Question about 2002 Ford Taurus

Open Question

Replace water pump on 2002 taurus - 2002 Ford Taurus

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
c17hydro
  • 2984 Answers

SOURCE: 2002 ford taurus wtaer pump

Removal & Installation 3.0L (2V) To Remove:

  1. Drain the engine cooling system.
  2. Loosen the water pump pulley.
  3. Remove the bolt and the nut and position the roll restrictor bracket out of the way.
  4. Remove the accessory drive belt.
  5. Remove the generator.
  6. Remove the bolt and the accessory drive belt tensioner.
  7. Remove the nut, the bolt and the support bracket.
  8. Remove the bolts and the water pump pulley.
  9. Disconnect the water pump inlet hose and the crankshaft position sensor electrical connector.
  10. Remove the bolts and the water pump, and clean the sealing surfaces
To Install:
  1. Install the water pump. Tighten bolts in the sequence shown:
    1. Tighten numbers 1-7 to 18 ft.-lbs. (25 Nm)
    2. Tighten numbers 8-12 to 89 in.-lbs. (10 Nm)
    3. Connect the crankshaft position sensor electrical connector and the water pump inlet hose
    4. Install the support bracket.
    5. Install the accessory drive shaft tensioner.
    6. Install the generator.
    7. Install the roll restrictor bracket, bolt and the nut.
    8. Install the water pump pulley.
    9. Install the accessory drive belt.
    10. Connect the battery ground cable.
    11. Fill the engine cooling system.

9de9feb.gif
Water pump bolt torque sequence (3.0L (2V) engine)

Posted on Jul 04, 2009

Ad
  • 213 Answers

SOURCE: How many hours will it

depends on your expertise and tools an expert can do it in 1 and a half hour +-

Posted on Feb 03, 2011

pchambley
  • 334 Answers

SOURCE: i have replaced the water

Unfortunatly its probably the front cover..The waterpump bolts go through it..Pretty big job ..You have to remove the waterpump and loseen the oil pan bolts to get it off.. if its the 3.0 engine

Posted on Sep 17, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace a water pump on a 2004 ford taurus


Wanda, Check out the video and links I posted to see how to remove and replace Taurus water pump.
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
How to Install Water Pump Ford 3 0L V6 FWD WP 9038 AW4094
Ford Taurus Water pump Replacement
Need step by step water pump change
2004 Ford Taurus water pump Google Search

May 31, 2016 | 2004 Ford Taurus

1 Answer

All the water blowing out of the recovering tank in 2002 ford taurus


Could be 2 things,bad thermostat or bad water pump,here's a link on your thermostat,how to replace. GET 35 GIFT CARD FOR EVERY 100 SPENT ON ONLINE SHIP TO HOME ORDERS Here's a link on your water pump,how to replace. GET 35 GIFT CARD FOR EVERY 100 SPENT ON ONLINE SHIP TO HOME ORDERS

May 22, 2015 | 2002 Ford Taurus

1 Answer

Trouble shoot water pump


i would of thought you can just replace the hose.

Feb 27, 2012 | 2002 Ford Taurus

1 Answer

I have a 2002 ford taurus and antifreeze is leaking cant tell from where but it is getting all over my belt and causing smoke could this be a simple hose or a water pump im at a loss


Hello! It sounds like the water pump is leaking...But first, inspect your hoses and their clamping points...
if you can observe coolant leaking, running from the center of the rear of the water pump then it's time to replace it see diagram below for bolt torquing sequence...Bolts1-7=18 Ft. Lbs....Bolts 8-12= 89 In. Lbs.

Guru...........Saailer



9_25_2011_12_27_31_am.gifACDELCO Part # 252467

COST $50; RockAuto.com

Sep 25, 2011 | 2002 Ford Taurus

1 Answer

I have replaced the water pump on my 2002 for taurus and it is still running water some where


Unfortunatly its probably the front cover..The waterpump bolts go through it..Pretty big job ..You have to remove the waterpump and loseen the oil pan bolts to get it off.. if its the 3.0 engine

Sep 17, 2011 | 2002 Ford Taurus

1 Answer

2002 ford taurus. jerks terribly when accelerating from 40 to 60mpg. Mechanic just told us we had a cracked water pump. Can a faulty water pump cause the car to **** when accelerating?


This sounds more like a misfire problem then a waterpump issue. If the waterpump is faulty it should be replaced before any serious overheating issues occur and damage the engine. As far as the waterpump causing the car to **** would say not likely. Is the check engine light on? If so the codes the vehicle has stored would be a better way to get to the issue. Please feel free to ask any additional questions.

Apr 12, 2011 | 2002 Ford Taurus

2 Answers

How many hours will it take to replace a water pump on a 2002 ford Taurus


shop value is around 4 hours but can be done in 3 hours or less

Feb 03, 2011 | 2002 Ford Taurus

1 Answer

2002 ford taurus wtaer pump


Removal & Installation 3.0L (2V) To Remove:
  1. Drain the engine cooling system.
  2. Loosen the water pump pulley.
  3. Remove the bolt and the nut and position the roll restrictor bracket out of the way.
  4. Remove the accessory drive belt.
  5. Remove the generator.
  6. Remove the bolt and the accessory drive belt tensioner.
  7. Remove the nut, the bolt and the support bracket.
  8. Remove the bolts and the water pump pulley.
  9. Disconnect the water pump inlet hose and the crankshaft position sensor electrical connector.
  10. Remove the bolts and the water pump, and clean the sealing surfaces
To Install:
  1. Install the water pump. Tighten bolts in the sequence shown:
    1. Tighten numbers 1-7 to 18 ft.-lbs. (25 Nm)
    2. Tighten numbers 8-12 to 89 in.-lbs. (10 Nm)
    3. Connect the crankshaft position sensor electrical connector and the water pump inlet hose
    4. Install the support bracket.
    5. Install the accessory drive shaft tensioner.
    6. Install the generator.
    7. Install the roll restrictor bracket, bolt and the nut.
    8. Install the water pump pulley.
    9. Install the accessory drive belt.
    10. Connect the battery ground cable.
    11. Fill the engine cooling system.

9de9feb.gif
Water pump bolt torque sequence (3.0L (2V) engine)

Jul 04, 2009 | 2002 Ford Taurus

Not finding what you are looking for?
2002 Ford Taurus Logo

Related Topics:

235 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5522 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...