Question about 2000 Mitsubishi Eclipse

1 Answer

Will not go in gear - 2000 Mitsubishi Eclipse

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Mitsubishi Master
  • 75,077 Answers

Then the transmission has failed and will need to be removed and rebuilt.

Posted on Nov 06, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Noise when shifting gears


transmission synchronizers most common cause of transmisson noise in certain gears, and not others, might want to check the gear oil level. Transmission rebuild required. To read about them and what they actually do, then here is a good read:
When you shift gears in your standard shift car, you move a rod that moves a fork that engages the gear. Depending which gear you're shifting to, a different fork does the job. The fork moves the collar to the desired gear, and dog teeth on the collar mesh up with holes on the gear in order to engage it. You engage reverse gear through a separate, small idler gear. The reverse gear always turns in the opposite direction of the other (forward) gears.
In years past, double-clutching was common in order to disengage a gear, allow the collar and next gear to reach the same speed, and then to engage the new gear. To double-clutch shift, you pushed the clutch pedal to free the engine from the transmission. Then the collar moved into neutral. You released the clutch and revved the engine to get it to the right rpm value for the next gear so the collar and the next gear spun at the same rate to allow the dog teeth to engage the gear. When the engine hit the right speed, you depressed the clutch again in order to lock the collar into place on the next gear.
Modern cars use synchronizers in order to avoid the need for double-clutching. A synchronizer, or "synchro," lets the collar and gear synchronize their speeds while they're already in contact but before the dog teeth engage. Each manufacturer's synchro is slightly different than the others, but the basic idea is the same. For instance, a cone on one gear will fit into a cone-shaped depression on the collar. The gear and collar synchronize their speeds thanks to the friction between the cone and collar. Then the outer part of the collar moves out of the way so that the gear can be engaged by the dog teeth.

Dec 16, 2013 | Chevrolet Silverado 2500HD Cars & Trucks

1 Answer

My 99 z24 cavalier standerd shift it will not shift into 3rd gear


The gear may be stripped, can't catch other gear,have you been grinding this gear,will have to go into transmission and replace third gear, will have to wind second gear out and shift to 4th gear.May be better and cheaper to get a remanufactured transmission cause all parts are new versus just 3rd gear being replaced.

Dec 24, 2012 | 1999 Chevrolet Cavalier

1 Answer

I have a 88 Ford Bronco2.9Liter 4wheel drive Mitsubishitransmission. I need a diagram of tranny for the gears.


It's very simple starting at the front of the tranny going to the rear if it's a 4 speed
all of the gears except the input shaft (4th gear ) will be assembled on the main shaft ,,,
from small to large on the main shaft
the input shaft is the 4th gear , next is 3rd gear , next is 2nd gear, and then 1st gear is the largest

now the counter shaft in the bottom of the case ,,, it 's gear labeling will be backwards from large to small
like this

the front of the countershaft is large and mates with the small gear(4th)
the next gear is 3rd, then 2nd, then 1st,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,, the gear thats mounted off the side in the case is the reverse idler

If its a 5 speed

the gears places above are the same and 5th gear is added to the rear of the main shaft (,the smallest gear,)

the gears on the countershaft are the same and 5th gear is the last gear on the countershaft( the largest gear on the counter shaft ) the single gear mounted off the side in the case is the reverse idler

hope this helps

Mar 14, 2011 | Ford Bronco II Cars & Trucks

1 Answer

Sounds like there could be gear damage in 5th gear. Isn't 5th gear a straight through arrangement? G. Nye


All the gears inside the transmission are driven off a main gear called a cluster gear. Though the gear ratio changes as you select different gears, each "gear" you select engages several gears inside the unit to achieve the one you selected. Actually if it was possible to have a straight through arrangement, that would happen in fourth gear. Fifth is overdrive... the input actually turns slower than the output so the engine turns slower and saves fuel.

Feb 21, 2011 | 1992 Jeep Wrangler

1 Answer

94 caprice classic rear spider gears shot 12 or 16 possi what other rear ends are compatible for this 5.7 liter





. Axle Code >>>>>>>>>>>Standard
2YN Gear Ratio >>>>2.56<<<<< Ring Gear Diameter 8.5 Standard 2GA Gear Ratio 2.73 Ring Gear Diameter 7.6 Standard 2GB Gear Ratio 2.73 Ring Gear Diameter 7.6 Standard 2GH Gear Ratio 2.73 Ring Gear Diameter 8.5 Standard 2LW Gear Ratio 3.08 Ring Gear Diameter 8.5 Standard 2LR Gear Ratio 3.23 Ring Gear Diameter 8.5 Standard 2LY Gear Ratio 3.23 Ring Gear Diameter 8.5 Standard 2LT Gear Ratio 3.23 Ring Gear Diameter 8.5 Standard 6YF Gear Ratio 3.23 Ring Gear Diameter 8.5


Axle Code>>>>>>>>> Limited Slip
2LQ Gear Ratio >>>>>>>>2.93<<<<<<<<<<< Ring Gear Diameter 8.5 Limited Slip 2YG Gear Ratio 2.93 Ring Gear Diameter 8.5 Limited Slip 2LX Gear Ratio 3.08 Ring Gear Diameter 8.5 Limited Slip 2ND Gear Ratio 3.23 Ring Gear Diameter 8.5 Limited Slip 2LZ Gear Ratio 3.23 Ring Gear Diameter 8.5 Limited Slip 2LS Gear Ratio 3.23 Ring Gear Diameter 8.5

Nov 28, 2010 | 1994 Chevrolet Caprice Classic

1 Answer

How do you know what ratio a subaru wrx gearbox is if it doesn't have a trans code sticker on it?


This information is from my genuine service manual. I hope it is of help.
Non-turbo
Turbo
Sedan Wagon
Type 5-forward speeds with synchromesh and 1-reverse
Transmission gear ratio
1st 3.454 3.454
2nd 2.062 1.947
3rd 1.448 1.366
4th 1.088 0.972
5th 0.780 0.738
Reverse 3.333
Front reduction gear Final
Type of gear Hypoid
Gear ratio 4.111 3.900
Rear reduction gear
Transfer
Type of gear Helical
Gear ratio 1.000 1.100
Final
Type of gear Hypoid
Gear ratio 4.111 3.900 3.545
Front differential Type and number of gear Straight bevel gear (Bevel pinion: 2, Bevel gear: 2)
Center differential Type and number of gear
Straight bevel gear
(Bevel pinion: 2, Bevel gear: 2 and viscous coupling)
Transmission gear oil GL-5
Transmission gear oil capacity 3.5 2 (3.7 US qt, 3.1 Imp qt)

Mar 21, 2010 | 2007 Subaru Impreza WRX Sport Wagon

1 Answer

GEAR SHIFTING CAMRY 2004 2.4 XLI


Hi,

This might be because of the gear box problem. By any chance, did your car face flooding? In such cases, please drain the gear box and replace it with new gear fluids. Also, check if you go in low speeds, you might be able to engage it with ease. Please come back to me if you feel this doesnt solve your issue.

Regards,
Hari

Aug 27, 2009 | 1998 Jeep Grand Cherokee

2 Answers

Need a drawing of the worm shaft and spool valve assy.


closest I have is 94 explorer. may be similar.

d097a7d.gif
058382f.gif
0eb9efd.gif
Item Part Number Description 1 3E501 Steering Gear Sector Shaft Seal 2 3524 Steering Gear Input Worm Gear and Rack 3 3647 Steering Gear Worm Ball 4 3523 Steering Gear Ball Return Guide 5 3A670 Steering Gear Worm Thrust Bearing Adjuster 6 — Locknut (Part of 3577) 7 3571 Steering Gear Worm Thrust Bearing 8 3575 Steering Gear Sector Shaft 9 3524 Steering Gear Input Worm Gear and Rack

May 09, 2009 | 1983 Ford F 250

Not finding what you are looking for?
2000 Mitsubishi Eclipse Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...