Question about 2003 Hyundai Santa Fe
2.4 liter engine need diagram
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: need timing belt diagram for
The timing belt diagrams are listed in detail with figures and procedure to remove them.
REPLACING TIMING BELT ON A 2003 HYUNDAI TIBURON 2.7L V6
1. Remove passenger side headlight via the 3 10mm screws holding it in place and disconnect the turn signal and main harness
2. Remove passenger side tire
3. Remove the splash guard via 2 10mm screws at the top of the guard
4. Remove the 2 17mm bolts and 2 17mm nuts from motor mount bar
5. You may have to separate the mount bar from the motor via either a chisel or flathead screwdriver and a hammer ( support engine via a jack and a piece of plywood under oil pan )
6. Use a 3/8 ratchet ( or a long breaker bar would work better ) to remove the serpentine belt ( remember the route ). Disconnect the power steering hose from the pump and secure back with a zip tie. Remove the power steering pulley with a pry bar and 19mm socket.
7. Hand turn the crankshaft via a 22mm socket to TDC ( top dead center, marked on lower timing belt cover )
8. Remove the serpentine belt tensioner via 2 12mm bolts on each side
9. Remove the upper timing belt cover via 7 10mm screws
10. Remove crankshaft pulley ( 22mm ) with an air impact gun ( an electric one will work too )
11. Remove lower timing belt cover via 4 more 10mm screws
12. Remove the motor mount from the block via 3 14mm bolts and 2 12mm bolts ( there is a 12mm holding the oil dipstick bracket towards the front of the car )
13. Remove the auto tensioner via 2 12mm bolts
14. Remove the timing belt
15. Make sure your timing markings are correct...
There is one marking on each cam gear and on the heads ( head markings are small, look closely...try wiping the edge of the head down with a rag and some brake cleaner to bring it out more ) They are also pictured in last pic.
When the crankshaft is in the TDC position, the cam gear markings should both line up at the same time with the head markings
Adjust if necessary, use a 17mm socket to turn cam gears to correct position
16. Install new timing belt ( as you install it, make sure to keep a little tension on the belt as you route it )
17. Install new auto tensioner and pull pin
18. Install just the lower timing belt cover
19. Install the crankshaft pulley
20. Hand turn the crankshaft atleast 5 times to verify the timing markings are lining up properly ( all should line up at the same time when the crankshaft pulley mark is in the TDC position )
21. Remove crankshaft pulley
22. Remove lower timing belt cover
23. Reverse steps 12 - 1
You can refer the videos below for further assistance.Your valuable feedback would be appreciated.Thanks for choosing Fixya.
Posted on Jun 10, 2011
Tips for a great answer:
May 15, 2016 | Toyota Cars & Trucks
Aug 19, 2012 | Cars & Trucks
Apr 01, 2012 | Cars & Trucks
Sep 21, 2011 | 2003 Chevrolet Impala
Dec 15, 2009 | 1989 Chevrolet Corsica
Dec 22, 2008 | 2004 Dodge Ram 1500
Dec 05, 2008 | 1991 Eagle Talon
Nov 23, 2016 | 2003 Hyundai Santa Fe
306 people viewed this question
Usually answered in minutes!