Question about Cars & Trucks

1 Answer

I can't remove the front wheel anti lock sensor on a 2002 hyundai elantra GT

The front wheel anti lock sensor will not come out of the hub assembly after removing the hold down bolt

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 76,164 Answers

You will just need to work at it until it comes out, no magic bullet here.

Posted on Nov 06, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Clicking noise in front end 2001 dodge ram 4x4

the ansew i found is replacing the seal around the joint and from both end removing it and cleaning it out i had rocks in mine from going threw water and mud ita a all day deal but a twenty doller fix axle shaft oil seal is all i had to replace

Posted on Apr 26, 2009

  • 333 Answers

SOURCE: Replacing front wheel hub assembly on 2006

Caliper mount bolts are 74 ft/lbs
Driveshaft axle nut is 177 ft/lbs
Hub and bearing mounting bolts are 133 ft/lbs

Posted on Sep 10, 2009

Testimonial: "The info on the torgue specs was very helpful. I couldn't find it anywhere. Thanks a bunch!"

  • 39 Answers

SOURCE: Front wheel stud replacement for a 2006 Hyundai Sonata GL.

grind a flat spot on the round head of the new stud this should give enough clearance to install it. don't pull the hub this will damage the bearing.

Posted on Oct 24, 2009

  • 171 Answers

SOURCE: how to replace 2002 hyundai elantra hub and bearing

With the car on ground, break loose the drive-axle nut, and the wheel nuts , than jack up the car, support it properly, remove the wheel ,remove the axle-nut.
Remove the brake caliper assembly-- support it properly.
Remove the two bolts that hold the hub bracket to the Macpherson strut assemble, remove the lower arm ball joint and remove the steering tie- rod ball-joint attached to the hub bracket. That's it.Slide off the hub /with the bracket off the drive-shaft.
Follow steps backwards to assemble back.

Posted on Apr 09, 2010

  • 1 Answer

SOURCE: Remove the wheel bearing/hub assembly from the

need detailed pictures of how to change rear wheel bearings on a chevy equinox

Posted on Mar 21, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Diagram of front passenger wheel bearing on 2002 hyundai elantra gt


BETTER GET THE SERVICE MANUAL,IT WILL BE EASIER FOR YOU TO UNDERSTAND THE DIFFERENCE.

Mar 12, 2014 | Hyundai Cars & Trucks

1 Answer

Replacing axel on passenger side of 2000 hyundai elantra please give a step by step


  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Front wheel
    • Spindle nut
    • Wheel speed sensor, if equipped
    • Outer tie rod end
    • Stabilizer bar link
    • Lower ball joint
  3. Press the stub shaft out of the hub.
  4. Pry the inner joint out of the transaxle or intermediate shaft.

To install:

NOTE

Use new circlips, split pins and self-locking nuts for assembly.


  1. Install the inner joint so that the circlip is felt to seat in the retaining groove.
  2. Guide the stub shaft into the hub.
  3. Install or connect the following:
    • Lower ball joint and torque the nut to 43-52 ft. lbs. (58-70 Nm)
    • Stabilizer bar link
    • Outer tie rod end and torque the nut to 17-25 ft. lbs. (23-34 Nm)
    • Wheel speed sensor, if equipped
    • Spindle nut and torque the nut to 144-187 ft. lbs. (195-253 Nm)
    • Front wheel
  4. Check and/or adjust the wheel alignment.

Jun 16, 2011 | 2000 Hyundai Elantra

1 Answer

How to replace 2002 hyundai elantra hub and bearing


With the car on ground, break loose the drive-axle nut, and the wheel nuts , than jack up the car, support it properly, remove the wheel ,remove the axle-nut.
Remove the brake caliper assembly-- support it properly.
Remove the two bolts that hold the hub bracket to the Macpherson strut assemble, remove the lower arm ball joint and remove the steering tie- rod ball-joint attached to the hub bracket. That's it.Slide off the hub /with the bracket off the drive-shaft.
Follow steps backwards to assemble back.

Apr 09, 2010 | Hyundai Motor 2002 Elantra

1 Answer

I have a 2002 Lincoln ls . How do I replace the abs speed sensor? Right front tire?


you have one on the inside of each wheel.
SECTION 206-09A: Anti-Lock Control 2002 Lincoln LS Workshop Manual
REMOVAL AND INSTALLATION Front Wheel Speed Sensor
Material Item Specification RTV Silicone Sealant
FSTZ-19G204-AB (Canada CXC-114A) NAVSTR Sealer
Removal and Installation
  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Position the inner splash shield aside.
    1. Remove the pin-type retainers.
    1. Position the inner splash shield aside.
  1. Disconnect the anti-lock brake sensor electrical connector.
  1. Remove the anti-lock brake sensor harness from the brake hose clips.
  1. Remove the anti-lock brake sensor.
    1. Remove the anti-lock brake sensor clip.
    1. Remove the anti-lock brake sensor.
  1. NOTE: Make sure the anti-lock brake sensor is fully seated before installation of the new clip.
    To install, reverse the removal procedure.
    • Apply a 2.5 mm (0.1 in) bead of silicone sealant to the outside diameter of the anti-lock brake sensor.
-------------------------------------------------------------------------
Rear Wheel Speed Sensor Removal and Installation
  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Disconnect the rear anti-lock brake sensor electrical connector.
  1. Remove the rear anti-lock brake sensor harness from the control arm clips.
  1. NOTE: Clean off dirt and foreign material that may have collected around the rear anti-lock brake sensor before removal.
    Remove the rear anti-lock brake sensor.
    1. Remove the anti-lock brake sensor bolt.
    1. Remove the anti-lock brake sensor.
  1. To install, reverse the removal procedure.

Feb 24, 2010 | 2001 Lincoln LS

1 Answer

Need to know why traction control is off and anti lock light is on low trac light is on.....would also like to know where the sensors and channels are located


wheel speed sensors are in the hubs.

these vehicles have a history of problems with
the front hubs wearing out and causing a bad
reading from the front sensor. sensor comes
with the hub.

Nov 22, 2009 | 2002 Pontiac Bonneville

1 Answer

I have a 2002 hyundai elantra and I need to change the driveaxel seal. Any one know how to change it


u have to remove wheel and lower ball join nut from nukole and nut from drive shaft from midle of hub then remove axel and seal

Nov 10, 2009 | 2001 Hyundai Elantra

1 Answer

2005 elantra need answer on removing rotors


REMOVAL:
Loosen the wheel nuts slightly. Raise the front of the vehicle, and make sure it is securely supported.
Remove the front wheel and tire from front hub.
Remove the split pin, then remove castle nut and washer from the front hub while applying the brake.
Remove the caliper mounting bolts, and hang the caliper assembly to one side. To prevent damage to the caliper assembly or brake hose, use a short piece of wire to hang the caliper from the undercarriage.
Remove the wheel speed sensor from the knuckle.
Disconnect the tie rod end ball joint from the knuckle using the special tool (09568-34000).
Remove the split pin.
Remove the castle nut.
Disconnect the ball joint from knuckle using the special tool (09568-34000).
Remove the lower arm ball joint mounting bolts
Remove the strut lower arm mounting bolts
Remove the hub and the knuckle assembly


INSTALLATION:
Reverse the order of the removal procedure.

May 23, 2009 | 2005 Hyundai Elantra

1 Answer

The power steering of Elantra 2007


ELANTRA(XD) > 2001 > TCS > TRACTION CONTROL SYSTEM
C1611 EMS Time-out failure
C1617 EMS Invalid Engine Speed
ELANTRA(HD) > 2007 > ESC > ABS/ESC > C1611 CAN time-out EMS
a7381fc.jpg Seems you may have a wheel speed sensor (right front) which has come apart and is rubbing up against the 'tone wheel' on the axel shaft.

Apr 05, 2009 | 2001 Hyundai Elantra

3 Answers

Buick rendevousz headaches


I own the 2002 Buick Rendezvous CX and I've encountered the same problems listed here. The ABS / Traction Control Lamp stays on and was throwing a code for the left wheel speed sensor as well as an anti-lock brake code (both in the wheel bearing hub assembly). I replaced the left and right front wheel hub assembly yet this did not eliminate the abs codes. 
Ultimately, I traced this problem to a break in the wire that leads to the left hub assembly. Although the sensor was properly connected, the wire (which is encased in a plastic housing) was broken. This is the wiring which leads from the abs wiring harness under the hood down to the left wheel abs sensor. 
I would suggest that you simply remove the left wheel and inspect the wire that leads to the abs sensor (there is only one wire on each wheel). Mine literally fell apart when I removed the plastic housing around the wire. I spliced the wire together and put it back in the plastic housing. After this, my abs codes disappeared and my anti-lock brakes began working again!
This is a simple fix that many people spend $1000 + on by replacing the hub assembly which does not fix the problem.

Aug 20, 2008 | 2002 Buick Rendezvous

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...