Question about Cars & Trucks

Open Question

Bleeding cooling sistem in a John Deere 445 k series garden tractor

Does not use any coolant. Goes into the red for a short while and back again.

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1118 Answers

SOURCE: 98 sedan deville how to bleed cooling sistem

There should be bleeder valves either on the thermostat housing or by waterpump, just loosen them up start car and let it come up to temp. or until cooling fans come on, and watch them, when all air bubbles are gone and just coolant comming out, just close them back up and thats it. Now if there is no bleeders, just leave radiator cap loose on first notch and do same procedure stay back as it can be messey, when it looks like its all burped out shut off car let cool down and top off radiator and that should be it. Just watch your temp. guage as you do this as you don't want it to get real hot.

Posted on Mar 02, 2009

Ad
wireguy212
  • 1627 Answers

SOURCE: taking lawn mower off john deere 455 tractor

Undo the lever in the front by pulling it out and then rolling it downward to release the front of the deck [lower it to the ground before you start].Once that bracket is off you need to remove the drive shaft by pulling back on the lock collar on the shaft and then pull off the pto shaft.Now pick up the rear of the deck slightly and pull out the c hangers in the rearof the deck just ahead of the back wheels.Jack up the left rear end to make it easier to pull the deck out from under the tractor.

Posted on Nov 19, 2009

buluone
  • 40 Answers

SOURCE: Where can I find a freeze plug for an old 850 John

Assuming you've check with a dealer, the next step is to take the old plug to a quality auto parts store to match by size. If you don't have the old plug, take an accurate measurement of the hole to the store, they can match by size.

Posted on Jun 09, 2010

emissionwiz
  • 76848 Answers

SOURCE: I have a John Deere 3720 ran over a small branch wich disconcted 3 small wires underneth my tractor. Now I have no forward hydrostat it has been in the john deere dealer for 2 weeks they can not figur

You may have this posted in the wrong product category. Please select another category appropriate to the problem and re-post the problem so the correct expert will see and respond to the question..

Posted on Aug 29, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Y dose the john dear 6330 run hot all the time even after it blowen out



Engine or hydraulic system overheating clearpix.gif clearpix.gif clearpix.gif clearpix.gif clearpix.gif clearpix.gif Coolant system low on coolant in 6020, 6030, 6030 Premium, 7020, 7030 and
7030 Premium Series Tractors.

]clearpix.gif//-->
Symptoms
After several hours of work, warning system indicates hot engine coolant or hot hydraulic oil.
Situation or Problem
Coolant level in reservoir is between the "MIN" and "MAX" range but engine or hydraulic system is overheating.
Summary
Air is entering cooling system, hindering coolant flow. Check coolant level. Fill to the "MAX" line on the coolant reservoir.
Bleeding Cooling System:
The bleed valve (see Operator's Manual for location) on the radiator must be closed when the tractor is operating. Open the valve when coolant is drained or filled. If the bleed valve is left open, coolant will internally bypass between the low temperature circuit and engine high temperature circuit causing overheating. When bleeding the system, open the bleed valve and run the engine with no load for 5 minutes at 1700 rpm. Then shut engine off for 5 to 10 minutes before closing the drain valve. Check the coolant level. If level is below the "MAX" fill line, repeat this procedure until coolant level stays at the "MAX" line.

May 21, 2014 | Cars & Trucks

1 Answer

Coolant temperature gauge goes up down


Did you bleed the air from the cooling system?

Mar 10, 2014 | Ford Expedition Cars & Trucks

1 Answer

2006 chevy cobalt the engine cooling fan is not coming on


Check with warm engine and off by touching on your radiator vents whether is in all places same temperature. If not check whether you have air in the coolant which needs bleeding,or not good coolant circulation,caused either by clogged radiator,not good water pump,or faulty thermostat.By having these things it is the possibility the fan switch not getting the correct temperature to allow the fans to start. the last thing if everything is working,the possible is the fan switch itself.

Sep 02, 2012 | 2006 Chevrolet Cobalt

1 Answer

My chevrolent impal coolant goes to the red


on new cars you have to make sure you are using orange coolant, cause the green is killer.it start to eat away at the components and mayor problems will come so have the sistem check and flush.

Jul 02, 2012 | 2003 Chevrolet Impala

1 Answer

Location of coolant drain plug on side of motor for a 1995 mitsubishi montero


Not exactly,need to bleed air from system look topside of engine area for a bleeder port may need a filler reservoir full of coolant when doing this keep it full turn on heater full hot fan on high watch temp gauge if it gets hotter than normal reading and no hot air from heater ducts turn engine off ASAP it can be a pain in the grommet to bleed cooling systems but if you don't engine damage is imminent got to get air out of system drain plug on block does not sound right maybe it's on the top of block I have pulled hoses and filled system thru those and even used garden hose to force air out squeeze hoses rock vehicle and make big messes but don't overheat the engine from complete cool engine you have about ten minutes to get r done then let it cool down try again

Apr 02, 2012 | Cars & Trucks

2 Answers

Does the engine need to be running on my 02 Montana to bleed the air from the cooling system?


yes it does, most engine need to be running as to circulate the coolant so all the air is out of coolant system when bleeding.

Sep 20, 2010 | 2002 Pontiac Montana

1 Answer

My 2004 elantra overheated, the radiator cracked, so i replaced the radiator, and upper and lower hoses. now it over heated again...no leaks. Advise from friend is to replace thermostat... needing insights...


did you check the cooling fan its work ? did you bleed the colling sistem & to add a new antifreeze maybe you have a problem in the temp sensor o wires of the sistem

Jul 16, 2009 | 2004 Hyundai Elantra

1 Answer

98 sedan deville how to bleed cooling sistem


There should be bleeder valves either on the thermostat housing or by waterpump, just loosen them up start car and let it come up to temp. or until cooling fans come on, and watch them, when all air bubbles are gone and just coolant comming out, just close them back up and thats it. Now if there is no bleeders, just leave radiator cap loose on first notch and do same procedure stay back as it can be messey, when it looks like its all burped out shut off car let cool down and top off radiator and that should be it. Just watch your temp. guage as you do this as you don't want it to get real hot.

Mar 02, 2009 | 2001 Cadillac DeVille

1 Answer

I installed a new master cylinder and booster on my 76 B100 Dodge Van and the brake pedal goes to the floor and does not come up on its own. After I pull it up manually, it stays up but when I push it down...


Hi you need to bleed this sistem realy good ,if you dont have the lines to bleed it ,you can have some one to assist you by pumping the brake and holding it down while you losen the lines and tigten them again ,continue doing this until the pedal returns by itself.

Aug 24, 2008 | 1994 Dodge B Series Cargo

2 Answers

Flashing coolant temperature red light


Hi, vws are very tricky when it comes to cooling sistem,they never get completly full of antefrezze and they need to be bleed in order to work properly , you can disconect the uper radiator hose to fill the sistem ,you must wait for the air to come out,be patient .good luck

Aug 18, 2008 | 1990 Volkswagen Cabriolet

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...