Question about Cars & Trucks

1 Answer

04 f350 when the truck sits over night the clutch pedal goes all the way to the floor with no presure you can pump it a few times and it works after it sits again back on the floor?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 75,822 Answers

You have a leak in the hydraulic clutch system, most likely it is the slave cylinder down on the bell housing that is the problem as it is exposed to the most heat stress and wear and tear. The slave is part of the clutch release bearing and that means the transmission must be removed to replace it.

Posted on Nov 06, 2012

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

justuscc
  • 360 Answers

SOURCE: clutch adjustment

its the clutch master and slave unit..... u can get them in a pair with the line all ready bled

Posted on Oct 29, 2008

  • 2 Answers

SOURCE: clutch pedal went to the floor but did not come

there is a plastic clip that connects the clutch pedal to the rod that goes to the master cylinder, chances are that it let go. Bad thing is that it is only available from GM along with the rod. It is around 50

Posted on Oct 24, 2009

  • 133 Answers

SOURCE: 1992 Chevy Silverado - Clutch Slave Cylinder broke

JB weld will not work get it welded by a pro with the proper hi frequency welder otherwise you will have to replace the box ,and yes get a new cylinder ,hope you get sorted

Posted on Mar 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Clutch f350 6.0


Duplicate question.

Nov 06, 2012 | 1989 Ford F 350

1 Answer

Clutch pedal has no pressure and goes straight to the floor when pressed. clutch disk is in good condition. parked the car the night before was working perfect. next morning no pressure and out of fluid....


Pump the clutch pedal and then check for leaks again, including under the dash where the rod from the pedal goes into the clutch master cylinder. Once you find the leak, replace what's leaking and bleed the system to restore the pressure (bleeds from the slave unit, just like bleeding brakes)

May 30, 2011 | 1996 Honda Civic

1 Answer

Clutch sticking will not go into first


Ok it looks like there is no problem with the clutch or tranmission. You problem is that the clutch pedal is stiff and sticking to the floor. This sometimes happens when vehicles sit for extended periods of time. It might free up by working back and forth by hand. Have the vehicle off and the parking brake applied and push the clutch pedal up and down with your hand, It might stick to the floor and you may have to pull it off the floor a few times. You can also get some spray lubricant from your local canadian tire or auto parts store. open the hood and have someone move the clutch pedal up and down and spray the moving parts. It might take a few times to free up the stiff linkage but it will work :)

Mar 07, 2011 | Nissan Se R Cars & Trucks

1 Answer

If i dont pump the clutch a few times it is very hard to shift and the pedal goes clear to the floor until i pump it a couple of times


It is likely you have drawn air into the system. Check the clutch reservoir and refill if needed. Use DOT 3 or 4 brake fluid. Bleed the system to restore clutch pedal. Check the clutch slave cylinder for leaks. If leaking, the slave cylinder will need to be replaced and the system bled again. Please let me know if you have questions.

Dec 18, 2010 | 2000 Kia Sportage

1 Answer

Clutch pedal loses pressure while depressing, slave had leak-- replaced, bleed system-- pedal will occassionally lose pressure and press against the floor until released-- any suggestions?


Either your master cylinder is going ( I had the same problem on my F350 truck) or there is still a small amount of air in the system. As long as the air bubble are dispersed like when the pedal is pumped, it will most likely work. The solution is to properly bleed the system. The easiest is to borrow a vacum pump and **** a few oz of fluid through the bleed screw. The second best requires two people. Have someone sit in the drivers seat and as you open the screw have them press the pedal to the floor holding it there till you retighten the screw. Do this 10 or twelve times making sure you always have fluid in the resevoir. This will push all air out of the system.

Nov 21, 2010 | 1995 Mazda MX-6

2 Answers

My clutch pedal is stuck to the floor??


It is most likely a hydraulic clutch, and it is most likely leaking at the clutch slave cylinder. Check the clutch master cylinder for fluid, it should be a small master cylinder looking thing with a fill cap next to the brake master cylinder and booster unit. If it is empty fill it with the same dot 3 brake fluid that you use for your brake master cylinder, and make sure that you are pouring the fluid into the clutch master cylinder reservoir and not the rubber seal that should be under the fill cap. After filling the clutch master cylinder up with fluid, then try and pump up the clutch pedal. It might take a while to pump up hydraulic pressure, and you might also have to work the pedal a few times by hand at first.

Also, you might have to bleed the clutch at the slave cylinder if it will not build up enough pressure to release the clutch.

Apr 28, 2010 | 1988 Mazda RX-7

2 Answers

The clutch in my 92 Jeep Wrangler suddenly stopped working.


pull the boot back on the master and see if it is wet do the same with the slave

Apr 25, 2009 | 1992 Jeep Wrangler

1 Answer

Clutch worked on day and the next no presure


Do see a leak? Check the fluid level. You likely have a leaking slave cylinder. If the fluid is full, pump the pedal about 50 times, the pedal should get stiff. But check the slave and clutch master for leaks.

Apr 08, 2009 | 1999 Honda CR-V

1 Answer

The clutch on my car stuck to the floor. I check the reservoir was completely empty. I have a feeling the slave cylinder is filled with air. I'll need to get the schematics to see how to bleed the...


lift the pedal manuelly up fill the reservoir on the trasmission on the side near radiator the cylinder there. there a bleader on it open it the oil will come out by gravety its brake oil dot3 that goes in it keep filling the revervoir after a few minute close the bleeder and go pump the clutch pedal many time try it out pierre

Aug 17, 2008 | 2005 Chevrolet Cavalier

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...