Question about Cars & Trucks

1 Answer

Anyone know which cylinder/ plug is the number two on a 1999 chevy blazer 4.3 6 cylinder?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Cars & Trucks Master
  • 550 Answers

Front of Engine
1 2
3 4
5 6
Back of Engine

Also the firing order of this engine is 1-6-5-4-3-2. I hope this was a help for you.Source(s):Haynes Repair Manual for the 1994-2004 Chevy S-10 and GMC Sonoma Pick-ups.

Posted on Nov 06, 2012

  • zach coriell Nov 06, 2012

    You re awesome. Something so easy but I couldn t track it down for the life of me. I really appreciate it. Your a good man

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

bryant329
  • 125 Answers

SOURCE: 1999 Chevy Blazer Starter

the starter is located on the passenger side lower motor. it has two bolts in it that hold it in place. it actually goes through a hole/slot in the transmission to the flex plate.

1st. disconnect the negative cable on the battery.
2nd. raise the vehicle safely and place a jack stand under the vehicle out of your way but near where you will be working(for safety).
3rd. remove the two bolts that hold the starter in place.
4th. remove the wires from the back of the starter.
5th. install in reverse order of above.

note: there may be little plates between the starter and the mounting points called shims. if there are then make sure you put them back.

Posted on Sep 24, 2008

davesmith_37
  • 94 Answers

SOURCE: cylinder 2 misfire on a 1998 chevy blazer

check your plug wires for tears and dont overlap them

Posted on Feb 27, 2009

  • 299 Answers

SOURCE: Chevy Blazer P0303 and P0420

Most probably and if a cat is not flowing proper is causes back preasure that can result in sticking or burned vavles,mechanic not nice by saying ignore the cat effiency code p0420.Can ussually have cat replaced at aftermarket muffler shop for approx. $200 cheaper than valve job or excessive fuel that you have used and damage that may occur to your engine.

Posted on Jun 16, 2009

  • 20 Answers

SOURCE: need to know which coil fires #2 cylinder

BUY A CHILTON BOOK FROM ANY CAR STORE.

Posted on Jul 22, 2009

  • 617 Answers

SOURCE: 1999 chevy blazer distributor cap diagram

need 8th digit of vin and engine size, email address to send diagrams to you

Posted on Feb 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need a spark plug firing order diagram for 1990 chevy s-10 blazer 4.3l


Firing order is 1-6-5-4-3-2. Cylinder numbers are, front to rear: left side (driver) 1,3,5, right side 2.4,6. Distributer numbers are: 1 in front side of cap. numbers run clockwise same as firing order from number one position.


gaker.jpg

Aug 03, 2011 | Chevrolet Chevy Cars & Trucks

1 Answer

I have a 99 chevy blazer will not start weve checked fuel pressure and spark at the plugs we checked the timing with a lite and its correct can u help


1999 Chevy Blazer 4.3L engine has an electronic EGR valve its in front of and below the intake manifold a cylinder looking part connected to a small wiring harness. It is bolted on with 2 10mm bolts alot of times a piece of carbon will get stuck in the pintle at the bottom of the EGR valve and will keep it open causing a large vacuum leak making it hard or impossible to start. Good luck.

Mar 10, 2011 | 1999 Chevrolet Blazer

3 Answers

Is there somewhere I can find a wiring diagram for a 1999 chevy blazer 4x4 that I can print off.


need a wiring diagram for a 1999 chevy blazer 4.3 4x4... had to replace motor and now the 4x4 wont work... anyone know where u can print off the diagram

May 02, 2010 | 1995 Chevrolet Blazer

1 Answer

Firing order for 1998 chevy blazer 4.3L motor the number 5 is miss firing


For the 1998 Chevy Blazer 4.3L V6:

Firing Order:
1-6-5-4-3-2

Cylinders:
......(back)......
|..6..|.......|..5..|
|..4..|.......|..3..|
|..2..|.......|..1..|
......(front)

Distributor Connections:
...........(back)
Coil-> o
6-----> o.......o <-----5
4-----> o.......o <-----1
2-----> o.......o <-----3
...........(front)

Let me now if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

Apr 15, 2010 | 1998 Chevrolet Blazer

2 Answers

Chevy Blazer P0303 and P0420


Most probably and if a cat is not flowing proper is causes back preasure that can result in sticking or burned vavles,mechanic not nice by saying ignore the cat effiency code p0420.Can ussually have cat replaced at aftermarket muffler shop for approx. $200 cheaper than valve job or excessive fuel that you have used and damage that may occur to your engine.

Jun 16, 2009 | 1999 Chevrolet Blazer

1 Answer

Firing order for 97 chevy blazer


Firing order is 1-6-5-4-3-2. Distributor cap should be numbered. Number one cylinder is front on driver's side (3 and 5 follow on same side). Number 2 is front on passenger's side (followed by 4 and 6).

Apr 29, 2009 | Chevrolet Blazer Cars & Trucks

3 Answers

4.3 L vortec firing orcer and wiring diagram


you need the firing order?? it is 1, 6, 5, 4, 3, 2 clockwise. Number one on cap is forward position, or 6 o'clock position, just left of the hold down bolt.

Jan 22, 2009 | 1995 Chevrolet Blazer

1 Answer

Dash Problems with my 2000 Chevy Blazer


Try checking the temperature sensor. I had alot of problems with my 2000 blazer, and found that a spark plug wire was arcing out the temp. sensor.

Oct 27, 2008 | 1999 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

177 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...