Question about 2001 Ford Taurus

Open Question

Bleeding coolant system 2000 ford taurus

The pressurized coolant reservoir, thermostat, and any leaking hoses have been replaced.The engine still overheats and the heat blows cold. Water pump and fans are working, the coolant does overflow when the car overheats.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 5 Answers

SOURCE: 1966 Ford Mustang overheating

try to run the water pump without hoses, and add water in the 'in' side, if is powers out the other side, then it's fine. how is your water/coolant mix?

Posted on Dec 01, 2008

Ad
  • 122 Answers

SOURCE: coolant leaking from reservoir cap in a 2000 ford taurus.

no your cap is set to release that pressure by a spring in the cap check the reservoir for the o-ring it could be bad or missing

Posted on Jun 06, 2009

emissionwiz
  • 76118 Answers

SOURCE: overheating engine in 24 valve 96 ford taurus 6 cyl

the thermostat can be easily changed from up top, the T-stat is located at the engine end of the upper radiator hose under the flange the hose connects to. Make sure u follow manufacturer's cooling system bleeding procedures when you refill after the T-stat is changed out.

Posted on Jun 14, 2009

morse008
  • 1111 Answers

SOURCE: 1998 ford expedition 4.6 engine without tow package...overheating

improvise and buy a new hose and 2 clamps and wha-la

Posted on Sep 15, 2009

  • 244 Answers

SOURCE: my 2002 ford taurus has

I have the same vehicle...check to see that the heater control valve is opening...usually mounted on the fire wall and has about a 5/8" inch hose that come from the T-stat....it esentially bypasses the heater core when the heat is not selected. The hoses going through the fire wall on the left (passenger) side of the vehicle are strictly for the heater - it "heat" is selected and those hoses are cold - based on what you've already done, the next conclusion would be the heater control valve...could be something as simple as a disconnected vacuum line.

Good Luck,

Mike...

Posted on Nov 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the thermstat at in a 1998 ford taurus?


I'm guessing you can't find it because it's in a separate housing or located under the lower battery tray in the housing (depending on model of engine). Even though this is specific for 1998; I believe it's the same for 1996-1999 Taurus's. I have access to illustrations, but only .gif and/or .bmp extensions were available which would not copy here. If you need these, I will try an extension change to .jpg. Good luck, this should be enough info. It is helpful to include the engine size in question, for future reference...

Thermostat, Water


c:\users\bob\appdata\local\temp\msohtmlclip1\01\clip_image001.gif CAUTION: Do not mix Standard (green) Coolant with Extended Life Coolant (orange). If mixing occurs, drain engine cooling system and refill with originally equipped coolant type. If this contamination occurs the service change interval on Extended Life Coolant will be reduced from 6 years/150,000 miles to 3 years/30,000 miles.
1.c:\users\bob\appdata\local\temp\msohtmlclip1\01\clip_image001.gif WARNING: NEVER REMOVE THE PRESSURE RELIEF CAP UNDER ANY CONDITIONS WHILE THE ENGINE IS OPERATING. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN DAMAGE TO THE COOLING SYSTEM OR ENGINE AND/OR PERSONAL INJURY. TO AVOID HAVING SCALDING HOT COOLANT OR STEAM BLOW OUT OF THE COOLING SYSTEM OR DEGAS BOTTLE, USE EXTREME CARE WHEN REMOVING THE PRESSURE RELIEF CAP FROM A HOT COOLING SYSTEM OR DEGAS BOTTLE. WAIT UNTIL THE ENGINE HAS COOLED, THEN WRAP A THICK CLOTH AROUND THE PRESSURE RELIEF CAP AND TURN IT SLOWLY UNTIL PRESSURE BEGINS TO RELEASE. STEP BACK WHILE THE PRESSURE IS RELEASED FROM THE COOLING SYSTEM. WHEN CERTAIN ALL PRESSURE HAS BEEN RELEASED, PRESS DOWN ON THE PRESSURE CAP (STILL WITH A CLOTH), TURN AND REMOVE PRESSURE RELIEF CAP

THE ABOVE APPLIES TO ALL MODELS

3.0L (2V) Engine

Removal

Drain the engine cooling system so that the engine coolant level is below the water thermostat (8575) as described.
2.Disconnect the upper radiator hose (8260) from the water hose connection (8592) .
3.Remove the three water inlet connection retaining bolts. Remove the water hose connection .
4.Remove the gasket and water thermostat from the water hose connection . Do not reuse gasket.
Installation
1.Install the water thermostat , gasket and water hose connection as illustrated.
2.Install and alternately tighten the retaining bolts. Tighten bolts to 10-14 Nm (89-124 lb-in).
3.Connect the upper radiator hose to the water hose connection .
4.Fill the engine cooling system with a 50/50 mixture of Premium Engine Coolant E2FZ-19549-AA (green), (in Oregon, F5FZ-19549-CC, in Canada, Motorcraft CXC-10), or Ford Extended Life Engine Coolant F6AZ-19544-AA (orange), or DEX-COOL coolant, or a coolant meeting Ford specification WSS-M97B44-D and water, as described under Cooling System, Draining, Filling and Bleeding procedure.
5.Start the engine and check all hoses and connections for leaks. Allow the engine to warm up so that the water thermostat opens.
6.Stop the engine. Top off degas bottle as required to maintain minimum cold fill level.
c:\users\bob\appdata\local\temp\msohtmlclip1\01\clip_image002.gif
3.0L (4V) Engine
Removal

Drain the engine cooling system so that the engine coolant level is below the water thermostat ; refer to Cooling System Draining, Filling and Bleeding in this section.
2.Raise vehicle on hoist.
3.Disconnect the lower radiator hose (8286) from the water inlet connection.
4.Remove the two water inlet connection retaining bolts. Remove the water inlet connection.
5.Remove the O-ring seal and water thermostat from the water thermostat housing. Inspect O-ring for damage and replace if necessary.
6.If required, remove water thermostat housing retaining bolts, water thermostat housing and O-ring from lower radiator hose tube. Inspect O-ring for damage and replace if necessary.

Installation
1.Install the water thermostat , O-ring, water thermostat housing (if removed) as shown.
2.Install and alternately tighten the retaining bolts. Tighten bolts to 8-12 Nm (71-106 lb-in).
3.Connect the lower radiator hose to the water inlet connection.
4.Lower vehicle.
5.Fill the engine cooling system with a 50/50 mixture of Premium Engine Coolant E2FZ-19549-AA (green), (in Oregon, F5FZ-19549-CC, in Canada, Motorcraft CXC-10), or Ford Extended Life Engine Coolant F6AZ-19544-AA (orange), or DEX-COOL coolant, or a coolant meeting Ford specification WSS-M97B44-D and water; refer to Cooling System, Draining, Filling and Bleeding in this section.
6.Start the engine and check all hoses and connections for leaks. Allow the engine to warm up so that the water thermostat opens.
7.Stop the engine. Top off degas bottle as required to maintain minimum cold fill level.
c:\users\bob\appdata\local\temp\msohtmlclip1\01\clip_image003.gif
3.4L SHO
Removal
Drain the engine cooling system so that the engine coolant level is below the water thermostat ; refer to Cooling System, Draining, Filling and Bleeding in this section.
2.Remove battery.
3.Remove power distribution box.
4.Remove battery tray.
5.Disconnect upper radiator hose and position out of the way.
6.Disconnect the lower radiator hose from the water inlet connection (8K528) .
7.Remove the two retaining bolts. Remove the water inlet connection .
8.Remove the O-ring seal and water thermostat from the water pump (8501) . Inspect O-ring for damage and replace if necessary.

Thermostat

Installation
1.Install the water thermostat , O-rings and water inlet connection as illustrated.
2.Install and alternately tighten the retaining bolts. Tighten bolts to 8-12 Nm (71-106 lb-in).
3.Connect the lower radiator hose to the water inlet connection .
4.Install upper radiator hose . Position spring clamp securely.
5.Install battery tray.
6.Install power distribution box.
7.Install battery.
8.Fill the engine cooling system with a 50/50 mixture of Premium Engine Coolant E2FZ-19549-AA (green), (in Oregon, F5FZ-19549-CC, in Canada, Motorcraft CXC-10), or Ford Extended Life Engine Coolant F6AZ-19544-AA (orange), or DEX-COOL coolant, or a coolant meeting Ford specification WSS-M97B44-D and water; refer to Cooling System, Draining, Filling and Bleeding in this section.
9.Start the engine and check all hoses and connections for leaks. Allow the engine to warm up so that the water thermostat opens.
10.Stop the engine. Top off degas bottle as required to maintain minimum cold fill level.


ad52e081-499a-4e51-a3ef-9bc69a1f9941.gif


5a54c428-0afd-4a37-96ed-ce2033822e88.gif


3f8c57db-bea6-4205-94d5-9a1eb24706fa.gif

Sep 01, 2014 | 1998 Ford Taurus

1 Answer

How do i fix an air lock in cooling system in 2002 ford taurus ses?


There should be air bleeders near the thermostat,and another one else where on the engine at a high point,Break one bleeder loose,(thermostat location) first,with engine off,and pour coolant into the reservoir ,and when the bleeder runs pure water no air bubbles out,then shut the bleeder off.then do the same with the other bleeder.Sometimes allowing the engine to run,until normal engine temp,or a little warmer,and turning the engine off,will allow the cooling system to bleed itself,by waiting about 30 minutes and checking the coolant level in the reservoir to make sure the level is dropping,then u will know the system is bleeding itself,just make sure there is enough coolant in the reservoir before doing this.This may have to be done two,or three times.

Apr 16, 2012 | 2002 Ford Taurus

1 Answer

I have a 2000 taurus can you show me how do I change the thermostat on my car


3.0L OHV Engine
zjlimited_1116.jpg

Fig. Exploded view of the water hose connection and the thermostat assembly - 3.0L OHV engines (click over pic for zoom)
  1. Drain the coolant until the level of the coolant is below the level of the thermostat.
  2. Disconnect the upper radiator hose from the water hose connection.
  3. Unfasten the three water inlet connection retaining bolts and remove the water hose connection.
  4. Remove the gasket and thermostat from the water hose connection. Discard the gasket.
To install:
  1. Clean the water inlet connection mating surfaces.
    NOTE The jiggle valve on the thermostat must be in the up position.
  2. Place the thermostat in the water hose connection making sure the thermostat jiggle valve is facing up.
  3. Install the new gasket and place the water hose connection assembly into position.
  4. Install the water hose connection assembly retainers and tighten them to 89-124 inch lbs. (10-14 Nm).
  5. Connect the upper radiator hose to the water hose connection.
  6. Fill the engine with coolant, start the engine and check for leaks.
  7. Stop the engine and top off the coolant recovery reservoir as necessary.

3.0L DOHC Engine
zjlimited_1117.jpg

Fig. Exploded view of the water inlet connection and the thermostat assembly-3.0L DOHC engines (click over pic for zoom)
  1. Drain the coolant until the level of the coolant is below the level of the thermostat.
  2. Raise the vehicle and support it with jackstands.
  3. Disconnect the lower radiator hose from the water inlet connection.
  4. Unfasten the two water inlet connection retaining bolts and remove the water inlet connection.
  5. Remove the O-ring seal and thermostat from the water inlet connection. Inspect the O-ring for damage and replace as necessary.
To install:
  1. Clean the water inlet connection mating surfaces.
  2. Install the O-ring, thermostat and the water inlet connection. Refer to the accompanying illustration If you can-t remember how the O-ring and thermostat are positioned.
  3. Install the water inlet connection assembly retainers and tighten them to 71-106 inch lbs. (8-12 Nm).
  4. Connect the lower radiator hose to the water inlet connection.
  5. Fill the engine with coolant, start the engine and check for leaks.
  6. Stop the engine and top off the coolant recovery reservoir as necessary.

Good luck (remember to rate this answer).

Apr 27, 2011 | 2000 Ford Taurus

1 Answer

2002 ford taurus. Radiator overflows but, temp gauge not hot.


It could be both your thermostat and water pump, it could also be an air lock in your cooling system. One way or another, I think pressure is building up in part of the system because its not circulating properly.

When its cool, take the top off your reservoir, give the bottom hose to your radiator a good few squeezes, see if the water goes down a little, if it does, you moved something on and probably cured it.

If not, run the engine up, to get it warm and bleed off any air in the system. (Assuming there are bleed taps in the system)

If that also does nothing, I reckon its your water pump. And if your changing that, I'd suggest changing the thermostat at the same time.

Jul 19, 2010 | 2002 Ford Taurus

2 Answers

2000 Ford Taurus Antifreeze boiling over


hi, the problem you are having is down to one of a couple of problems, now as you state the air blows cold then this points towards the thermostat not opening so this then dont pump the coolant round the engine resulting in the top half of the being hot and the bottom half cold so this is why you only get cold air.

so the first thing you should do is get the thermostat changed.

you also need to bare in mind that the problem could be a damaged water pump this does happen from time to time so check for any signs of water leak where the water pump is by the timing belt, if their is no signs of leak then the thermostat is the likely cause.

you also need to think that as the engine has over heated this could have caused the head gasket to fail so this will need looking at to if after changing the thermostat you have the same over heating problem.

so replace the thermostat as this has clearly gone and then when you re-fill the coolant make sure any bleed screws are undone if you have any on your coolant system usually located in one of the top hoses running around the engine, (not all coolant systems have one as many are self bleeding so dont worry if you dont see any bleed screws) now when you start filling the coolant up make sure you only trickle the coolant in to prevent any air lock building up in the system.

if you are unsure what you are doing then please leave this to someone who has some idea of the kind of work involved in this type of repair

Jul 19, 2010 | 2000 Ford Taurus

1 Answer

Coolant won't stay in reservoir.


a good mechanic would have replaced the thermostat when he did the water pump.
May not even have been the water pump in the first place.
Car may have a vapour lock under the thermostat from leting the coolant out when replacing the water pump , and not filling and bleeding the system correctly.
Thermostat won't open if no hot coolant can get to it.

May 07, 2009 | 2000 Ford Taurus

2 Answers

Overheating,reserve coolant tank boiling I have a 2000 Ford Taurus with the similar problem. I had my water pump replaced then this started.


Ford 2000 Taurus

To solve the problem you have the things to do in this order;

) When the engine is cold top off the radiator with fluid. (When the pump was replaced the fluid should have been also)
) Make sure the radiator fluid has anti-freeze in it. This is also anti boil also !
) Add fluid to the overflow reservoir.
) Make sure the drive belt was replaced on the water pump.
) With the engine running, you can add fluid to the radiator for the first minute or so. You want to get air pockets out.
) Replace radiator cap.
) Let car warm up. When it's hot you should get the radiator fan coming on.
) When it get hotter the air-conditioning fan may come on.
) If the fan does not come on, the heat sensor is probably bad.
) If all fans come on, and it overheats, you may have a bad thermostat. Trace the upper radiator hose to where it connects to the engine. That's where it located.

Do not operate the engine when it overheats, You will damage the head gaskets and cause radiator fluid to leak into the cylinders.
If you smell radiator fluid in the exhaust fumes, it may already be leaking.

May 07, 2009 | 2000 Ford Taurus

1 Answer

I need to know what the part is called and how to fix it. The part is leaking hot coolant fluid, it is a ''y'' shape tubing that feels like hard plastic, black in color. It runs on the left side to the...


sounds like hoses going to heater core but they are rubber usually. But it could be the hoses for the degs bottle mounted on the passenger side inner fender.

Coolant Recovery System NOTE: When the water thermostat (8575) is closed, coolant flows through the degas tube and hose assembly from the lower intake manifold to the radiator coolant recovery reservoir (8A080) .

Trapped air in the cooling system must be removed. A pressurized radiant coolant recovery reservoir system is used which continuously separates the air from the cooling system.
  • When the water thermostat is open, coolant flows through both the small hose from the top of the radiator outlet tank and the degas tube and hose assembly from the engine to the radiator coolant recovery reservoir.
  • The radiator coolant recovery reservoir separates any trapped air from the coolant and replenishes the system through its radiator coolant recovery hose.
  • The radiator coolant recovery reservoir serves as the location for:
    • service fill.
    • coolant expansion during warm-up.
    • system pressurization from the pressure relief cap.
    • air separation during operation.
  • The radiator coolant recovery reservoir is designed to have approximately 0.5-1 liter (0.53-1.06 quarts) of air when cold to allow for coolant expansion

Apr 08, 2009 | 1995 Ford Taurus

1 Answer

Need to replace thermostat 2000 taurus


If it's the 3.0L Vulcan Engine (OHV), the thermostat is on the driver's side of the vehicle. Follow the upper radiator hose back to a metal area with three 10mm bolts. This is the thermostat housing. Undo the bolts, and there's the thermostat. Mark the back of it with the old thermostat in it (if you get one with a jiggle valve, it'll make it easier to put the new one in because the jiggle valve needs to be on top). The thermostat and housing aren't perfectly round, so you'll have to play with it a little to get it to line up. Make sure to change the gasket. The spring side of the thermostat goes into the engine.

The water pump is in the serpentine assembly. It's the larger pulley located toward the firewall. It'll be easiest to remove the water pump if you also remove the coolant recovery tank. The water pump pulley has four 1/2" bolts that you need to take out WITH THE BELT STILL ATTACHED. I can't stress this enough. The belt will keep the pulley in place so that you can remove the bolts. Take the pulley off, then the belt. Remove the heater hose at the top and the radiator hose at the bottom. There are 12 bolts of two diameters (1/2" and 10mm if I'm not mistaken). Tap the heater hose lightly with a soft-faced mallet to break the seal with the gasket. Trash the old gasket. Replace gasket (you can also line the mating surface of the water pump with RTV Sealant, put the new gasket on the new pump, and line the other side of gasket with a second coat of RTV sealant if you want a really good seal). Install the water pump and torque to manufacturer's specs. Attach the pulley to the water pump hand tight and put the belt back on. Tighten the pulley bolts. Put the coolant recovery tank back in place. Fill with coolant, start engine, bleed and check for leaks.

To bleed cooling system: Idle the engine until the thermostat opens (you'll be able to tell bacause the upper radiator hose will be uber hot and you'll feel coolant running through this hose). Squeeze all hoses in the system that you can reach, but don't burn yourself. Stop the engine and let it cool. Open the radiator cap and squeeze the COLD upper radiator hose. You'll see some bubbles in your recovery tank. You might have to monitor your coolant level for a couple of days while the final bits of air are purged through your radiator cap (that's why it's pressurized).

Hope this helps. It's not hard, but it took me quite awhile.

Mar 28, 2009 | 2000 Ford Taurus

Not finding what you are looking for?
2001 Ford Taurus Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...