Question about 1996 Buick Century

1 Answer

I need to know where they are locatedhow to install ****** & motor mounts on a 1996 buick century

I need to know where the transmission mount and motor =mounts are located so i can replace them

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,101 Answers

The transmission mount is on the top of the transmission on the drivers side next to the battery,and one motor mount is under the motor on the passenger side next to the harmonic balancer. and the is either one or two mounts on top of the radiator to the front vavle cover

Posted on Nov 06, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3 Answers

SOURCE: replacement of the serpentine belt on 1997 buick lesaber how

Yes, I have a 97 buick and the motor mount does have to be removed. See information below that I retireved from Autozone.com:

REMOVAL & INSTALLATION
See Figures 7 through 13

  1. Disconnect the negative battery cable.
0900c152800b19a8.jpgFig. 7: Many vehicles have an accessory drive belt routing label affixed to the radiator shroud
  1. Remove the belt guard or coolant recovery reservoir as required.
  2. For 1996-99 supercharged engines, perform the following:
    1. Raise and safely support the vehicle.
    2. Remove the right-hand splash shield.
    3. Remove the connector from the crank sensor.
  3. For 1996-99 vehicles, remove the engine mounting bracket lower nut, stud and spacer. Carefully lower the vehicle.

Posted on Jan 28, 2009

SOURCE: motor and transmission mounts

Did you reconnect the shift link on the transmission?

Posted on Oct 02, 2008

emissionwiz
  • 75797 Answers

SOURCE: Need to replace tail light bulb on 1996 Buick Century

Inside the trunk, under the carpet behind the tail lights will be a whole bunch of small plastic nuts, running from one side of the car to the other. Take all of these plastic nuts off, and the whole tail light assembly will come off in one large piece. Find the bulb you need to replace, and reassemble

Posted on Apr 06, 2009

  • 272 Answers

SOURCE: Need to know roughly how long it would take to

Depends on your level of experience, quality of your tools and whether or not you have any frozen head bolts. The valve assembly and head come off as one unit on those. To clear the wires, emmision controls ect off of the top of the valve cover 30 minutes. remove valve cover 5 minutes (too scrape off excess gasket material. to remove exhaust manifold from side of head, (assuming no broken/stuck/stripped bolts 15 minutes with good hydraulic tools. To remove head (assuming all goes well and hydraulic tools, 15 minutes. To reassemble, double all times as surfaces need to be prepped and gaskets applied and proper torque on all bolts. It's an afternoon job if you ahve everything you need and nothing goes wrong. Typically add at least two or three hours of drilling and cursing to a head gasket replacement. and a trip for new drill bits and a tap (not beer) for the new hole you drilled.

Posted on May 13, 2009

  • 1 Answer

SOURCE: motor mounts and pulley tensioner

I was wondering how do you take off the front transmission mount on a 1997 buick park avenue

Posted on Jul 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can i locate the motor mounts for 2002 buick century


Jack the car up and support it on safety stands crawl under the car and you will see them under the engine and one under the transmission and one side mount.

Feb 23, 2017 | Buick Cars & Trucks

1 Answer

How to replace motor mounts on 1991 buick century 3.3 v6


if you have the proper tools you will need to support the engine with a jack, undo the mount nuts and bolts remove them then remove the mount. you can use the jack to move the motor up or down depending on what needs to be done.

Apr 11, 2015 | 1991 Buick Century

1 Answer

How to remove engine


disconnect all electrical wiring harness that is attached to motor, disconnect exhaust, disconnect intake hoses, drain cooling system remove radiator, undo motor mounts, disconnect transmission, disconnect auto trans flex plate and attach engine crane remove engine replace torque converter and solenoids and reinstall or disconnect electrical from transmission and cooler lines and driveshaft and support trans with jack and undo cross member and drop transmission out of vehicle with jack supporting it and then rebuild transmission

Aug 07, 2014 | 1996 Buick Century

1 Answer

Replacing motor mounts on a 2003 buick century


How do I replace the motor mounts on a 2003 Buick Century.And how many is there on the motor and transmission.And where are they located at I know there are to on top and are there to on the side of the motor as well.Well thank you for your time.

Jun 13, 2012 | 2003 Buick Century

1 Answer

What does that mean when my 1993 buick century jerks.. when i stop at a light then go it jerks


Your transmission is most likely slipping, you can get anti slip fluid at your local parts store, be sure not to overfill, you may be low on transmission fluid check the level. If this does'nt help there could be significant damage to the transmission. Motor mounts can have the same affect you can have your local mechanic inspect them. Usually a mechanic will check the motor mounts for little or no charge.

Mar 20, 2011 | 1993 Buick Century

1 Answer

How do I replace the fan blower?


GM Celebrity/Century/Ciera/6000 1982-1996 Repair Guide

Blower Motor - REMOVAL & INSTALLATION

This procedure is applicable for vehicles, with or without air conditioning.
  1. Disconnect the negative cable at the battery.
  2. On the 3.1L (VIN M) you will need to remove the serpentine belt and move the alternator aside.
  3. For the 2.2L (VIN 4), disconnect the air inlet resonator, then remove the torque strut from the engine. Rotate the engine slightly forward.
  4. Working inside the engine compartment, disconnect the blower motor electrical leads.
  5. Remove the motor retaining bolts. If there is a hose disconnect it, then remove the blower motor.
To install:
  1. Position the blower motor on it's mount.
  2. Install the mounting bolts and tighten until snug.
  3. Attach the drain hose if removed, then engage the electrical connection to the motor.
  4. On the 2.2L (VIN 4), properly position the engine and install the torque strut to the engine. Connect the air inlet resonator.
  5. On the 3.1L (VIN M), install the alternator, if removed. Install the serpentine belt.
  6. Connect the negative battery cable, tighten the cable bolt to 11 ft. lbs. (15 Nm).
  7. Reset the radio, clock and any other applicable electronic devices.

Hope helps (remember comment this)

Jul 15, 2010 | 1987 Buick Century

1 Answer

Can I change the shift solenoid 1-2 (code P0753) 1997 Buick Century. Where is it located?


The shift solinoids are mounted to the valve body which is behind the side cover of the transmission. Usually you have to lower the trans to remove the side cover, which envolves lowering the subframe. If you drop the subframe the steering rack must be disconnected and the engine must be held from above because most of the motor/trans mounts are on the subframe

Jan 10, 2010 | 1997 Buick Century

1 Answer

Replace the engine motor mounts and the transmission mount. Would like to know how to do it. Thanks.


Check the frame mounts too. You will have to loosen the bolts and jack the motor up with a jack and a woodblock.

May 04, 2009 | 1996 Chrysler Concorde

4 Answers

Motor mounts and pulley tensioner


that car to my knowlege & replacemt has one engine mount by the belt & 2 tranny mounts one in the front & that canbe purchased at amazon for about $130 alot cheaper then dealer! also rear tranny can be purchase as insert or complete with bracket & mount together! have no clue on tensioner as mine has not went yet!!

Jan 22, 2009 | 1997 Buick Park Avenue

1 Answer

96 buick century makes thumping noise when higher rpm is reached


Sounds like a classic motor mount problem. Might want to get the dogbone strut checked as well.

Sep 27, 2008 | 1996 Buick Century

Not finding what you are looking for?
1996 Buick Century Logo

425 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...