Question about Cars & Trucks

Open Question

I have a problem: i need a code for coolant sensor for kubota 1105 engine...

Coolant temperature sensor 2 conections, at 110 celsius grade, M16X1,5

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
ginko
  • 19396 Answers

SOURCE: Engine coolant temperature is lower than thermostat

This happens when the Engine Coolant Temperature (ECT) does not reach 75°C (167°F) despite sufficient engine warm-up time.

This happens usually when the thermostat/temperature sensor is faulty, and is bad for emissions and fuel consumption.

The repair cost may vary, even if themperature sensor is not an expensive part, after replacing the sensor there is need to reset the ECU (car computer module).

Posted on Dec 13, 2008

Ad
emissionwiz
  • 76673 Answers

SOURCE: I get a DTC P0133 code on my 1998 Ford Explorer V8

it may be a defective O2 sensor here is th difinition:
P0133 - Heated Oxygen Sensor (HO2S) Slow Response Bank 1 Sensor 1 , this is the sensor on the side of the engine that #1 cylinder is on, it is the sensor before the cat.

Posted on Jan 14, 2009

  • 521 Answers

SOURCE: Coolant Temperature Sensor location on 2006 impala

driver side of the engine block, forward and above the transmission. This piece threads into the engine block.

Posted on Jul 22, 2009

  • 169 Answers

SOURCE: sensor locations

air intake look at snorkel it could be part of mass air flow check intake for eng coolant

Posted on Aug 29, 2009

  • 1149 Answers

SOURCE: It needs a coolant temperature sensor. Where is it

Hi:
The coolant temp sensor is very close to where the upper radiator hose enters the top of the engine.

Posted on Dec 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have 2008 PT Cruiser; getting P0128 code; I've changed thermostat & temperature sensor; I have to fill the anti-freeze container every 2 weeks; temperature hand will not always be at half way point. ...


This means that the engine's PCM detected that the engine has not reached the required temperature level within a specified amount of time after starting the engine. The intent of the P0128 code is to indicate a faulty thermostat. In determining the engine did not reach a "normal" temperature, it takes into account the length of time the vehicle has been running, the intake air temperature (IAT) sensor reading, the engine coolant temperature (ECT) sensor reading, and the speed of the vehicle.
A code P0128 may mean that one or more of the following has happened:
  • Low engine coolant level
  • Leaking or stuck open thermostat
  • Faulty cooling fan (running too much)
  • Faulty coolant temperature (ECT) sensor
  • Faulty intake air temperature (IAT) sensor
Past experience indicates that the most likely solution is to replace the thermostat. However here are some suggestions on troubleshooting and repairing a P0128 OBD-II code:
  • Verify coolant strength & level
  • Verify proper cooling fan operation (check if it's running more than it should). Replace if necessary.
  • Verify proper engine coolant temperature (ECT) sensor operation, replace if necessary.
  • Verify proper intake air temperature (IAT) sensor operation, replace if necessary.
  • If the above items check out good, replace the thermostat
you have all ready replaced the thermostat with the proper temperature opening thermostat(hopefully) and coolant sensor, you say you have to refill the coolant every 2 weeks this indicates that you either have a coolant leak that needs to be checked out and repaired or you are burning coolant which indicates a possible head gasket problem which will have to be checked. a low coolant level will set this code as there is not enough coolant in the engine to get the engine to operating temperature and stay there. these last suggestions is where I would start to look.

Sep 24, 2014 | 2008 Chrysler Pt Cruiser

1 Answer

89 dodge ram truck 2500 2wd code reader says 4 codes dont know what they mean p1509, p1298, p0118 andp0113


P1509 Dodge - Leak Detection Pump Switch or Mechanical Fault

P1298 Dodge - Air/Fuel Ratio Lean Under Wide Open Throttle Condition
- Plugged air filter
- Plugged fuel filter
- Defective fuel pump
- Ignition system weak-misfires
- Defective coil

P0118 Dodge - Engine Coolant Temperature Sensor Circuit High
- Low engine coolant level
- Faulty Engine Coolant Temperature (ECT) sensor
- Faulty engine coolant thermostat
- Engine Coolant Temperature (ECT) sensor harness is open or shorted
- Engine Coolant Temperature (ECT) sensor electrical circuit poor connection

P0113 Dodge - Intake Air Temperature Sensor 1 Circuit High
- Faulty Intake Air Temperature (IAT) sensor
- Dirty air filter
- Intake Air Temperature (IAT) sensor harness is open or shorted
- Intake Air Temperature (IAT) sensor circuit poor electrical connection

Dec 16, 2013 | Cars & Trucks

1 Answer

Overheating with AirCon ON, OK with Aircon OFF


if engine over heating coolant over flow jug will boil over you will see steam.sound like you have either faulty engine coolant temperature sensor or could have faulty fans relay or fuse or pcm problem if coolant fans dont turn on.have garage with code scanner that can do a snap shot on coolant temperature sensor check see how hot coolant temperature is see if coolant temperature over 220 degrees engine getting too hot.could have faulty water or blowed head gasket check engine oil on oil dip stick look milkly you have blowed head gasket. i use infra red laser thermometor check see how hot engine is over 107 celsius engine is overheating.

Dec 10, 2012 | 2000 Toyota Sienna

1 Answer

Code 1 senser P0118 on a 2004 V.W beetle dicesel


P0118 for Volkswagen - (ECT) Engine Colant Temperature Circuit High

Symptoms:- Engine Light ON (or Service Engine Soon Warning Light)

Possible causes:
(Inspect the following... Repair/Replace if necessary)
- Low engine coolant level
- Engine Coolant Temperature (ECT) sensor harness is open or shorted
- Engine Coolant Temperature (ECT) sensor electrical circuit poor connection
- Faulty Engine Coolant Temperature (ECT) sensor
- Faulty engine coolant thermostat

P0118 VOLKSWAGEN Description: The Engine Coolant Temperature (ECT) sensor is used to detect the engine coolant temperature. The sensor modifies a voltage signal from the Engine Control Module (ECM). The modified signal returns to the (ECM) as the engine coolant temperature input. The sensor uses a thermistor which is sensitive to the change in temperature. The electrical resistance of the thermistor decreases as temperature increases.
When is the code detected?:When an excessively high voltage from the sensor is sent to ECM.

I hope this helps! Let me know if you need further assistance.

Mar 08, 2012 | Mercedes-Benz C Cars & Trucks

3 Answers

P0118


As with all engine codes there is no one solution fits all, here is the info on the code from the diagnostic material.
P0118 - Engine Coolant Temperature Circuit High Input
Possible causes - Low engine coolant level
- Engine Coolant Temperature (ECT) sensor harness is open or shorted
- Engine Coolant Temperature (ECT) sensor electrical circuit poor connection
- Faulty Engine Coolant Temperature (ECT) sensor
- Faulty engine coolant thermostat P0118 Description The Engine Coolant Temperature (ECT) sensor is used to detect the engine coolant temperature. The sensor modifies a voltage signal from the Engine Control Module (ECM). The modified signal returns to the ECM as the engine coolant temperature input. The sensor uses a thermistor which is sensitive to the change in temperature. The electrical resistance of the thermistor decreases as temperature increases.

Feb 02, 2012 | 2005 Chevrolet Tahoe

2 Answers

What type of oil grade should i use in my 2001 audi 2.8 a4 quattro..this car came with no owners manual,and its time to change..thanks


Engine oil capacity with oil filter replacement = 6.0 litres.

Oil grade for 2001 Audi A4 Quattro 2.8
1. SAE 5W-30 / 5W-40, VW 502.00 - all temperatures.
2. SAE 10W-30 / 10W-40, VW 502.00 - all temperatures.
3. SAE 5W-50, VW 501.01 - all temperatures.
4. SAE 10W-50 / 10W-60, VW 501.01 - all temperatures.
5. SAE 5W-30 / 5W-40, VW 501.01 - bellow +15 Celsius degrees.
6. SAE 10W-30 / 10W-40, VW 501.01 - bellow +15 Celsius degrees.
7. SAE 15W-40 / 15W-50, VW 501.01 - above -15 Celsius degrees.
8. SAE 20W-40 / 20W-50, VW 501.01 - above -15 Celsius degrees.

LONGLIFE engine oil:
1. SAE 5W-30, VW 504.00 - all temperatures.
2. SAE 0W-30, VW 503.00 - all temperatures.


Please do rate my response. Thanks!

Jan 26, 2011 | 2001 Audi A4

1 Answer

My friends car came up with this code and p0117 and he says when he accelerates it feels like its holding back


The P0117 code would not effect the acceleration of the vehicle. Probably just need a good tune up unless there are other codes showing in the system.

P0117 - Engine Coolant Temperature Circuit Low Input. The engine coolant temperature sensor is used to detect the engine coolant temperature. The sensor modifies a voltage signal from the ECM. The modified signal returns to the ECM as the engine coolant temperature input. The sensor uses a thermistor which is sensitive to the change in temperature. The electrical resistance of the thermistor decreases as temperature increases.

Causes:
- Harness or connectors (The sensor circuit is open or shorted.)
- Engine coolant temperature sensor may be faulty
- Low engine coolant level.

Solutions:
- Replaced coolant temperature sensor
- Repair connector or harness

Jan 17, 2011 | Mitsubishi Eclipse Cars & Trucks

1 Answer

What type of engine oil does a Peugeot 306 (1.6 petrol engine) need?


Engine oil specifications for Peugeot 306 1.6 petrol engine:

1. SAE 5W-40, API SH or SG, for temperatures between -30 Celsius deg. and +40 Celsius deg.
2. SAE 10W-40, API SH or SG, for temperatures between -15 Celsius deg. and +40 Celsius deg.
3. SAE 15W-40, API SH or SG, for temperatures between -10 Celsius deg. and +40 Celsius deg.
4. SAE 15W-50, API SH or SG, for temperatures between -10 Celsius deg. and +50 Celsius deg.
5. SAE 20W-50, API SH or SG, for temperatures between -5 Celsius deg. and +50 Celsius deg.

Jan 02, 2011 | Peugeot 405 Cars & Trucks

3 Answers

What can keep causing Check engine code P0128


CODE P0128- THERMOSTAT MALFUNCTION. POSSIBLE CAUSES 1. ECT SENSOR IS OUT OF CALIBRATION. 2. CHECK THE OPERATION OF THE THERMOSTAT IT MAY BE STUCK OPEN.3.INSPECT FOR LOW COOLANT LEVEL OR FOR AN INCORRECT COOLANT MIXTURE.

Jan 06, 2010 | 2004 Kia Spectra

2 Answers

Location of the coolant temperature sensor


You will find this sensor where the fat hos comes from the radiator and conects to the engine block. It would be on the housing where the thermostat is located. If it is not there you should look for a sensor that has a wire connected to it anywhere on the engine block where a water inlet is located. I hope this helps. Don't forget to rate my answer, thanks.

Feb 13, 2009 | 2001 Hyundai Santa Fe

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...