Do I need to buy a vent kit? is this necessary? I bought a battery from walmart do you think it will work well in the bmw? do I need to reset anything?
SOURCE: 2000 BMW 328i yellow oil light on but oil is fine
Your sensor is going bad or you have to change your oil.
SOURCE: HOW DO YOU CHANGE THE BATTERY ON THE REMOTE KEY
Hi , unless you car has been fitted with keyless entry you can not replace the batteries on the romote key , it sounds like the only sollution is to reolace the romote , regards mark
SOURCE: BMW 328i Starter how to replaice
1999 BMW 328I 2.8L EFI DOHC 6cyl
Starter - Removal & Installation
The
starter motor on some models is very difficult to see from the top of
engine compartment as it is covered by the intake manifold. On these
models, without removing the intake manifold, the starter motor must be
removed from underneath the vehicle. Because the starter motor mounting
bolts are not easy to access, a long extension with a universal joint
mounted on a proper sized socket could be used. A three foot
transmission extension is commercially available from tool vendors that
has a 3
/
8
inch drive of the driven end and
1
/
2
inch drive on the drive end. If used with a non-binding impact
universal joint and a proper fitting impact socket, the starter motor
fasteners can be removed from underneath the vehicle.
Once the starter motor fasteners are removed, the
starter motor may have to be moved side-to-side several times to loosen
the dowel pin if it has corroded in place.
NOTE
When the battery is disconnected, the radio code, on-board
computer and clock settings will be lost. The radio code should be
obtained before disconnecting the battery or radio. Once the battery
has been reconnected, the radio will not function unless the code is
keyed in.
Starter motor electrical terminal fastener torque specifications for all models:
M5 terminal fasteners: 44 inch lbs. (5 Nm)
M6 terminal fasteners: 53 inch lbs. (6 Nm)
M8 terminal fasteners: 115 inch lbs. (13 Nm)
Starter motor mounting fasteners:
Hex head bolts: 36 ft. lbs. (49 Nm)
Torx bolts: 32 ft. lbs. (43 Nm)
Starter motor electrical terminal fastener torque specifications for all models:
M5 terminal fasteners: 44 inch lbs. (5 Nm)
M6 terminal fasteners: 53 inch lbs. (6 Nm)
M8 terminal fasteners: 115 inch lbs. (13 Nm)
Starter motor mounting fasteners:
Hex head bolts: 36 ft. lbs. (49 Nm)
Torx bolts: 32 ft. lbs. (43 Nm)
E36 6-Cylinder Engines
Automatic Transmission Models
Manual Transmission Models
Fig. A view of the starter motor mounting fasteners and dowel pin. The mounting bolts are threaded into the starter motor
Fig. The starter motor mounting bolts are a different size than the transmission-to-engine mounting bolts
I hope help you with this (rated this help) Good luck.
SOURCE: my rear plastic window in my 97 328i convertible is cracked
http://www.bmw-convertible-window.com/E36Window.asp
only $129.00
SOURCE: How do you reset the motor and anything else?I
Happens alot. If you or someone pulls the interesting red strap under the rear seat, you have to do a reset. You have a small shot at just re-engaging the motors but will probably have to do a full reset. Take the back seat out and push lever back into the correct position. If you have a semi auto top (have to manually unlock top where it meets the windshield), lift the top back until you can pull up the back of the top to access tonnau cover. If it is a fully auto top, you have to pull out the cover at the very front of the headliner to access manual crank port. There should be a small allen wrench in the trunk tool box. You have to crank and crank and crank until the top is slightly open. You can then lift the back of the top to access tonneau cover. Both top types are the same from here on. Lift up on the tonneau cover and stow the top. Have a friend (or a heavy tool box) push down on the front part of the cover on the passenger side. You will hear a click. This will allow you to open the trunk. There are two motors located in the driver side rear quarter panel. You have to take out the covers hiding them. One motor is sort of in a horizontal placement under the pan where the top is stowed. Push up on this to re-engage. Other motor is in a vertivle orientation and at the driver side rear quater panel. You have to sort of grab the motor with both hands and pull it back into engangement with a gripping motion. Close the trunk. Push the switch to close the top (forward) and hold it down. Insert the key and turn it two clicks (accessory). After about 10 - 15 seconds you will hear the tonneau cover close and then open and the top closes. Let it cycle through and you are done. Hope that helps!
975 views
Usually answered in minutes!
×