Question about 2001 Ford Taurus

1 Answer

Ignition swicth - 2001 Ford Taurus

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 14,223 Answers

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Turn key car starts fine turn key to shut car off and it dont shut off


that could be the ignition swicth when you turn the key to take it out its like a kill swicth to spot the spark plugs working. you might need a new barrel look for the key. just I think.

Launch X431 tools

Sep 27, 2013 | Mercury Grand Marquis Cars & Trucks

1 Answer

2001 catera key works hard now when i turn it i get nothing,no dash lights and wont turn over. i think its my ignition lock or ignition swicth any suggestions


GM has a known problem with their Ignition Switches, Ignition Cylinders.... That is where I would start. The Hard Turning tells me that it was an internal failure

Apr 06, 2013 | 1998 Cadillac Catera

1 Answer

Key switch on 1998 taurus


I would look for a direct short in your wiring harness. It sounds to me like the wires are shorted together under your dash or maybe even out by your starter. Look for a location that contains the ignition wires and the starting circut.

Nov 12, 2011 | 1998 Ford Taurus

1 Answer

How to reset the light on of fuel filter in th eodometer for the toyota land cruiser 2010


the first thing you do is to replace the fuel filter then disconnect the clogged sensor. a) turn the ignition swicth ON POSITION...b) after turning the ignition swich on,connect the clogging sensor connector within 3 to 60 seconds. c) check that the combinition meter's filter warning light turns off.

Aug 04, 2011 | 2007 Toyota Land Cruiser

1 Answer

I have a 2005 grand marquis the wipers blades come on themself while driving the swicth is off


disconnect battery first, then with the key in the ignition, using a paper clip or something the same size put it in tiny hole on bottom of switch pushing up and turn key counter clockwise should allow the ignition lock cylinder to come out.

Apr 24, 2011 | 2005 Mercury Grand Marquis

1 Answer

Car wouldnt start ooutta nowhere,, would have to push key in harder b4 wouldnt start finally... help feel like i am paying too much san antionio tx


the first thing to do is to use penrating oil to lubricate the key barrel if the please replace the ignition swicth assemble,remove the steering column cover by a metal screw then remove the cover and remove the screw from the cylinder barrel remove the ignition swicth assemble then replace with a new one

Mar 17, 2011 | 1996 Oldsmobile 88

1 Answer

HOW DO I INSTALL A IGNITION OR STARTER KILL SWITCH ON A 1996 HONDA PRELUDE. ITS BEEN STOLEN ONCE.


i would put a tago swicth on my positive wire on the coil pack and just install the swicth inside somewere.that is what i did

Apr 10, 2010 | 1997 Honda Prelude

1 Answer

How to install a ignition swicth for 89 mustang gt


try moveing your stearnwheel back and forth and trun the key at the same time. but i hate to tell you will have to re place the switch. some time down the road have a nice day

Mar 26, 2009 | 1989 Ford Mustang

1 Answer

1997 sable changed radio and fuses clock and radio still doesn't work whatelse could it be


You need to identify the cable that feeds electricity to the radio when the ignition swicth is in the ON possition, and then identify the stanby power cable ( this is the cable that always has current even with the swicth on OFF possition) The Stanby cable goes to the cable marcked memory on your new radio. the other cable simply goes to the power suply conection on the new radio.

Aug 29, 2008 | Mercury Sable Cars & Trucks

Not finding what you are looking for?
2001 Ford Taurus Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...