Question about 2007 Toyota Tundra

Open Question

What is causing the right front turn signal bulb to keep burning out

I have replaced the bulb 3 times - the last time it went bad after driving for approximately 30 minutes

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
CRTN
  • 716 Answers

SOURCE: 2008 Camry Front Turn signal Bulb

Front Open The Hood And View Back Of Headlight Turn And Then Pull Light.
Rear Open Trunk And Remove Carpet From Behind Light Now You Can View The Bulb Housing Turn And Pull.

Posted on Jan 07, 2009

Ad
  • 496 Answers

SOURCE: 91 toyota corolla left turn signal stays lit up al

If the right side signals are working properly and you can hear the signal flasher clicking when the right side signals are selected, the flasher is not the problem. Its more likely you have a short to ground in the left side wiring somewhere.

Posted on Feb 21, 2009

mkv0525
  • 358 Answers

SOURCE: 2003 4Runner Electrical problems - Door Lock and Rght Turn Signal

needs new light socket. common problem.

Posted on May 20, 2009

  • 1632 Answers

SOURCE: 2001 Toyota Tacoma- turn lights not working and cruise control

fuses???
Check relays.....
Harness grounds, engine ground,
Check the trailer harnes for short.
Vitally

Posted on Jun 02, 2009

  • 5 Answers

SOURCE: Rear right turn signal does not work.

check the front right bulb

Posted on Sep 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Both Headlights are not working, just changed them a couple months ago, what could be the problem?


Because you have given absolutely no details I am forced to guess as to your situation. The big factors are, what type of bulb did you get, how often do drive and is your car new enough that the lights come on even during the day?
Super bright bulbs are nice but they tend to burn out faster than normal bulbs. They claim to be good for about a year. How Long Should Car Light Bulbs Last But for some reason, a lot of companies consider that the average car only gets used for 12,000 km per year. if you drive double that, your headlights may only last half as long. Is you headlights on all the time or do you do a lot of night driving, it all affects how long the lights last.
Maybe you should check out these
http://www.candlepowerinc.com/pdfs/LL_Headlamp.pdf
or this
https://www.powerbulbs.com/ca/product/philips-eco-vision-h7-car-headlight-bulbs

Mar 03, 2017 | Cars & Trucks

1 Answer

My 2007 Cadillac STS is in theft mode, how do I release theft mode? f


Maybe this?

30-Minute Relearn Procedure

1. Press and hold the OFF/Acc button for approximately 4 seconds to turn the ignition ON, with the engine OFF.
2. Observe the Security indicator. After approximately 10 minutes the indicator will turn off.
3. Turn OFF the ignition, and wait 5 seconds.
4. Repeat steps 1-3 two more times for a total of 3 cycles or 30 minutes.

Important: The vehicle learns the password on the transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle.

5. Start the vehicle. The module being programmed has now learned the RCDLR password.

Sep 22, 2015 | Cadillac Cars & Trucks

1 Answer

I have a 2005 Chrysler town and country. I went to put my foot on the brake to put it into drive and my speedometer gas and everything went blank and the park drive reverse neutral and all that went out...


I would pull the rear brake light bulbs and top 3rd brake light wire first to check for a shorted bulb.Do you have trailer wiring?That can be a source of shorts too.Next would be a "short tester" be used on the brake light wiring.

Jul 09, 2017 | Cars & Trucks

1 Answer

Both low beam headlights are out bulbs have been recently replaced several times and driver side connection. They went out breifly a few months ago as we were driving and came back on in a few minutes


sounds like the switch assembly on the actually column ( what you use to turn the headlights on and off) may have went bad! and or the relay for the headlights. my money would be on the dimmer switch though considering the highbeam and lowbeam are 2 different circuits. thats if both the bulbs have been checked and found good as you say. good luck

Sep 09, 2011 | Chevrolet TrailBlazer Cars & Trucks

1 Answer

I took my battery out of my 2005 corvette for winter storage - My digital message says Power Reduction - I was told this was due to the security system and followed the reset for a 2007 : it didn't...


All three parts must match. The key, the ignition, and the tdm. If you replaced with a different one, and they dont match, it will never work correctly again.

Apr 10, 2011 | 2005 Chevrolet Corvette

1 Answer

My truck use to start first click went to start it the other day runs for a few seconds then shuts down security code seems to be locked need to know how to bipass


Your Passlock may need to relearn the ignition keys, if the ignition lock has gone bad like my in-laws Grand Am Gt, here is what i did so they will not get stranded any more. Buy a Passlock by pass module for around $70.00. You can order one from GMPASSLOCK.COM in the mean time try resetting the Passlock. Good luck

Ignition keys relearn takes about 30 min to do. 30-Minute Learn Procedure
1.) Turn ON the ignition, with the engine OFF.
2.) Attempt to start the engine, then release the key to ON; the vehicle will not start.
3.) Observe the SECURITY tell tale light. After approximately 10 minutes, the light will turn OFF.
4.) Turn OFF the ignition switch, and wait 5 seconds.
5.) Repeat steps 1 through 4 - two more times - for a total of 3 cycles of 10 minutes. 3x10 = 30 minutes.
The vehicle is now ready to relearn the Passlock Sensor Data Code and/or passwords on the next ignition switch turn from OFF to CRANK Important: Turn the Ignition Switch OFF. The vehicle learns the Passlock Sensor Data Code and/or password on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle.
6.) Start the engine. The vehicle has now learned the Passlock Sensor Data Code and/or password.
7.) With a scan tool, clear any DTCs if needed. History DTCs will self clear after 100 ignition cycles.

Without a scan tool you may have momentary starter interruptions while history clears itself.

Jan 21, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

I replace ignition in a 2000 chevy impala. i need to know how to progam it work with the passlock II anti-theft


If you just replaced the ignition switch then there are no additional procedures.The vehicle should start.If you replaced the ignition lock cylinder then you have the do a relearn.This is done by 1.attempt to start the vehicle.The vehicle will not start when key is released.Do not turn the key off after releasing it just leave it in the run position.The security light will come on for approximately 10 minutes then go off.Turn off the ignition and wait 5 seconds then repeat this two more times.For a total of 30 minutes.After the last time when you go to start it it will learn the pass code.Make sure you turn the ignition off after the last 10 minutes and wait 5 seconds before attempting to start the vehicle.The vehicle should now start and run.If not retry from the top. Hope this helps.Good luck.

Dec 28, 2009 | 2000 Chevrolet Impala

1 Answer

2005 Hummer H2 battery went down and when I replaced it the alarm keeps going off and it will not start.


if it is the factory alarm you will have to do a relearn. G.M. uses a couple different ways to do the relearn and I would think it would be the same for hummer. turn off all acc and then turn the key to the on position wait 10 minutes you will see the light on the dash flash and go out . asap turn the key to off to on 3 times quickly and the third time leave it on on again do this 3 times for 30 minutes then after the final turning of the key 3 times on the 4th time start the car. so turn off all acc like radio , a/c ect then turn key to on in 10 minutes the light on dash will flash and go out quickly turn key from off to on 3 times and once again leave on on do that 3x for 30 minutes then start the car. that is the gm relearn for security they have one on some models that start after 10 minutes but that is usualy on the cheaper cars so just do the 30 minute.

Jun 04, 2009 | 2006 Hummer H3

4 Answers

Can't start my 1998 3.1 Monte Carlo


You have a Pass lock problem. There are 3 wires from the Ignition switch that reads the ignition key, if you have lot's of other keys on your key chain. That puts extra stress on the ignition lock switch, which in turns wear out the wires in the lock that reads the key.
The dealer will cost over $500.00 to replace the lock and key's to match. I got a good friend at a lock smith to over ride the system by running a diode across the 3 wires, but now i have no pass lock.
Try this, it might help if the wires are ok, it's to reset the pass lock that the dealer will try and still charge you hundred of dollars since they want to change the lock and key's for you.
Good luck and hope this helps: The relearn process is pretty simple and will take 30 minutes, if it'll work for you at all since your problem doesn't sound like a computer issue.

30-Minute Learn Procedure
1. Turn ON the ignition, with the engine OFF.
2. Attempt to start the engine, then release the key to ON; the vehicle will not start.
3. Observe the SECURITY tell tale light. After approximately 10 minutes, the light will turn OFF.
4. Turn OFF the ignition switch, and wait 5 seconds.
5. Repeat steps 1 through 4 - two more times - for a total of 3 cycles of 10 minutes. 3x10 = 30 minutes.
The vehicle is now ready to relearn the Passlock Sensor Data Code and/or passwords on the next ignition switch turn from OFF to Crank.

Important:
Turn the Ignition Switch OFF.
The vehicle learns the Passlock Sensor Data Code and/or password on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle.
6. Start the engine. The vehicle has now learned the Passlock Sensor Data Code and/or password.
7. With a scan tool, clear any DTCs if needed. History DTCs will self clear after 100 ignition cycles.
Without a scan tool you may have momentary starter interruptions while history clears itself.







May 25, 2009 | 2006 Chevrolet Equinox

2 Answers

2001 chevolet cavilier brake lights & blinkers burning up


sounds like you put a 21 watt bulb in place of a 6 watt bulb ,or you have put single pole bulb in place of a double filament,double pole bulb

Feb 02, 2009 | 2001 Chevrolet Cavalier

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

758 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...