Question about Cars & Trucks

Open Question

What would cause my 2004 ram 2500 to throw fault codes p0973, p0882, p2769.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 512 Answers

SOURCE: p0973 code

the problem is with the transmission overdrive circuit voltage is low. start by checking the #5 fuse in the fuse block under the hood. if it is ok check for voltages at the trans control relay. past that you may need to take it to a reputible technician for further diagnosis

Posted on Jan 11, 2009

Ad
  • 6 Answers

SOURCE: fault codes for a ram 2500 04

P0191 Fuel Rail Pressure Sensor Circuit Range/Performance

It maybe your Fuel Sensor, or Fuel regulator is bad. Ask dealer if there is a TSB on it, just in case it is a recall on a part that is defective and get a free fix if it is.

"HotRod"

Posted on Oct 24, 2009

  • 33 Answers

SOURCE: Dodge Ram 3500 Diesal 2004 keeps throwing code

contact your dealer service department with the code and they should have no problem hooking you up with the problem

Posted on Dec 29, 2009

Ironfist109
  • 3018 Answers

SOURCE: 2004 Ram 2500 5.9L H.O.

  • This code comes on when the Boost Pressure Sensor indicated less turbo than the ECM set point.

  • Make sure you have check for any blow off hoses etc. Check inter cooler lines etc. I assume you have but you never know.
  • You may want to pull the inter cooler lines and look at the aluminum retainers. The have been known to collapse. This messes the whole seal up and prevents air flow. This is a very common issue. Cummings is the best Diesel out there but this one little snafu has made many a people scratch their head.

  • Hope this helps and thank you for using FixYa


Regards, Tony

Posted on Jul 03, 2011

  • 203 Answers

SOURCE: how do you fix the

this maybe helpful

http://www.obd-codes.com/forums/viewtopic.php?f=1&t=3131

Posted on Jul 18, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I get my 2004 Dodge Ram 3500 5.9 48re out of limp mode?


http://www.cumminsforum.com/forum/911-urgent-situations/909314-p2769-p0973-2007-5-9-w-48re-limp-mode.html#/topics/909314?_k=cp8azv&nocache=1469908570493

this is for the Cummins but sounds like the issue you are having. Not sure why the voltage would go so low as to cause an issue...makes me suspect a failed component inside the tcm (assuming that is where the voltage comes from) causing low voltage to the circuts.

Jul 30, 2016 | Dodge Cars & Trucks

1 Answer

My 2008 dodge ram 2500 is not going into 4wd and is throwing multiple dash lights


Have the OBD codes read as will tell you which sensor/switch is at fault , keep me posted with the OBD codes and i'll try to give further advice etc

Jun 12, 2014 | Cars & Trucks

1 Answer

1998 dodge ram 2500, speedometer does not work


Have the system scanned for fault codes, I think you may have a defective VSS (vehicle speed sensor), but don't replace it before you have the fault code test run, a defective computer and or wiring to the VSS can also cause the same problems.

Jan 23, 2012 | 1998 Dodge Ram 2500 2WD

3 Answers

2004 dodge 2500 with cummins diesal engin light


your code is PCM/ECM power input signal intermittent. this is ussually a sign of a bad connection whether it be in a connector or a short or brake in a wire.

Jan 26, 2010 | 2004 Dodge Ram 2500

1 Answer

2004 Dodge Ram Diesel. Check engine light comes


You will need to have a diagnostic test on this vehicle which will then provide you some error codes.Then once you get the error code you can start looking where the fault is.Hope this helps.

Dec 08, 2009 | 2004 Dodge Ram 2500

1 Answer

Fault codes for a ram 2500 04 p0191 cannot find it does any one know


P0191 Fuel Rail Pressure Sensor Circuit Range/Performance

It maybe your Fuel Sensor, or Fuel regulator is bad. Ask dealer if there is a TSB on it, just in case it is a recall on a part that is defective and get a free fix if it is.

"HotRod"

Oct 24, 2009 | 2004 Dodge Ram 2500

1 Answer

Error code c 00 00


DTC C0000 Vehicle Speed Information Circuit, I hope that helps. Link to 2004 Dodge Ram Service Manual

Sep 25, 2009 | 2004 Dodge Ram 2500

1 Answer

P0973 code


the problem is with the transmission overdrive circuit voltage is low. start by checking the #5 fuse in the fuse block under the hood. if it is ok check for voltages at the trans control relay. past that you may need to take it to a reputible technician for further diagnosis

Jan 11, 2009 | 2005 Dodge Ram 2500 Truck

3 Answers

2004 DODGE RAM 2500 DESIEL


the transfer pump is going bad ...dodge has an intank replacement for your vehicle

Nov 11, 2008 | 2004 Dodge Ram 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...