Question about 1995 Eagle Vision

1 Answer

Blower Motor location?

My blower motor has stopped working, and i want to replace it myself. However I can not find where the blower motor is located. Can anyone assist me?

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 146 Answers

The blower motor is behind your glove box. Open the glove box, you will see 2 little rubber tabs on each side that hold it. Push them toward each other and drop the glove box cover down. You should be able to get to everything then. Hope this helps. PHil

Posted on Jan 16, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My heater blowers dnt work and i need to knw where i can locate the resister blocks for my heater blowers so i can ghange them

Its located under dash,or near glove box.

The dash panel lower side has to be out.


Its faulty blower motor resistor. The low and medium speed on blower motor is controlled by resistor and its actual speed is high. So because resistor is not working, blower motors actual speed which is high is working.

It can be faulty blower motor or faulty blower motor resistor. Get the blower motor inspected. If it's faulty it has to be replaced.


For blower motor testing and replacing, check the link below: ----

Blower motor Testing/replacing for all vehicles?


These will help.


Nov 28, 2012 | Cars & Trucks

1 Answer

I have a 1997 Pontiac Grand Prix. I have replaced the blower motor, but that did not correct the problem of no air coming out. So I purchased the resistor, but can not locate it in the dash! I was told...

The Blower Motor Resistor Block is usually located in the air duct on the output side of the blower motor. It is placed here so that air flow from the fan helps stop the resistiors from overheating and burning out. It should be obvious once you look near to where you replaced the blower motor.

Sep 28, 2010 | Pontiac Grand Prix Cars & Trucks

1 Answer

Heater control for fan blower not working. stopped working for about a day then started working again for a day then stopped altogether dead since.

check the blower motor relay, located under the hood fuse/relay box. turn the system on and tap the blower motor see it works. The blower motor located under the glove box.

Apr 19, 2010 | 1992 Honda Civic

1 Answer

Hi i have a94 deville and the blower stopped working and a funny smell (like something is burning in dash)What could cause this?

It may be blower motor failure,I would suggest you replace the blower motor and also replace the blower resistor.The motor is located under the passenger side of the dash,Remove the plastic cover to access it.The resistor is located on the same side also.

Feb 03, 2010 | 1994 Cadillac DeVille

1 Answer

The blower in my 1999 ford taurus stopped working. It does not work at any speed. How do I replace this part myself?

The blower motor isnt hard to replace. A couple of quick questions though, did you check the fuses and relays? Secondly, sometimes the motor can develop a bad ground, did you check that? The blower motor is located under the hood, on the passenger side, on the firewall. It's kind of round looking, and has an electrical connector plugged into it. Turn on the key, put the fan speed selector on high, and jiggle the wiring connector on the blower motor. If nothing, unplug it, and look at the prongs inside the connector. If they look corroded or rusty, try to clean them up with a small wire brush. Otherwise, to remove the motor, simply remove the small bolts that hold the motor in place, there may be 5 of them. Take it out, and replace it with the new one.

Jun 09, 2009 | 1999 Ford Taurus

3 Answers

Lincoln 2000 town car Blower doesn't work at HI-MED-LOW speeds...

it is called blower motor resistor , should be close to blower motor , you will see a plug type connector with two screws , remove the screws and there should be a resistor inside the cover for the motor, swap with new and reassemble

Feb 19, 2009 | 2000 Lincoln Town Car

1 Answer

Blower motor works on high speed only

replaced blower motor resister, located under glove box close to blower motor with black connector.

Jan 16, 2009 | 2002 Mercury Sable

2 Answers

Blower motor installation and location

location is right side under dash , procedure is remove right sound insulator , disconnect blower motor connectors , remove blower motor cooling tube , remove the blower motor screws and blower motor , and reverse procedure to install .thanks.

Dec 28, 2008 | 1998 Chevrolet Cavalier

Not finding what you are looking for?
1995 Eagle Vision Logo

Related Topics:

189 people viewed this question

Ask a Question

Usually answered in minutes!

Top Eagle Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Stewart Dibbs

Level 2 Expert

355 Answers

Are you an Eagle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides