, to 100 ft. lbs. When all bolts have been tightened to this figure, begin the tightening sequence again, and torque all bolts to 130 ft. lbs.

On V6's, tighten all head bolts in sequence to the following torques:
* All except bolts 5, 6, 11, 12, 13 and 14 - 100 ft. lbs.(19-135.5 Nm)
* Bolts 5, 6, 11, 12, 13, and 14 - 41 ft. lbs. (19-55.5 Nm)
* All bolts except 5, 6, 11, 12, 13, and 14 - 142 ft. lbs. (19-192.5 Nm)
* Bolts 5, 6, 11, 12, 13, and 14 - 59 ft. lbs. (19-80 Nm)

9fb545e.jpg

Hope this help (remember comment and rated this).

Mar 29, 2010 | 1984 Oldsmobile Cutlass

1 Answer

How do you replace a rear passenger side torison bar on an oldsmoblie alero 1999


SAFELY RAISE AND SUPPORT REAR OF CAR ON JACK STANDS. REMOVE THE TORSION BAR TO KNUCKLE BOLT WASHER AND BUSHING.REMOVE TORSION BAR TO CHASSIS BOLT.REMOVE BAR FROM THE CHASSIS.TO INSTALL.INSTALL TORSION BAR TO THE CHASSIS TORQUE THE NUT / BOLT TO 48 FT LBS.PLUS ADDITIONAL 120 DEGREE TURN.TORSION BAR TO THE KNUCKLE TORQUE THE BOLT TO 51 FT LBS.

Sep 24, 2009 | 1999 Oldsmobile Alero

Not finding what you are looking for?
1999 Oldsmobile Alero Logo

Related Topics:

107 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

61292 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...