Question about 1998 Ford Ranger SuperCab

1 Answer

Where is the check engine reset button located on a ford ranger 4x4 6 cyl automatic

Posted by on

  • pj81982
    pj81982 Nov 07, 2012

    Solution 1 helped turn off the check engine light however it didnt say where I can find the reset button

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 91 Answers

Disconnect battery for about 5min check engine should clear however if theres still a code it will appear about 10miles down the road

Posted on Nov 05, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
chrischronic
  • 235 Answers

SOURCE: Replace thermostat in 2000 ford ranger

the open pipe that you took the hose off of is the thermostat housing, you will need to remove this to reveal the thermostat, make sure you use a new gasket with sealant when reinstalling thermostat housing to prevent leaks and dont over tighten the bolts,run both bolts down as far as you can before final tightning

Posted on Dec 26, 2008

Ajkill
  • 2035 Answers

SOURCE: 2003 Ford Ranger/2.3 O2 sensor - How many and Where located ???

Engine Heated oxygen and catalyst monitor sensors—2.3L engine44e2701.jpg

Posted on Jan 16, 2009

junkman1249
  • 552 Answers

SOURCE: hi there,i need to get a copy of Ford Ranger 2007

check out rockauto.com

Posted on Mar 29, 2009

chuck943
  • 783 Answers

SOURCE: where is the ignition module control located on 1996 ranger 2.3 e

It does not have an ignition control module. The PCM (powertrain control module) fires the coil pack based on signal it recieves from the crankshaft position sensor and the camshaft position sensor.

Posted on Apr 08, 2009

  • 1348 Answers

SOURCE: 2002 ford ranger 3.0 is missing on 2 cyl plugs ok injectors ok new coilpack

do a compression test,as the intake manifold,like alot of fords is no good.

Posted on May 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of vaccum modulator valve on a 99 ford ranger


There isn't one , transmission is controlled electrically . If it doesn't shift right have it checked for DTC's - diagnostic trouble codes . Does the speedometer work ? VSS - vehicle speed sensor , input speed sensor .

Dec 21, 2016 | Ford Ranger Cars & Trucks

2 Answers

Need to reset ABS light on 1996 Ford Ranger


Maybe you have a bad speed sensor, its a shot in the dark but that sensor controls a lot of functions like the ABS, speedometer, check engine light can come on, automatics will shift hard or may not shift at all, o/d will flash. The video below shows a 1999 ford ranger automatic but if you check you might have the same sensor.

Feb 09, 2014 | 1996 Ford Ranger SuperCab

1 Answer

Where is the cam sensor located on 1995 ford ranger 4 cyl? Do you have a picture of what it looks like?


It is Under hood, center, upper engine area, front driver side of engine, mounted on cylinder head. And looks like this:



chuckster57_52.jpg

Jul 21, 2011 | 1995 Ford Ranger Supercab

2 Answers

Will a 87 ford ranger v6 4 wheel drive trans. fit in a 86 ford ranger 4 cyl 4 wheel drive


If automatic transmission wont work engine block's are not the same, if stander transmission you could swap out bell housing held on with four bolt's from one to the other. Good luck and hope this was very helpful.

May 19, 2010 | 1986 Ford Ranger 2WD

1 Answer

91 Ford Ranger XLT, 4 cyl, manual 5 spd. Engine


most likely right on top of steering colum around have way down

Oct 07, 2009 | 1992 Ford Taurus

1 Answer

1994 ford ranger 2.8 v6 engine automatic 4 wheel


That could Be caused by the TFI module Located on the side of the distributor its grey module that requires a special tool to remove the two screws

Aug 04, 2009 | 1984 Ford Ranger

1 Answer

1997 ford ranger cam shaft position sensor


If you have the 3.0 L or 4.0 L V6 engine, the cam position sensor is located on the top rear of the engine. If you have the 2.3 L 4 cyl. engine, you will find it on the left front of the engine behind the oil pump pulley.

Sep 27, 2008 | 1997 Ford Ranger SuperCab

1 Answer

91 Ford Ranger 4 cyl 5 speed. Can`t find clutch slave cyl. bleeder. Internal slave. Hard at times to get into 1st and rev. Also can`t find connector to hook up tester for check engine light on.


first the bleeder will be located on the cylinder that is mounted on the transmission to engine connection by the bell housing. Second the port for this is located along the drivers side under the hood either by the fire wall or along the top of wheel well it will be marked with a grey cap labled EEC.

Aug 28, 2008 | 1991 Ford Ranger Supercab

Not finding what you are looking for?
1998 Ford Ranger SuperCab Logo

178 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...