Question about Cars & Trucks

1 Answer

How to take of oil pan - Cars & Trucks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 75,797 Answers

Duplicate question.

Posted on Nov 06, 2012


1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacement of the oil pan on a cadillac 2006 DTS


Big job.

gmlogoflat.gif Service Information
bhome.gifbpublication.gifbnumsrchbutton.gifbnews.gifymkbutton.giffeedback.gifbhelp.gif
2006 Cadillac DTS ' DTS VIN K Service Manual ' Document ID: 636855 Oil Pan Removal

    1527739.gif
    tif.gif
  1. Rotate the engine so that the oil pan is facing up.
  2. Remove the oil pan drain plug.

  3. 1373472.gif
    tif.gif
  4. Remove the oil pan bolts.

  5. 1373475.gif
    tif.gif
  6. Remove the oil pan from the lower crankcase oil distribution manifold plate.

  7. 1373484.gif
    tif.gif
  8. Remove and discard the oil pan gasket.

  9. 204585.gif
    tif.gif
  10. Remove the oil level sensor (1).

Jul 29, 2011 | 2006 Cadillac DTS

1 Answer

How to do a transmission fluid/filter change on a gmc 1500 2wd v8 350 step by step


Raise the vehicle. Refer to Vehicle Lifting. Place a drain pan under the transmission oil pan. Remove the oil pan drain plug. Remove the oil pan bolts. Remove the oil pan. Remove the gasket. Remove the magnet. Remove the oil filter. Remove the filter neck seal. The transmission oil pan gasket is reusable. Inspect the gasket and replace as needed. Clean the transmission case and the oil pan gasket surfaces with solvent. Install the filter neck seal. Install the oil filter. Install the oil pan gasket to the pan. Install the magnet into the bottom of the pan. Notice: Refer to Fastener Notice in Service Precautions. Install the oil pan to the transmission with seventeen bolts. Tighten the oil pan bolts to 11 Nm (97 inch lbs.) . Apply a small amount of sealant GM P/N 12346004 to the treads of the drain plug. Install the oil pan drain plug. Tighten the oil pan drain plug to 18 Nm (13 ft. lbs.) . Install Dextron Automatic Transmission Fluid. Lower the vehicle.

Jul 04, 2011 | GMC Sierra 1500 Cars & Trucks

2 Answers

How difficult is it to change the oil pan on a 1997 gmc jimmy 4x4?


4WD To Remove:
  1. Remove or disconnect the following:
    • Negative battery cable
    • Oil level indicator
    • Front differential assembly
    • Starter
    • Transmission cover
    • Oil pan drain plug and drain the engine oil into a suitable container
    • Remote oil filter pipe adapter
    • Remote oil filter hose clip bolt on oil pan
    • Starter wire harness bracket stud
    • Transmission oil cooler pipes (if equipped)
    • Access plugs for oil pan rear nuts
    • Transmission to oil pan bolts
    • Oil pan nuts and bolts gm_truck_43_ol-pn_ol-lvl-snsr.gif

      NOTE: The low oil level sensor is not reusable.
    • Remove and discard the engine oil level sensor (if applicable) gm_truck_43_ol-pn_blts.gif

    • The oil pan
    • The oil pan gasket
  2. Discard the oil pan gasket.
  3. Clean all sealing surfaces on the engine and the oil pan.
To Install:
Note: Whenever the transmission and the engine oil pan are removed from the engine at the same time install the transmission before the oil pan. This is to allow for the proper oil pan alignment. Failure to achieve the correct oil pan alignment can result in transmission failure.
  1. Apply a 0.197 inch (5 mm) wide and 1.0 inch (25 mm) long bead of adhesive GM P/N 12346141 (Canadian P/N 10953433) or equivalent to both the right and left sides of the engine front cover to engine block junction at the oil pan sealing surfaces. gm_truck_43_ol-pn_ahsv_loc_f.gif

    gm_truck_43_ol-pn_ahsv_loc_r.gif

  2. Apply a 0.197 inch (5 mm) wide and 1.0 inch (25 mm) long bead of adhesive GM P/N 12346141 (Canadian P/N 10953433) or equivalent to both the right and left sides of the crankshaft rear oil seal housing to engine block junction at the oil pan sealing surfaces. Note: Always install a new oil pan gasket. The oil pan gasket and oil pan must be installed and the fasteners tightened while the adhesive is still wet to the touch.
  3. Install the new oil pan gasket into the groove in the oil pan. Note: The oil pan alignment must always be flush or forward no more than 0.011 inch (0.3mm) from the rear face of the engine block.
  4. Install or connect the following:
    • The oil pan onto the engine block
      1. Press the oil pan gasket into the grooves of the engine front cover and crankshaft rear oil seal housing
      2. Slide the oil pan back against a suitable straight edge
    • The oil pan bolts and nuts, but do not tighten
  5. Measure the pan-to-transmission housing clearance using a feeler gage and a straight edge. gm_truck_43_ol-pn_trnz_clrc.gif

    • Use a feeler gage to check the clearance between the oil pan-to-transmission housing measurement points
      1. If the clearance exceeds 0.011 inch 0.3mm) at any of the 3 oil pan-to-transmission housing measurement points (A), then repeat the step until the oil pan-to-transmission housing clearance is within the specification
      2. The oil pan must always be forward of the rear face of the engine block
    gm_truck_43_ol-pn_trq-sqc.gif

  6. Tighten the oil pan bolts and nuts in sequence
    • Torque to: 18 ft lb (25 Nm).
  7. Measure the clearance between the 3 oil pan-to-transmission housing measurement points in order to ensure proper alignment.
  8. Install or connect the following:
    • A new oil pan drain plug seal (O-ring) onto the oil pan drain plug
    • Oil pan drain plug into the oil pan
      1. Torque to: 18 ft lb (25 Nm)
      NOTE: The low oil level sensor is not reusable.
      gm_truck_43_ol-pn_ol-lvl-snsr.gif

    • New low oil level sensor
      1. Torque to: 115 in lb (13 Nm)
    • Transmission to oil pan bolts.
      1. Torque to: 35 ft lb (47 Nm)
    • Access plugs for the oil pan rear nuts
    • Starter wire harness bracket stud
    • Transmission oil cooler pipes (if equipped)
    • Remote oil filter pipe adapter
    • Oil filter hose clip bolt to the oil pan
    • Transmission cover and bolts.
    • Starter motor
    • Front differential assembly
    • Oil level indicator
  9. Fill the engine with oil.
  10. Connect the negative battery cable.

Dec 19, 2010 | 1997 GMC Jimmy

1 Answer

Oil pump ,,,where is the oil pump located on a 1997 dodge caravan


Hello
Welcome!
Oil pump is located on the oil pan.
Parts needed,,,oil,,,, oil filter,,,, oil pan gasket,,, oil pump,,,, oil pump pickup tube..
time to do this,, about 3 hours
Instructions,
Raise van place on 2 jack stands
drain oil remove oil filter fill new filter install.
remove bolts from oil pan,
remove oil pan..
remove 2 bolts that hold oil pump and tube.

install new pump and tube tork bolts to 45 fp
replace oil pan gasket and install oil pan
tork pan bolts to 35" pounds
install drain plug
fill with oil
start and check for leaks

let me know if i can help more

Jul 17, 2010 | 1997 Dodge Caravan

1 Answer

Oil pan


Replacing an Oil Pan Gasket
  • Drain oil through plug located at the bottom of oil pan.
  • Remove bolts around edge of the oil pan. There are probably around 8 of them.
  • Drop oil pan.
  • Clean gasket material from both block and oil pan.
  • Install new gasket.

Mar 12, 2010 | 1992 Honda Accord

1 Answer

Oil pan leak


buy a tube of sealer called Right Stuff
1. Remove the flexible exhaust pipe
2. Disconnect the downstream catalyst monitor sendor (OXYGEN SENSOR)
3. Drain engine oil
4. Remove the 15 bolts and the oil pan
5. Clean pan & surface area.
6. Apply sealer 10mm (0.40 inch) diameter of sealer
7. Position oil pan and hand-tighten the oil pan bolts
8. Start with front of oil pan tighten each bolts going around oil pan till all are tighten up.
9. Install exhaust flexible exhaust pipe
10. Connect OXYGEN SENSOR connector
11. Lower the vehicle.
12. Fill oil 5w20 (Spec)

Feb 10, 2010 | 2001 Ford Escape

3 Answers

The car is leaking oil and the mechanic said it was because there is a whole in the oil pan and it will cost 1800 to fix. can i buy another oil pan and put it on myself?


OIL PAN
REMOVAL
Drain engine oil.
Remove front engine mount bracket.
Remove power-train bending strut.
Remove structural collar from oil pan to trans-axle Structural Collar - Removal and Installation
Remove trans-axle lower dust cover.
If equipped with air conditioning, remove oil filter and adapter.
Remove oil pan.
Clean oil pan and all gasket surfaces.
INSTALLATION
Apply Mopar® Silicone Rubber Adhesive Sealant or equivalent at the oil pump to engine block parting line Oil Pan Sealing
Install a new oil pan gasket to pan.
Install pan and tighten screws to 12 N·m (105 in. lbs.)
Install oil filter and adapter.
Install trans-axle lower dust cover.
Install power-train bending strut.
Install front engine mount and bracket
CAUTION: The torque procedure for the structural collar must be followed, as damage to oil pan or collar could occur.

Install the structural collar Structural Collar - Removal and Installation using the following 3 step torque sequence:
Step 1: Install the collar to oil pan bolts and tighten to 3 N·m (30 in. lbs.)
Step 2: Install collar to trans-axle bolts and tighten to 108 N·m (80 ft. lbs.)
Step 3: Final torque the collar to oil pan bolts to 54 N·m (40 ft. lbs.)
Fill engine crankcase with proper oil to correct level.

Auto Zone carries the Oil pan you need for around $75.00 and they will have the step by step instructions for you to replace the oil pan. will take just over 2 hours for the average person. Good luck and keep me posted.

Nov 30, 2009 | 2002 Dodge Neon

1 Answer

Replace oil pan gasket 2002 chrysler 300m


The owner of the car should be able to locate and replace oil pan gasket .prepare the equipment to be used .Drain the oil from the oil pan ,spill it to an empty big can that can carry the oil from the oil pan.Then twist the bolts that connect the oil pan to the engine.After removing the bolts then you have take the old gasket off to the oil pan.After taking off the old gasket then you have to replace it with the new oil pan gasket.then return the oil pan with the new gasket. twist the bolt back until the oil pan that connect the oil pan with the engine.And return the drain plug twist until it will not spill.

Sep 30, 2009 | 2001 Chrysler 300M

1 Answer

How do I change the tranny fluid in my 1998 cadillac catera


Fluid - A/T: Service and Repair
Transmission Fluid and Oil Filter Changing
REMOVAL PROCEDURE
1. Raise and suitably support the vehicle. Refer to Vehicle Lift Points.
2. Place drain pan under pan
3. Remove oil pan bolts from front and sides only.
4. Loosen the rear oil pan bolts approximately four turns.
5. Lightly tap the oil pan with a rubber mallet or pry to drain the fluid from main case.
6. Remove the oil pan bolts from rear oil pan and gasket.
7. Remove front oil pan bolts leaving one corner bolt in loosely.
8. Lightly tap oil pan with rubber mallet or pry to drain fluid.
9. Remove the following remaining components:
^ The front oil pan bolts
^ The oil pan
^ The gasket
10. Remove the oil filter bolts and filter.
11. Clean the following components:
^ The transmission case
^ The front adapter case
^ The oil pan gasket surfaces with solvent
^ Air dry
^ All traces of gasket material must be removed
INSTALLATION PROCEDURE
1. Install the gasket.
2. Install the oil filter.
3. Install the bolts.
^ Tighten the transmission oil filter bolts to 20 Nm (15 ft. lbs.).
NOTICE: Refer to Fastener Notice in Service Precautions.
4. Install the front oil pan.
5. Install the front oil pan gasket
6. Install the front oil pan bolts
^ Tighten the front oil pan bolts to 11 Nm (96 inch lbs.).
7. Install the following components:
^ Install the pan
^ Install the gasket
^ Install the bolts
^ Tighten the oil pan bolts to 11 Nm (96 inch lbs.).
8. Refill the transmission with DEXRON III through oil pan fill plug on the side of the (main case) oil pan. Fill the transmission to lower edge of oil
pan fill. Fill plug opening using and oil suction gun.
^ Tighten the oil pan fill plug to 45 Nm (33 ft. lbs.).
9. Lower the vehicle.
10. Check the transmission fluid level. Refer to Transmission Fluid Checking Procedure.

Sep 13, 2009 | 1998 Cadillac Catera

2 Answers

05 susuki forenza


Removal Procedure
1. Disconnect the negative battery cable.
2. Drain the engine oil from the engine crankcase.
3. Remove the exhaust flex pipe retaining nuts from
the exhaust manifold.
4. Remove the exhaust flex pipe retaining nuts from
the catalytic converter or the connecting pipe.
5. Remove the exhaust flex pipe.
6. Remove the oil pan flange–to–transaxle retaining
bolts.
7. Remove the oil pan retaining bolts.
8. Remove the oil pan from the engine block.
Cleaning Procedure
1. Clean the oil pan sealing surface.
2. Clean the engine block sealing surface.
3. Clean the oil pan retaining bolts.
4. Clean the oil pan attaching bolt holes in the engine
block.
5. Clean the oil pan scraper.
Installation Procedure
1. Coat the new oil pan gasket with sealant.
Important : Install the oil pan within 5 minutes after applying
the liquid gasket to the oil pan.
2. Install the oil pan to the engine block.
3. Install the oil pan retaining bolts.
Tighten
Tighten the oil pan retaining bolts to 10 NSm (89 lb–in).
4. Install the oil pan flange–to–transaxle retaining
bolts.
Tighten
Tighten the oil pan flange–to–transaxle bolts to 40
NSm (30 lb–ft).
5. Install the exhaust flex pipe.
6. Install the exhaust flex pipe retaining nuts to the
exhaust manifold.
Tighten
Tighten the exhaust flex pipe–to–exhaust manifold
retaining nuts to 35 NSm (26 lb–ft).
7. Install the exhaust flex pipe retaining nuts to the
catalytic converter or the connecting pipe.
Tighten
Tighten the exhaust flex pipe–to–catalytic converter
or connecting pipe retaining nuts to 35 NSm (26 lb–ft).
8. Connect the negative battery cable.
9. Install the oil pan drain plug.
Tighten
Tighten the oil pan drain plug to 35 NSm (26 lb–ft).
10. Refill the engine crankcase with engine oil.

Jun 14, 2008 | 2005 Suzuki Forenza

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...