Question about Cars & Trucks

Open Question

Bad fuel pump rear tank 1995 ford f150 4.9 ltr

Can a after market electric fuel pump be installed on fuel line too avoid having to remove tank too install factory brand pump

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 508 Answers

SOURCE: fuel is filling front tank from rear on 89 ford e150

Fords had this problem. I believe they actually had a recall notice about this problem. You have a fuel tank switch on the dash somewhere. This is where your problem is located. The switch has gone bad that switches from front tank to the rear tank. About $40.00 for the part.

Posted on Feb 09, 2009

Ad
  • 1 Answer

SOURCE: 1995 ford f150 fuel pump

truck doesn;t start it mite be the fuel pump or relay switch

Posted on Feb 16, 2009

Molson02536
  • 3854 Answers

SOURCE: 1995 firebird 3.4 fuel pump is inoperative

You can but if you ever lose your prim when parked over night or a few day's you may have a starting problem. The other thing too is that your going to have to run new wire's and keep in mind where you live might give you second thought's if there is snow in your area if your going to run it in the winter. That poor fuel pump is going to be exposted. You should be able to do the fuel pump in under 3 hours buy dropping the tank. Good Luck.

Posted on Apr 06, 2009

junit80
  • 81 Answers

SOURCE: Dual tanks on 1990 Ford F150

It should not cause no problems but instead of removing the tank leave it in the truck take out all the fuel in the tank and jus discontinue use of it. This will save you alot of time and trouble and i also suggest that if anyone besides you drives this vehicle then i would put a locking gas cap on it so it cant be accessed at anytime except by you.

Posted on Jun 23, 2009

  • 25 Answers

SOURCE: my newly installed 1990 ford festiva fuel pump DIES

defective new pump
Mike

Posted on Jul 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove fuel tank on 95 Ford aerostar. It has a vapor leak we must repair a leak in vapor recovery system


Removal and Installation
  1. NOTE: Make sure fuel tank (9002) is properly supported during removal and installation procedures.
    Drain fuel from fuel tank .
  1. Loosen fuel tank filler pipe clamp.
  1. Remove fuel tank heat shield (9A032) from vehicle.
  1. Support fuel tank .
  1. Remove bolt from rear fuel tank support strap (9092) and remove rear fuel tank support strap .
  1. Remove bolt from front fuel tank support strap and remove front fuel tank support strap .
  1. Partially lower fuel tank to gain access and remove feed and return lines from sender ports. To disconnect push connect fittings, refer to Push Connect Fittings in this section.
  1. Remove electrical connector from sender unit.
  1. Remove fuel vapor hose from evaporative emission valve (9B593) .
  1. Lower fuel tank from vehicle.

Apr 04, 2017 | 1995 Ford Aerostar

1 Answer

Where is the fuel pump of a ford explorer sport trac pick up located


zjlimited_701.gif

Fig. Fuel pump flange bolt torque sequence-2002 Explorer and Mountaineer and Sport-Trac Sport Built Before 03/2002

  1. Before servicing the vehicle, please familiarize yourself with safety procedures.
  2. Disconnect the battery ground cable.
  3. Relieve the fuel system pressure.
  4. Drain the fuel tank.
  5. 4WD vehicle
    1. Remove the fuel tank skid plate bolts.
    2. Remove the fuel tank skid plate rear left bolt.
    3. Remove the fuel tank skid plate rear right bolt and lower the fuel tank skid plate.
  6. All vehicles
    1. Use a suitable jack to support the fuel tank.
    2. Remove the vent hose.
    3. Remove the bolt and reposition the fuel tank support strap.
    4. Remove the support bolts and push the fuel tank back until the lip clears the support bracket.
    5. Lower the fuel tank just enough to expose the fuel lines and the fuel tank transducer connector.
    6. Disconnect the fuel line and the vapor line.
    7. Disconnect the fuel tank electrical supply connector near the frame rail. Lower the fuel tank.
  7. Clean the area around the fuel pump assembly mounting flange.
  8. Disconnect the electrical connector from the fuel pressure transducer.
    WARNING The fuel pump assembly must be handled carefully to avoid damage to the float arm and the filter.
  9. Remove the fuel pump mounting bolts and remove the fuel pump assembly.

Hope helps.

Sep 11, 2011 | Ford Explorer Sport Trac Cars & Trucks

1 Answer

Access panel for fuel pump


There is none:

Fuel Tank & Fuel Pump Module Assembly Removal & Installation To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Shift the vehicle into NEUTRAL and position it on a hoist.
  3. Release the fuel pressure.
  4. Disconnect the negative battery cable.
  5. Remove the fuel tank filler cap.
  6. Drain as much fuel from the tank as possible.
  7. Using suitable hose pinching pliers, clamp the fuel tank filler hose. Clamp the fuel tank filler hose in the location shown ford-05-00-396.gif

  8. Disconnect the three quick connect couplings from the fuel tank tubes at the tank.
  9. Disconnect the fuel pump electrical connector.
  10. Disconnect the fuel filter inlet tube from the filter.
  11. Position a suitable lifting device under the fuel tank.
  12. Remove the two fuel tank support strap bolts.
  13. Lower the fuel tank to access the fuel pump module while swinging the fuel tank support straps away from the tank.
  14. Clean the area around the fuel pump mounting flange.
  15. Disconnect the fuel pump module electrical connector and the fuel pump module fuel outlet tube.
  16. Using the special tool, turn the fuel pump module retaining ring counterclockwise and remove it. CAUTION
    The fuel pump module must be handled carefully to avoid damage to the float arm, filter and convolute hoses.
  17. Turn the fuel pump module counterclockwise and the fuel pump module will release from the locking tabs. Remove the fuel pump module from the fuel tank.
To Install:
  1. Install the fuel pump module in the fuel tank.
  2. Connect the fuel pump module electrical connector and the fuel pump module fuel outlet tube.
  3. Raise the tank into position and install the mounting strap bolts. Tighten the bolts to 26 ft-lbs (35 Nm).
  4. Connect the fuel lines and electrical connectors at the fuel tank.
  5. Lower the vehicle and refill the tank.
  6. Connect the negative battery cable.
  7. Turn the ignition key to the ON position to pressurize the fuel system.
  8. Visually inspect the fuel system for leaks.
prev.gif next.gif

Oct 05, 2010 | 2000 Ford Taurus

2 Answers

How do you change the fuel pump? is there a access panel and if so where is it located?


Removal & Installation
To Remove:


  1. Before servicing the vehicle, refer to the precautions at the beginning of
    this section.
  2. Release fuel pressure.
  3. Remove or disconnect the following:

    • The rear seat





      Electrical Connector
      dod_intrpd_fuel__tank_elec_conn.gif



    • The fuel pump electrical connector





      Battery Cable
      dod_intrpd_batt_conn.gif



    • Battery cable

  4. Raise and safely support the vehicle
  5. Remove or disconnect the following:





    Fuel Tank Drain
    dod_intrpd_fuel_tank_drain.gif




    • Fuel from fuel tank





      Stabilizer Bar
      dod_intrpd_stab_bar.gif








      Stabilizer Bar and EVAP Canister
      dod_intrpd_evap_cann.gif



    • The rear stabilizer bar brackets from body
    • Stabilizer bar toward rear of vehicle





      Fuel Filler Tube
      dod_intrpd_filler_tube.gif



    • The fuel filler tube from fuel tank





      Fuel And EVAP Lines
      dod_intrpd_fuel_evap_lines.gif



    • Fuel and EVAP lines

  6. Position transmission jack under fuel tank assembly.
  7. Remove fuel tank straps bolts passenger side first.
  8. Lower fuel tank and remove the purge line and vent line.
  9. Disconnect fuel line from fuel pump module by depressing quick connect
    retainers with thumb and fore finger.
  10. Slide fuel pump module electrical connector lock to unlock.
  11. Disconnect the electrical connection from the fuel pump module, by pushing
    down on connector retainer and pulling connector off of module.





    Fuel Tank Locknut
    dod_intrpd_fuel_tank_tool__nut.gif



  12. Use Special Tool # 6856 to remove fuel pump module locknut.
  13. Remove fuel pump and O-ring seal from tank. Discard old seal.

To Install:


  1. Wipe seal area of tank clean and place a new seal in position in the tank
    opening.





    Fuel Tank Locator
    dod_intrpd_fuel_pump_loctr.gif



  2. Position fuel pump in the tank.

    • Make sure the alignment tabs on the underside of the fuel pump module flange
      sits in the notches on the fuel tank.

  3. Position the locknut over the fuel pump module.
  4. Tighten the locknut using Special Tool # 6856

    • Torque to: 40.5 ft. lbs. (55 Nm)

    CAUTION
    Over tightening the pump lock ring may
    result in a leak.

  5. Position the fuel tank on the transmission stand.
  6. Install or connect the following:

    • Fuel pump electrical connector into hole in the body
    • The purge and vent lines
    • Fuel tank and tank straps
    • The fuel filler tube and tighten the clamp
    • The stabilizer bar and install bolts

  7. Lower vehicle.
  8. Install or connect the following:

    • The fuel pump electrical connector that is in the rear seat
    • The rear seat
    • The battery cable

  9. Fill fuel tank.
  10. Use the DRB or equivalent scan tool to pressurize the fuel system.
  11. Check for leaks.


prev.gif next.gif

Sep 23, 2010 | 1999 Chrysler Concorde

2 Answers

How do u get the fuel pump on


Removal & Installation To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Shift the vehicle into NEUTRAL and position it on a hoist.
  3. Release the fuel pressure.
  4. Disconnect the negative battery cable.
  5. Remove the fuel tank filler cap.
  6. Drain as much fuel from the tank as possible.
  7. Using suitable hose pinching pliers, clamp the fuel tank filler hose. Clamp the fuel tank filler hose in the location shown ford-05-00-396.gif

  8. Disconnect the three quick connect couplings from the fuel tank tubes at the tank.
  9. Disconnect the fuel pump electrical connector.
  10. Disconnect the fuel filter inlet tube from the filter.
  11. Position a suitable lifting device under the fuel tank.
  12. Remove the two fuel tank support strap bolts.
  13. Lower the fuel tank to access the fuel pump module while swinging the fuel tank support straps away from the tank.
  14. Clean the area around the fuel pump mounting flange.
  15. Disconnect the fuel pump module electrical connector and the fuel pump module fuel outlet tube.
  16. Using the special tool, turn the fuel pump module retaining ring counterclockwise and remove it. CAUTION
    The fuel pump module must be handled carefully to avoid damage to the float arm, filter and convolute hoses.
  17. Turn the fuel pump module counterclockwise and the fuel pump module will release from the locking tabs. Remove the fuel pump module from the fuel tank.
To Install:
  1. Install the fuel pump module in the fuel tank.
  2. Connect the fuel pump module electrical connector and the fuel pump module fuel outlet tube.
  3. Raise the tank into position and install the mounting strap bolts. Tighten the bolts to 26 ft-lbs (35 Nm).
  4. Connect the fuel lines and electrical connectors at the fuel tank.
  5. Lower the vehicle and refill the tank.
  6. Connect the negative battery cable.
  7. Turn the ignition key to the ON position to pressurize the fuel system.
  8. Visually inspect the fuel system for leaks.
prev.gif next.gif

Aug 19, 2010 | 2001 Ford Taurus

2 Answers

My fuel pump is bad! how do i replace this? this


unhook battery, remove all gas,jack rear of car up and always use safety stands, unhook straps that hold the tank in place,be careful with fuel lines, fuel pump is on the top of tank, there is a locking ring on the pump, remove it and replace.

Jun 17, 2010 | 1998 Ford Taurus

2 Answers

How do i replace fuel pump on 1998 escort se 2.0


Removal & Installation WARNING Extreme caution should be taken when removing the fuel tank from the vehicle! Ensure that all removal procedures are conducted in a well ventilated area! Have a sufficient amount of absorbent material in the vicinity of the work area to quickly contain any fuel spillage. NEVER store waste fuel in an open container, as it presents a serious fire hazard!

This procedure will require a new fuel pump gasket for pump installation, so be sure to have one before starting.
  1. Relieve the fuel system pressure.
  2. Disconnect the negative battery cable.
  3. Remove the rear seat cushion and unplug the electrical connectors from the fuel pump.
  4. Unfasten the four pump access cover screws and remove the cover.
  5. If equipped, unplug the pump electrical connector located under the cover.
  6. Unfasten the fuel line clip(s) and disconnect the line(s) from the pump.
  7. Use a fuel pump locking ring removal tool or a brass drift and a hammer to unfasten the pump locking retaining ring.
  8. Remove the fuel pump and the gasket from the tank.


ac8ef02.gif

To install:
  1. Install a new gasket and place the pump into position in the tank.
  2. Install the pump locking retaining ring.
  3. Connect the fuel line(s) to the pump and install the line retaining clip(s).
  4. If equipped, attach the fuel pump electrical connection(s).
  5. Install access cover, then tighten the retainers.
  6. Attach the pump electrical connector(s).
  7. Install the rear seat cushion.
  8. Connect the negative battery cable.
  9. Start the car and check for proper operation.

May 13, 2010 | 1998 Ford Escort

2 Answers

How to replace my 2001 ford taurus fuel pump Instructions


2001 Ford Taurus V6-3.0L DOHC VIN S
Fuel Pump: Service and Repair

REMOVAL
1. Remove the fuel tank.
2. Clean the area around the fuel pump mounting flange.
3. Using the special tool, remove the fuel module retaining ring.(Screwdriver and hammer)
4. Remove the fuel delivery module from the fuel tank.
CAUTION: The fuel delivery module must be handled carefully to avoid damage to the float arm, filter, and convolute hoses.
INSTALLATION
1. To install, reverse the removal procedure.
NOTE: A stop should be felt when aligning the raised arrow on top of the fuel tank delivery module to the dot on the fuel tank.

Sep 08, 2009 | 2001 Ford Taurus

1 Answer

Starving for gas


check fuel filter first. rate as fixed if this helps.

Steel Midship, Aerostar
Removal and Installation
  1. NOTE: Make sure fuel tank (9002) is properly supported during removal and installation procedures.
    Drain fuel from fuel tank .
  1. Loosen fuel tank filler pipe clamp.
  1. Remove fuel tank heat shield (9A032) from vehicle.
  1. Support fuel tank .
  1. Remove bolt from rear fuel tank support strap (9092) and remove rear fuel tank support strap .
  1. Remove bolt from front fuel tank support strap and remove front fuel tank support strap .
  1. Partially lower fuel tank to gain access and remove feed and return lines from sender ports. To disconnect push connect fittings, refer to Push Connect Fittings in this section.
  1. Remove electrical connector from sender unit.
  1. Remove fuel vapor hose from evaporative emission valve (9B593) .
  1. Lower fuel tank from vehicle.

Apr 28, 2009 | 1995 Ford Aerostar

2 Answers

I am not getting fuel to my engine


Removal
  1. Relieve the Fuel System Pressure . Refer to the procedure in this section.
Cushion Cover and Pad, Rear Seat — One-Piece and 50/50 Split Fold Removal
  1. Remove the two rear seat cushion bolts.
  1. Fold the rear seat back cover and cushion (60084) forward.
  1. Carefully pull the rear seat cushion and cover (60030) out from under the rear seat back cover and cushion and remove the rear seat cushion and cover from the vehicle
  1. Remove the rear seat cushion and cover (60030). Refer to Section 01-10 for the removal procedure.
  1. Remove the three luggage compartment floor cover hold-down pins and fold the luggage compartment floor cover (45455) forward until the fuel pump assembly access plate is visible.
  1. Remove the four fuel pump assembly access plate screws, the ground lead, and the fuel pump assembly access plate from the chassis.




  1. Disconnect the fuel pump assembly electrical connector.




  1. On 4-door vehicles, remove the fuel vapor tube shutoff valve bolt and the evaporative emission tube shut off valve (9G332) from the bracket on the fuel pump assembly housing.




  1. Loosen the two hose clamps and disconnect the two fuel pump hoses from the fuel pump hose fittings on the fuel pump assembly housing.




  1. Remove the four screws (2-door) or eight screws (4-door) and lift the fuel pump assembly housing from the fuel tank (9002).




  1. Disconnect the fuel level sensor electrical connector.
  1. Remove the two fuel level sensor washers and fuel level sensor nuts and the fuel level sensor.



-------------------------------------------------------------------------------------
Section 10-01: Fuel Tank, Filters, Lines and Electric Fuel Pump 1996 Aspire Workshop Manual
REMOVAL AND INSTALLATION Fuel Pump Removal
  1. Remove the fuel level sensor. Refer to the Fuel Level Sensor removal procedure in this section.
  1. Remove the fuel pump screw, fuel pump grommet and the fuel pump bracket from the bottom of the fuel pump (9350).




  1. Remove the fuel tank sender filter bracket, fuel tank sender filter (9A011) and the fuel tank sender filter retainer from the fuel pump.
  1. Disconnect the fuel pump electrical connector.
  1. Remove the clamp and the fuel pump from the fuel pump assembly housing.

Apr 19, 2009 | 1995 Ford Aspire

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...