Question about 1997 Ford Taurus

Open Question

Where are p1131 and p1151 ho2s11 sensors location

Code po161,p1131,po1151 how to fix poblem to shut check engin lite off

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 77194 Answers

SOURCE: P0401. P0133, P1131- emmision test

Based on what the tech manuals say I would change the DPFE sensor for the EGR Valve, careful not to tear the special silicone rubber hoses that go to it from the exhaust, as a Ford dealer tech I saw these codes allot, and the DPFE sensor was almost always the issue or the hoses going to it.

Posted on Oct 16, 2008

Ad
  • 116 Answers

SOURCE: 98 E-250 Rough Idle; codes p0156,p1131,p1151,p0301,p0171,p0174+

po301 thru po306 all misfire codes cylinder 1-6 remove plugs and replace them..... set the plug gap first
i suggest u replace the wires also if they never been replaced all these misfire codes can set the others and one is for the oxygen sensor ( 02s or HO2S) CIRCUT MALFUNCTION do u know how to check wireing systems
do the tune up plugs (set gap) .052-.056 change the fuel filter also. clear the codes hows it run
this info is for 98 E-250 4.2Litre
what engine do u have 4.2L or 4.6L i know it is a v-6 by the codes

Posted on Dec 15, 2008

  • 5 Answers

SOURCE: Where is the fuel pressure regulator located on an 2002 f150 v6?

in the center of the motor,in the rear on the fuel rail

Posted on Jan 19, 2009

saailer
  • 1871 Answers

SOURCE: P0136, P1131, and P1151 codes on Ford Expedition 2000 4.6L

Your auto has four O2 sensors. Two upstream and two downstream; With two banks. Bank 1, sensor 1...and bank 2, sensor 1 are the two upstream (exhaust manifold before the catalytic). Bank 1, sensor 2 and bank 2, sensor 2 (other side of catalytic)

Code 1131= upstream; bank 1..sensor 1
Code 1151= upstream; bank 2..sensor 1
Code P0136 (generic code) bank 1..sensor 2 (questionable)

I wouldn't spend the money to purchase 3 sensors. Highly unlikely all three are bad; Cost is about $40/ ea.
Since there isn't a code for the cat's themselves, I would suspect the O2 circuit is malfunctioning. The rough idle is another clue.


Take an ohmmeter set it on X10 scale and measure the resistance from engine to body and body to negative post on battery terminal. You should read zero ohms (full needle deflection). If you do go buy two upstream O2 sensors. If you read
open or a high resistance run two straps from eng. to body...and body to neg.batt. post.

FixYaWIZ................saailer

Posted on Dec 10, 2009

tneubauer
  • 437 Answers

SOURCE: how do i fix emission codes p1131 p1151 p0171

TSB
05-22-6
ISSUE:
Some 2001-2003 F-150, 2004 F-150 Heritage and 2001-2003 E-150/250 vehicles equipped with a 4.2L engine may exhibit the malfunction indicator lamp (MIL) on with diagnostic trouble codes (DTCs) P1131 and/or P1151 (system too lean bank 1 or 2). This condition may be due to leaking isolator bolts/port gaskets in the upper-to-lower intake manifold mounting area. This condition is sometimes intermittent and may not be apparent on a warmed-up engine.


SERVICE PROCEDURE

Perform a self test. If DTC P1131 and/or P1151 are the only codes stored in the powertrain control module (PCM) proceed to Step 2. If any additional DTCs are present, follow normal diagnostic procedures found in the PC/ED Manual.

Remove the upper intake and replace only the port gaskets (9H486) and isolator bolt assemblies (9S479). The new isolator bolt assemblies use a rubber material that is green in color, do not install the old isolator bolt assemblies with the black rubber material. Do not replace any other intake parts or gaskets.
While the upper intake manifold is removed, check the exhaust gas recirculation (EGR) orifices that are pressed into each primary port of the lower intake manifold. If any of the orifices are plugged with soot, clean and unplug them with a pick and solvent.

PART NUMBER PART NAME
1L3Z-9H486-AA Port Gasket
3F2Z-9S479-AA Isolator Bolt

Posted on Jan 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Chevy Silverado error p1151


P1151 Lack of Upstream Heated Oxygen Sensor Switch - Sensor Indicates Lean - Bank No. 2


p1131 p1151 p0171 p0174 p1131 p1151 p0171 p0174
All of these p1131 p1151 p0171 p0174 codes indicate a problem with a lean condition. This engine is known for vacuum leaks, so before you start throwing oxygen sensors at the problem, it pays to perform some diagnostics.
Start by cleaning the MAF sensor. Spray the sensor with CRC MAF sensor cleaner. Next, check the plastic vacuum lines, especially where they meet with rubber boots. If they are cracked or the rubber is swollen, replace the line. Then check the rubber elbow that holds the PCV valve. That elbow is a know failure point. In fact, the entire PCV tubing is a trouble spot on these engines. (thanks Ford).
After you've checked for vacuum leaks, check the operation of the oxygen sensors. The easiest way to do that is to disconnect the sensor from the harness. Connect one lead of your digital voltmeter to the black wire on the sensor and the other lead to battery negative. Then start the engine and add fuel (either propane, starting fluid, or carb cleaner) into the throttle body to force the mixture to rich. You should see a corresponding increase in voltage as you add fuel (from 0 volts to slightly less than 1 volt). Start and stop the fuel enrichment and watch the meter to see if the volts drop as you stop adding fuel. If you see no change, the sensor is dead. Replace it.
You can also use the fuel enrichment procedure to locate intake gasket leaks.
P1131 Lack of Upstream Heated Oxygen Sensor Switch - Sensor Indicates Lean - Bank No. 1
P1151P1151 Lack of Upstream Heated Oxygen Sensor Switch - Sensor Indicates Lean - Bank No. 2
P0174 system lean bank 2
P0171 system lean bank 1


This is the only info that didn't come back directly to FORD (yet still mentions it) instead of GM. Not to sure you got the correct code.

Jul 08, 2014 | 1999 Chevrolet Silverado 1500

1 Answer

Error code P1131 & P1151


Hope this helps you or future parties of intrest. P1131 Lack of Upstream Heated Oxygen Sensor Switch - Sensor Indicates Lean - Bank No. 1 P1151 Lack of Upstream Heated Oxygen Sensor Switch - Sensor Indicates Lean - Bank No. 2 I would get under your stang and gently clean outside portion of o2 sensors using a scotch brite. Also if you have so dielectric grease pull electrical connections to o2 sensors clean them and add grease. These trick eliminated the o2 sensor OBD1 codes on my 1987 Ford mustang gt

Oct 22, 2013 | Ford Mustang Cars & Trucks

1 Answer

I need to know the meaning of code p1131 on 2001 ford escape


P 1131 Oxygen sensor bank 1 sensor 1 lack of switching, You can have a vauum leak causing this sensor to read lean or the sensor went out and doesnt switch

Mar 01, 2012 | 2001 Ford Escape

2 Answers

2000 Lincoln Navigator - few days ago started idling very rough when truck is at a stop or in park. Service Engine Light came right around time I noticed that it was idling rough when stopped. Following...


P1131 Lack of HO2S-11 Switch ,Sensor Lean
P1151-Lack of HO2S-21 Switch ,Sensor Lean
PO171- System to Lean (Bank 1)
PO174-Systen to Lean (Bank 2)

Fuel Filter -Plugged
Low Fuel Pressure
Evap System -Leaks
Leaks - in ducting,air filter to throttle
PCV -Leaks
Exhaust System -Leaks
O2 Sensors-worn out

Apr 06, 2011 | 2003 Lincoln Navigator

1 Answer

P1131,p1151,p0174


Hello,
P1131 = Lack of HO2S11 switch - sensor indicates lean, ( upstream heated oxygen sensor )
This oxygen sensor is located before the catalytic converter, ( refered to as UPSTREAM )

P1151 = Lack of HO2S21 switch - sensor indicates lean, ( could be up, or downstream heated oxygen sensor ) " Downstream ", meaning after the catalytic converter.

PO174 = System too lean, ( bank 2 ) The fuel/air mix ratio is bad.

These DCT codes are generally caused by a problem with the emissions system. The following items are a few of the most common items to trigger those codes.

1. Dirty air filter. ( very common )
2. Faulty idle air control valve. ( common )
3. MAF, ( mass air flow ), sensor. ( very common )

All 3 of the above can prevent the onboard computer from determining the proper fuel/air mix ratio.
The oxygen sensors measure to insure the fuel/air mix produces maximum power with minimal emissions.

I hope this helps you.
Feel free to contact me in the comment section if you have a question.

Feb 15, 2011 | 2002 Ford F150 Regular Cab

1 Answer

What is the p1131 and the p1151 codes mean?


P1131 and P1151 are for the oxygen sensors. one in the exhaust at the firewall and one at the radiator off the manifold. When both go off though at the same time I would suspect a vacuum leak after the MAF sensor(mass air flow), if only one code then suspect that O2 oxygen sensor

Jan 19, 2011 | 2000 Lincoln Town Car

1 Answer

Idling rough in cold weather codes that come up are p1131 and p1151 need to know what these codes are and what parts they are


DTC P1131 DTC P1151 indicates the system is correcting RICH for an overly LEAN condition. The Heated Oxygen Sensor (HO2S) voltage is less than 0.45 volts. This is usually due to a vacuum leak after the MAF. It can also be caused by a bad PCV valve or PCV system hose. It can also be caused by low fuel pressure or a plugged injector.

Start with the simple and clean the MAF and the IAT sensor. In simple terms, the engine is running lean and is being compensated by the ECM. P1131 is bank 1 and P1151 is bank2

Good luck and keep me posted.




Feb 17, 2010 | 2001 Ford F150 Styleside SuperCrew

2 Answers

2002 Ford Windstar Error Code P1131 And P1151


those two codes are for the o2 sensors. both are the upstream sensors on the front and rear banks. so they are desinagted bank 1 sensor 1 and bank 2 sensor 1. them most common cause for this is faulty o2sensors , bad gas and of a poor running engine. so if your car runs good (no misfire) and gas is ok then replace the o2sensor witch is the very most common cause.

Jan 28, 2010 | 2000 Ford Windstar

2 Answers

How do i fix emission codes p1131 p1151 p0171


TSB
05-22-6
ISSUE:
Some 2001-2003 F-150, 2004 F-150 Heritage and 2001-2003 E-150/250 vehicles equipped with a 4.2L engine may exhibit the malfunction indicator lamp (MIL) on with diagnostic trouble codes (DTCs) P1131 and/or P1151 (system too lean bank 1 or 2). This condition may be due to leaking isolator bolts/port gaskets in the upper-to-lower intake manifold mounting area. This condition is sometimes intermittent and may not be apparent on a warmed-up engine.


SERVICE PROCEDURE

Perform a self test. If DTC P1131 and/or P1151 are the only codes stored in the powertrain control module (PCM) proceed to Step 2. If any additional DTCs are present, follow normal diagnostic procedures found in the PC/ED Manual.

Remove the upper intake and replace only the port gaskets (9H486) and isolator bolt assemblies (9S479). The new isolator bolt assemblies use a rubber material that is green in color, do not install the old isolator bolt assemblies with the black rubber material. Do not replace any other intake parts or gaskets.
While the upper intake manifold is removed, check the exhaust gas recirculation (EGR) orifices that are pressed into each primary port of the lower intake manifold. If any of the orifices are plugged with soot, clean and unplug them with a pick and solvent.

PART NUMBER PART NAME
1L3Z-9H486-AA Port Gasket
3F2Z-9S479-AA Isolator Bolt

Jan 13, 2010 | 2003 Ford F150 Regular Cab

1 Answer

Have engine trouble codes P1151 and P1131


If both, P1131 and P1151 trouble codes are set at the same time, the problem will most likely be attributed to a vacuum leak past the MAF (Mass Air Flow) sensor or something else that would likely affect BOTH banks. If the problem is only causing one code or the other, but NOT both, the problem will most likely be something that would affect one bank, like a bad O-2 sensor or a fuel injector; the most common cause of a single code either the P1131 or P1151 in my experience has been a bad Oxygen sensor.

Nov 07, 2009 | 2001 Mazda Tribute

Not finding what you are looking for?
1997 Ford Taurus Logo

Related Topics:

147 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

fordexpert

Level 3 Expert

5575 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...