Question about 2003 Mazda Mazda6

Open Question

P0335 crankshaft position sensor of mazda 6 - 2003 Mazda Mazda6

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 184 Answers

SOURCE: P0335

Hi, you can fix it by reading the article found here on P0335 - http://www.obd-codes.com/p0335

Posted on Feb 09, 2010

  • 38 Answers

SOURCE: replace crankshaft position sensor

Go to your local auto parts store and by a manual. It will tell you where it is.

Posted on May 20, 2010

  • 1 Answer

SOURCE: Crankshaft position sensor

solution #2 was right. The comment was not. It is inside the distributor. Some engines as stated in solution #1 are one the engine block but not this engine, it is in the distributor.

Posted on Jun 09, 2010

leedavidian
  • 1420 Answers

SOURCE: how to replace the crankshaft

Welcome to FIxYa.com


CRANKSHAFT POSITION - SENSOR REPLACEMENT


1. Disconnect the negative battery cable.

2. Remove the idler pulley bracket.

3. Remove the dipstick pipe.

4. Remove the CKP sensor

5. Install in the reverse order of removal.

6. Adjust the drive belt deflection.

leedavidian_52.png


Thank you for using FixYa.com

Regards, Lee Davidian

Posted on Nov 09, 2010

  • 107 Answers

SOURCE: Hi my 2001 mazda mpv

After I visited the website named "MPVclub.com," I read an article there that shows the crank position sensor to be located on the right side of the motor buy the crank pulley. You can't miss it, it is right in between the crank pulley and the a/c compressor. Go to www.MPVclub.com, then go to forums, which is on the left hand side of the page, go to 00-06 MPVproblems, go to page 2 and go to the bottom of the page to "PO335 Crankshaft position sensor Replacement, you will see the comments and some pics that will guide you to it.
Hope this helps.

Posted on Feb 10, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the 2nd crank shaft sensor located, and is there a diagram to show where these sensors are located?


is it a no crank or crank no start?
Possible causes for code P0335
- Faulty crankshaft position sensor
- Crankshaft position sensor harness is open or shorted
- Crankshaft position sensor circuit poor electrical connection
- Signal plate may be damage
- Starter motor may be faulty
- Starting system circuit
- Dead or weak battery

Read more: http://engine-codes.com/p0335.html#ixzz3Cxw6SN6O

Sep 10, 2014 | 2004 Buick Rendezvous

1 Answer

2005 Dodge Neon SXT 2.0L crankshaft position sensor location to replace


P0315 - Crankshaft Position System Variation Not Learned
P0335 - Magnetic Crankshaft Position Sensor Electrical Error China OBD2 car diagnostic tools wholesale on CareUCar

Mar 20, 2014 | 2005 Dodge Neon SXT

1 Answer

Got an error code P0335 on a 2005 Nissan Sentra 1.8L, what is wrong with it? How can I fix it?


code p0335 refers to crankshaft position sensor ( CKP)-circuit malfunction === causes --wiring---CKP sensor---ECM Replace the sensor.

Sep 28, 2013 | 2003 Mazda Mazda6

1 Answer

Engine management light on trouble code P0335


P0335 - Crankshaft Position Sensor 'A' Circuit Malfunction

Possible causes- Faulty crankshaft position sensor (most common)
- Crankshaft position sensor harness is open or shorted
- Crankshaft position sensor circuit poor electrical connection
- Signal plate may be damage
- Starter motor may be faulty
- Starting system circuit
- Dead or weak battery causing slow engine crank over.

Oct 25, 2012 | 2005 Fiat Punto

1 Answer

Replaced camshaft and crankshaft position sensors in my 2005 altima also the o2 seneor car still will not run. error code 335 What else could be the problem?


DTC P0335 - Crankshaft Position Sensor A Circuit Malfunction
The crankshaft position sensor (CKP) measures crankshaft location and relays this information to the PCM (Powertrain Control Module). Depending on the vehicle, the PCM uses this crankshaft position information to time the spark properly or on some systems it is only for misfire detection and does not control spark timing. The CKP sensor is stationary and works in harmony with a reluctor ring (or toothed ring) that is attached to the crankshaft. As this reluctor ring passes in front of the CKP sensor, the magnetic field created by the CKP sensor is interrupted and this creates a square wave voltage signal that the PCM interprets as crankshaft position. If the PCM detects that there are no crankshaft pulses or if it sees a problem with the pulses on the output circuit, P0335 will set.

A P0335 "check engine light" code could be caused by:
Damaged CKP sensor connector
Damaged reluctor ring (missing teeth or not turning due to sheared-off keyway)
Sensor output open
Sensor output shorted to ground
Sensor output shorted to voltage
Failed crank sensor
Broken timing belt
Failed PCM

If you need additional details about test and solutions, just contact us in the Code Link.

Hope this helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer. Thank you for using Fixya, and have a nice day.

Jose.

Oct 21, 2011 | 2005 Nissan Altima

1 Answer

P0335 code,05 kia rio, changed crank sensor, did not help?


Did you do a crank relearn ? Could be a wiring issue , control module problem etc... Testing electrical circuit first , video's on youtube , all you would need is a DVOM - digital volt ohm meter . P0335 Kia Crankshaft Position Sensor Circuit c Replacing Crankshaft Position Sensor Code P0335

Jun 05, 2011 | 2005 Kia Rio

1 Answer

2001 Oldsmobile Aurora Codes P0302, P0335, P385, P0386


p0302 Misfire cylinder two

p0335 CKP Sensor 'A' Circuit Malfunction

p0385 Crankshaft Position (CKP) Sensor B Circuit

p0386 Crankshaft Position Sensor B Circuit Range/Performance

Make sure your crankshaft sensor is plugged in or replace the sensor if the plug is good.

Jun 05, 2011 | 2001 Oldsmobile Aurora

1 Answer

My problem with my JEEP Liberty 2004 is p0335


Diagnostic Trouble Code (DTC) P0335

Magnetic Crankshaft Position Sensor Electrical Error



In this circuit DTC (data trouble code) sets when


a) The magnetic crankshaft position sensor is > 0.2V.

Or when


b) The minimum value of magnetic crankshaft position sensor is

Or when

c) The maximum value of magnetic crankshaft position sensor is higher than 2.2V.

Feb 18, 2011 | 2004 Jeep Liberty

2 Answers

Crankshaft Position Sensor Error P0335 recurred after r&r


In the kit there are two sensor that look identical. The one for the crankshaft has a white paint mark on it near the bolt hole. Make sure that it is in the right location.

Jul 25, 2009 | 2003 Nissan Altima

1 Answer

P0335


Hi, you can fix it by reading the article found here on P0335 - http://www.obd-codes.com/p0335

Mar 29, 2009 | 2003 Mazda Mazda6

Not finding what you are looking for?
2003 Mazda Mazda6 Logo

Related Topics:

407 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...