Question about 2002 Chevrolet Corvette

1 Answer

Bakup light replacement,how to get to it

How to get to bulb?

Posted by on

  • gwse2003 Jan 05, 2009

    for a 2002 corvette conv

  • gwse2003 Jan 05, 2009

    Thx for info,figured that might be the way



1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 21 Answers

Pull the cover off inside the trunk

Posted on Jan 05, 2009

  • greaseee Jan 05, 2009

    yea man no problem been working on cars sience i was 5 give me a shout if you need anything else



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a 2005 chev impala can i replace my high beams headlights with just low beam lights


Jul 05, 2011 | 2005 Chevrolet Impala


Brake Lights Dull or Flickering - All Cars

Dull or Dim Brake Light Repair: If your car has a dull or dim brake light it is dangerous to you and other drivers. A dim brake light is a mystery to most people because the bulb is working, just not correctly. First confirm a new and correct brake light bulb has been installed. Next, turn the ignition key to the "on" position and have a helper depress the brake pedal. With the bulb installed touch a grounded test light to the outer bulb holder ring. If the bulb brightness changes the bulb socket ground has high resistance and needs to be repaired or replaced.

Flickering Brake Light Bulb Repair: A flickering brake light bulb can be very distracting and annoying. A brake light flickers because the power or ground is being obstructed momentarily. The most common cause for this condition is a loose fitting bulb socket. To check for this condition remove the brake light bulb in question, while a helper hold their foot on the brake pedal move the bulb around slightly in the socket. If the bulb flickers replace or repair the bulb socket as needed to regain proper brake light bulb operation. If the brake light bulb socket tests ok wiggle the brake light fuse and wiring at the brake light bulb socket, brake light switch and turn signal switch (American cars). If the brake light bulb flickers repair the component or wiring as needed.
Preferred Procedure: Always replace brake light bulbs with manufacturers recommend replacement bulbs. If you cannot find the correct replacement bulb part number consult an auto parts store for additional manufacturer information.
Common Problems
When brake light bulbs are replaced with the incorrect bulb causing no or dim brake light operation
If the brake lights stay on continuously it could mean the brake light switch has failed or an adjustment is needed.

on Dec 18, 2009 | Honda Civic Cars & Trucks

1 Answer

How to replace bulb in front bumper turn signal housing 1995 jag xj6

  • Identify the blown bulb. Note that if a headlight bulb has blown, the dip beam is on the outside and the high beam is on the inside. Turn off the ignition switch and light switches.

  • Open the hood and replace any blown headlight bulbs. Press the plastic spring clips and remove the bulb holder from the assembly. Pull the bulb out of the bulb holder and replace it with a new bulb. It only fits one way. Be sure not to touch the bulb's glass. Replace any parking lights at the same time, they are in the headlamp unit too.

  • Remove the front turn signal light unit in the bumper to change the turn signal bulb. Push gently on the inside edge and insert a blade between the bumper and the lens at the outside edge. Compress the spring and remove the lens. Fit a new lamp by inserting it into the plug. The side marker light is changed using a similar process.

  • Open the trunk to replace the rear fog light, stop light, tail light, reversing light and turn signal light. Remove the rear light cover and turn the bulb holder fastener 90 degrees counter clockwise. Remove the expired bulb, fit a new one and replace the parts, turning the bulb holder clockwise.

  • Thanks..

    May 21, 2011 | 1995 Jaguar XJ6

    1 Answer

    My tail light housing were just replaced from an accident and the reverse lights dont work

    i have a 2007 tc, and found that the plugs for the bakup lights were unplugged, check to see if this has happened to you

    Mar 29, 2011 | 2008 Scion Tc

    1 Answer

    I need to fix Dash air vent light -Left side - that goes on and off- How due I remove the bulb and check the wiring?

    Check out the "Instrument Cluster Light Bulbs" section below:

    2002 Volkswagen Passat - Repair Manual - Chassis Electrical (excerpt)

    Dome/Map/Cargo Light

    1. Disconnect the negative battery cable.
    2. Remove the bulb from its retaining clip contacts. If the bulb has tapered ends, gently depress the spring clip/metal contact and disengage the light bulb, then pull it free of the two metal contacts.

    To install:
    1. Before installing the light bulb into the metal contacts, ensure that all electrical conducting surfaces are free of corrosion or dirt.
    2. Insert the bulb into the holder. If the contacts have small holes, be sure that the tapered ends of the bulb are situated in them.
    3. To ensure that the replacement bulb functions properly, activate the applicable switch to illuminate the bulb which was just replaced. If the replacement light bulb does not illuminate, either it is faulty or there is a problem in the bulb circuit or switch. Correct as necessary.
    4. Install the cover until its retaining tabs are properly engaged.
    5. Connect the negative battery cable.

    Instrument Cluster Light Bulbs
    The instrument clusters installed on these models are one of 2 types and distinguished by the instrument lighting color, either green or blue.
    On models with green instrumentation, only the control light bulbs are replaceable. Should any other failure occur, the instrument cluster must be replaced.
    On models with blue instrumentation, none of the components are replaceable. Should a failure occur, the instrument cluster must be replaced.

    Map Lights
    1. Disconnect the negative battery cable.
    2. Remove the bulb from its electrical connector.
    3. Installation is the reverse of removal.

    Feb 19, 2011 | 2002 Volkswagen Passat

    1 Answer

    Change out a taillight

    You want to change the tail light bulb?

    The process for replacing tail light bulbs is the same in all models. If you have a burnt-out tail light bulb, you may need to replace the brake light, the reverse light or the turn signal. The procedure to replace each of the bulbs is the same.


      1. Open the Hummer's rear swing gate. This will expose the edge of the vehicle's tail light assembly. You'll see two small Phillips head screws that hold the tail light assembly in place. Put on your gloves.

      2. Remove the two screws from the tail light assembly. Pull the tail light out and inspect the back for two bulbs. The top bulb is the brake light and turn signal. The bottom bulb is the reverse bulb. Determine which bulb you need to replace.

      3Rotate the bulb's socket counterclockwise to disconnect it. Unplug the bulb from its socket.

      4Push the replacement bulb into its socket firmly. Insert the socket back into the tail light. Turn it clockwise to secure it in place.

      5Place the tail light into its cradle. Hold it with one hand and replace the Phillips head screws with the other.

    Dec 03, 2010 | 2008 Hummer H3

    1 Answer

    2000 pontiac montana. I want to replace the driving ligh bulbs. the under the headlights what size is it?

    Fog/Driving Light Bulb Size: 880
    Here is the rest of the bulb size used in your Montana.
    2000 Pontiac Montana Auto Light Bulb Diagram
    Low Beam Headlight Bulb Size: 9004
    High Beam Headlamp Light Bulb Size: 9004
    Parking Light Bulb Size: 4157NALL
    Front Turn Signal Light Bulb Size: 4157NALL
    Rear Turn Signal Light Bulb Size: 3156
    Tail Light Bulb Size: 3057
    Stop Light Bulb Size: 3057
    High Mount Stop Light Bulb Size: Assembly
    Fog/Driving Light Bulb Size: 880
    License Plate Light Bulb Size: 168
    Back Up Light Bulb Size: 3156
    Front Sidemarker Light Bulb Size: 194
    Ash Tray Light Bulb Size: 558
    Glove Box Light Bulb Size: 194
    Map Light Bulb Size: 168
    Dome Light Bulb Size: 562
    Step/Courtesy Light Bulb Size: 168
    Trunk/Cargo Area Light Bulb Size: 212-2
    Daytime Running Light Bulb Size: 3157NALL
    Thank you for using fixya.

    Apr 30, 2010 | 2000 Pontiac Montana

    3 Answers

    1994 Acura vigor gear indicator light won't light D4. All other gear indicator lights work. Happened after replacing two dash lights


    Jun 14, 2009 | 1992 Acura Vigor

    1 Answer

    How to replace headlight on a 2003 Chevy Tracker

    There are two black plastic clips behind the the air filter, remove them and release the whole assembly to access the lights.

    If you still get in troubles, have it replaced at a petrol station, they will help you in fitting the bulb, and it won't be expensive.

    Here follows
    2003 Chevrolet Tracker Light Bulb Size Chart
    Low Beam Headlight Bulb Size: 9003/HB2
    High Beam Headlamp Light Bulb Size: 9003/HB2
    Parking Light Bulb Size: 1157A
    Front Turn Signal Light Bulb Size: 1157A
    Rear Turn Signal Light Bulb Size: 921
    Tail Light Bulb Size: 7443
    Stop Light Bulb Size: 7443
    High Mount Stop Light Bulb Size: 168 Or 921
    License Plate Light Bulb Size: 168
    Back Up Light Bulb Size: 921
    Front Sidemarker Light Bulb Size: 194
    Ash Tray Light Bulb Size: 74
    Step/Courtesy Light Bulb Size: 168
    Trunk/Cargo Area Light Bulb Size: 168
    Instrument-General Light Bulb Size: 158 or 74
    Check Engine Indicator Light Bulb Size: 74
    Hi-Beam Indicator Light Bulb Size: 74
    Seat Belt Indicator Light Bulb Size: 74
    Brake Warning Light Bulb Size: 74
    Automatic Transmission Indicator Light Bulb Size: 74
    Directional Signal Indicator Light Bulb Size: 74

    Oct 02, 2008 | 2003 Chevrolet Tracker

    Not finding what you are looking for?
    2002 Chevrolet Corvette Logo

    Related Topics:

    22 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts


    Level 3 Expert

    77499 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22306 Answers

    Ronny Bennett Sr.
    Ronny Bennett Sr.

    Level 3 Expert

    6927 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides