Question about Nissan Cars & Trucks

1 Answer

How do I remove the steering cover to chnge the multifunction switch 2005 altima?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Nissan Master
  • 75,130 Answers

Duplicate question

Posted on Nov 06, 2012

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

ndguy2481
  • 251 Answers

SOURCE: Replace multifunction switch on Pontiac Gran Prix 2000

no just the top and bottom of the steering wheel cover

Posted on Dec 07, 2008

  • 4044 Answers

SOURCE: Removing the door panel on a 2005 Nissan Altima

If you have the door panel loose you should be able to see the plastic clips that are holding that in or a plug you can undo to be able to remove the panel completely. If it has clips you can release them with a screw driver.

Posted on Dec 03, 2009

  • 4793 Answers

SOURCE: Replacing low beam headlight on 2005 altima

it is a twist and pull cover....

Posted on Jun 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Multifunction switch


No, just remove upper and lower trim pieces that cover the steering wheel. Unscrew the switch and disconnect it. Be sure to disable the airbag or SIR module in there. Don't want that airbag deploying.

Feb 01, 2014 | Chevrolet TrailBlazer Cars & Trucks

1 Answer

How to replace the wiper switch in a 2005 chevy trail blazer


YOU HAVE TO REPLACE WHOLE MULTIFUNCTION SWITCH WITH TURN SIGNAL SWITCH, LIGHT SWITCH, WIPER SWITCH HAS TO BE REPLACED.YOU HAVE TO TURN OFF RADIO FIRST THEN REMOVE NEGATIVE BATTERY CABLE.THEN WAIT 20 MINUTES UNTIL AIRBAG IN STEERING WHEEL DISARM.THEN REMOVE THE MULTIFUNCTION SWITCH LOCATED ON THE LEFT SIDE OF THE STEERING COLUMN.YOUR WIPER SWITCH ON THE MULTIFUNCTION SWITCH.

Aug 16, 2011 | 2005 Chevrolet TrailBlazer

1 Answer

How to change turn signal switch on 98 chevy lumina


buy a new multifunction switch
rent a steering wheel puller
remove airbag fuse
remove cosmetic steering wheel cover
remove airbag
remove steering wheel
replace switch
replace steering wheel
replace cosmetic cover
replace fuse

Jun 30, 2011 | 1998 Chevrolet Lumina

1 Answer

How do i install Switch Assembly turn signal Cruise control PART AUTO for a 2002 Impala.


Multifunction Turn Signal Lever Replacement - On Vehicle

Removal Procedure

83422682


  1. Verify that the multifunction turn signal lever is in the center of the OFF position.
  2. Disconnect the negative battery cable.
  3. Disable the SIR system.
  4. Remove the steering wheel.
  5. Remove the steering column trim cover.
  6. Remove the steering column knee bolster.
  7. Remove the steering column wire harness (1) from the steering column wire harness retainer (2).
  8. Remove the 2 wire harness straps from the steering column wire harness (1).
  9. Remove the steering column bulkhead connector from the vehicle wire harness.
  10. Disconnect the connectors from the multifunction turn signal lever steering column bulkhead connector.
85097560




  1. Remove the retaining bolts (1) from the multifunction turn signal lever (2).
  2. Remove the multifunction turn signal lever (2) from the steering column.
Installation Procedure

85097560




  1. Install the multifunction turn signal lever (2). Use a small flat-blade in order to compress the electrical contact and move the multifunction turn signal lever into position.
  2. Verify that the electrical contact rests on the canceling cam.
Notice: Refer to Fastener Notice in Service Precaution.


  1. Install the retaining bolts to the multifunction turn signal lever.
    • Tighten the retaining bolts to 7 Nm (62 inch lbs.) .
92905224




  1. Connect the gray and black connectors to the multifunction turn signal lever steering column bulkhead connector.
  2. Connect the steering column bulkhead connector to the vehicle wire harness.
  3. Install the two wire harness straps to the steering column wire harness (1).
  4. Install the steering column wire harness (1) to the steering column wire harness retainer (2).
  5. Install the steering column knee bolster.
  6. Install the steering column trim cover.
  7. Verify that the lever is in the center or the OFF position.
  8. Install the steering wheel to the steering column.
  9. Enable the SIR system.
  10. Connect the negative battery cable.
I hope this helps you.

Thanks

Nov 28, 2010 | 2002 Chevrolet Impala

1 Answer

How do I remove the turn signal/light switch from a 94 Mercury tracer.


TURN OFF RADIO FIRST TO KEEP FROM LOCKING IT OUT.DISCONNECT NEGATIVE BATTERY CABLE WAIT 20 MINUTES FOR AIRBAG TO DISCHARGE THEN.REMOVE STEERING WHEEL COVER RETAINING SCREWS FROM THE BACK SIDE OF THE STEERING WHEEL AND REMOVE THE COVER.DISCONNECT THE HORN ELECTRICAL CONNECTOR AND THE SPEED CONTROL ELECTRICAL CONNECTORS IF EQUIPPED.REMOVE THE STEERING WHEEL MOUNTING NUT OR BOLT.YOU NEED A STEERING WHEEL PULLER TO REMOVE STEERING WHEEL DONT USE A HAMMER ON STEERING WHEEL BECAUSE IT WAS FACTORY MADE TO COLLAPSE DURING A CAR ACCIDENT.IF HIT STEERING WHEEL WITH HAMMER IT WILL COLLAPSE.USE STEERING WHEEL PULLER YOU CAN BUY ONE AT SEARS AUTO TOOLS OR SNAP ON TOOLS ALSO MOST AUTO PARTS STORE CARRY IT ALSO.OKAY AFTER REMOVING STEERING WHEEL.REMOVE THE 4 RETAINING SCREWS FROM THE STEERING COLUMN LOWER COVER AND REMOVE THE COVER REMOVE THE UPPER COVER.DISCONNECT THE 3 MULTIFUNCTION SWITCH ELECTRICAL CONNECTORS.REMOVE THE MULTIFUNCTION SWITCH RETAINING SCREW PULL THE ELECTRICAL CONNECTORS FROM THE RETAINING BRACKETS AND REMOVE THE SWITCH.INSTALL EVERYTHING VISA VERSA.TORQUE STEERING WHEEL MOUNTING BOLT TO 34 - 46 FT LBS.

Oct 15, 2010 | 1994 Mercury Tracer

1 Answer

How do I replace the signal switch assembly on my 2004 Chevy Cavalier?


Before servicing any electrical component, the ignition key must be in the OFF or LOCK position and all electrical loads must be OFF , unless instructed otherwise in these procedures. If a tool or equipment could easily come in contact with a live exposed electrical terminal, also disconnect the negative battery cable. Failure to follow these precautions may cause personal injury and/or damage to the vehicle or its components.
  1. Disconnect the negative battery cable.
  2. Remove the steering column trim covers.
  3. Remove the retaining screws from the multifunction switch.

    0996b43f802054ac.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Remove the multifunction switch (2) from the steering column

  4. Remove the multifunction switch from the steering column.
  5. Disconnect the electrical connectors from the multifunction switch.

To install:
  1. Connect the electrical connectors to the multifunction switch.
  2. Install the multifunction switch to the steering column while depressing the spring loaded horn pin.
    NOTE Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
  3. Install the retaining screws to the multifunction switch and tighten the screws to 36 lb inches (4 Nm).
  4. Install the steering column trim covers.
  5. Connect the negative battery cable.
  6. Ensure that the multifunction switch functions properly.

Sep 27, 2010 | 2004 Chevrolet Cavalier

1 Answer

Multifunction Switch works intermittantly. When the blinkers and wipers stop, have to Bang on the steering column, then it works again. Goes in spurts, have to bang for a week or 2, then it works fine...


Multifunction Switch -I suspect this switch or the connection at the harness is bad or contaminated. Removal & Installation To Remove:
  1. Disconnect and isolate the negative battery cable.
  2. Remove the upper and lower steering column shrouds.
  3. Disconnect wire connector from the back of the multifunction switch.
  4. Remove screws holding multi-function switch to steering column adapter collar.
  5. Remove the multi-function switch.
To Install:
  1. Position the switch on to the steering column and install the mounting screws.
  2. Connect the electrical connectors to the switch.
  3. Install the upper and lower steering column shrouds.
  4. Connect the negative battery cable.
prev.gif next.gif

Aug 17, 2010 | 2005 Chrysler Town & Country

1 Answer

Remove ignition switch for a 2004 kia optima


Ignition Switch Removal & Installation To Remove:
  1. Disconnect battery negative cable.
  2. Disarm air bag system.
  3. Remove driver air bag module.
  4. Loosen screw and lift horn pad to remove.
  5. Remove lock nut and washer. CAUTION
    Do not hammer on steering wheel. Damage can occur to the energy absorbing portion of the steering column.
  6. Pull dynamic damper forward and lift up to remove.
  7. Remove steering wheel.
  8. Remove steering column shrouds.
  9. Remove lower cover.
  10. Remove multifunction switch.
  11. Remove entire lower portion of dash.
  12. Remove mounting fasteners and lower steering column.
  13. Remove bolts and separate ignition switch from steering column.
To Install:
  1. Install ignition switch to steering column and install bolts.
  2. Raise steering column and install mounting fasteners.
  3. Install lower portion of dash.
  4. Install multifunction switch.
  5. Install lower cover.
  6. Install steering column shrouds.
  7. Install steering wheel.
  8. Install dynamic damper.
  9. Install washer and lock nut.
  10. Lift horn pad and install screw.
  11. Install driver air bag module.
  12. Connect battery negative cable.
prev.gif next.gif

Jul 17, 2010 | 2004 Kia Optima

1 Answer

I need to install my cruise control switch on my steering wheel . How do I go about removing the back cover on the steering wheel?


Removal & Installataion
  1. Verify that the multifunction turn signal lever is in the center of the OFF position.
  2. Disconnect the negative battery cable.
  3. Disable the SIR (air bag) system. Refer to the Chassis Electrical Section.
  4. Remove the air bag module from the steering wheel.
  5. Remove the steering wheel.
ca4e20e.gif
Exploded view of the shroud-type steering column showing shrouds, wiring and multifunction switch that includes the headlamp function

    1. Remove the upper and lower steering wheel trim covers using the following procedure.
    2. Remove the tilt lever assembly.
    • Remove the two pan head tapping screws from the lower shroud.
    • Unlock the upper and lower shroud.
    • Remove the two Torx® head screws from the upper shroud.
    • Remove the upper shroud.
    1. Remove the wire harness straps from the wire harness assembly and detach the wiring harness connectors from the switch side connectors.
    2. Remove the two multifunction turn signal switch screws and remove the multifunction switch assembly from the vehicle.
    To install:
    1. Install the multifunction switch to the steering column. Use a small flat-blade prytool to compress the electrical contact and move the multifunction turn signal switch into position. Verify that the electrical contact rests on the canceling cam. Install the screws and tighten to 62 inch lbs. (7 Nm).
    2. Route the wire harness along the steering column jacket assembly and secure into the wire harness strap. Install a new wire tie to the upper tilt head assembly and another lower along the wiring harness, as the original installation.
    3. Verify that the lever is in the center of the OFF position.
    4. Install the upper and lower steering column shrouds.
    5. Route the SIR connector through the steering wheel, align the scribe mark on the steering wheel made at removal, with the slash mark on the steering shaft and install the steering wheel. Install the steering shaft nut and torque to 30 ft. lbs. (41 Nm).
    6. Install the horn contact leads and the air bag connector to the back of the air bag. Make sure the CPA wedge is in place to secure the connector. Install the air bag by gently pushing on both the right and left sides of the air bag until the retaining springs engage.
    7. Enable the SIR system by connecting the yellow 2-way connector at the base of the steering column and installing the air bag fuse.
    8. Connect the negative battery cable. Test the horn, turn signals and headlight operation.
    1. Disable the SIR system.
    2. Remove the upper and lower trim covers.
    3. Remove the knee bolster.
      NOTE The abrasion sleeve located on the steering column wire harness assembly must be reinstalled. Make note of what connector is coming out of the abrasion sleeve for installation purposes.

    4. Remove the wire harness assembly from the wire harness strap.
    5. Disconnect the turn signal and multifunction switch assembly connector from the SIR system coil connector.
    6. Slide the 2 connectors of the turn signal and multifunction switch assembly out of the bulkhead connector.
    7. Remove the 2 pan head tapping screws and from the turn signal and multifunction switch assembly.
    8. Remove the turn signal and multifunction switch assembly from the steering column tilt head assembly.
    To install:
    NOTE Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

    CAUTION Be sure that the electrical contact of the turn signal and multifunction switch assembly (2) rests on the turn signal cancel cam assembly.

    CAUTION The abrasion sleeve must be installed back onto the steering column wire harness assembly. The ignition lock cylinder case wires and connector must be hanging out of the middle of the abrasion sleeve.

    1. To install, reverse removal procedure.
    2. Tighten the following to specification.
      • Top pan head tapping screw: 27 inch lbs. (3 Nm).
      • Side pan head tapping screw: 62 inch lbs. (7 Nm).
    CAUTION When performing service on or near the SIR components or the SIR wiring, the SIR system must be disabled. Refer to SIR Disabling and Enabling . Failure to observe the correct procedure could cause deployment of the SIR components, personal injury, or unnecessary SIR system repairs.

    Dec 08, 2009 | 2005 Chevrolet Impala

    3 Answers

    How to replace my turn signal switch


    Multi-function Switch Removal & Installation To Remove:
    To Remove:
    1. Remove the steering column trim covers.
    2. Remove the wire harness from the retainers as needed.
    3. Slide the turn signal and multifunction switch connectors out from the bulk head connector.
    4. Remove the two mounting screws and remove the multi-function switch from the steering column.

    To Install:
    1. Install the multi-function switch on the steering column.
      • Tighten the screws to 42 lb in (4.7 Nm).
    2. Slide the turn signal and multifunction switch connectors into the bulkhead connector.
    3. Install the harness in the original retainers.
    4. Install the steering column trim covers.
    7f81df3.gif

    Jun 25, 2009 | 1996 GMC Sierra

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    35 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Nissan Experts

    yadayada
    yadayada

    Level 3 Expert

    75117 Answers

    Phil Lovisek
    Phil Lovisek

    Level 3 Expert

    705 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Are you a Nissan Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...