Question about Cars & Trucks

Open Question

What is the torque pressure on head bolt for a ford laser kj2 1.6 engine

Ford laser KJ2 1997 hatch back 1.6 Engine. Engine : B6593...

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
oldfishead
  • 155 Answers

SOURCE: what should i torque the head bolts to on a 2001

for a 3.0 2v....new head

    1. Install the bolts.
    2. Tighten the bolts in five stages in the sequence shown.
    • Stage 1: Tighten to 50 Nm (37 lb-ft).
    • Stage 2: Loosen the bolts one full turn.
    • Stage 3: Tighten to 30 Nm (22 lb-ft).
    • Stage 4: Rotate each bolt 90 degrees.
    • Stage 5: Rotate each bolt an additional 90 degrees.
  • intake bolts are:
    1. Install the intake manifold. Tighten the bolts in the sequence shown in two stages.
    2. Stage 1: Tighten to 15 Nm (11 lb-ft).
    • Stage 2: Tighten to 32 Nm (24 lb-ft).
    • work from the center out
  • Posted on Jul 07, 2009

    Ad
    johnjohn2
    • 5763 Answers

    SOURCE: 93 ford aerostar 4.o engine head bolt torque

    step one is 22 ft lbs.
    step two is 52 ft lbs
    step #3 is turn an additional 90 degrees. sart in the middle and work your way out going top tobottom, good luck.

    Posted on Nov 03, 2009

    Testimonial: "thanks very much. I thought that the "90 degrees" on the gasket instruction sheet was a misprint. Your answer was quick and informative. G.M."

    • 432 Answers

    SOURCE: engine torque specifications ford escape

    Bolts are torque to yield and new ones are recommended.
    Stage 1 15ft lbs
    Stage 2 30ft lbs
    stage 3 additional 90 degrees

    Posted on Jul 25, 2010

    • 501 Answers

    SOURCE: what is the torque pressure

    60psi

    Posted on Dec 10, 2010

    Testimonial: "Very helpful thank you."

    • 1608 Answers

    SOURCE: what is the torque pressure on cylinder head bolts

    The torque specs for the head bolts are 51 ft.lbs.then an additional 90-100 degrees(angle).Hope this helps.Good luck.

    Posted on Dec 10, 2010

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    Can I use 10w 30 in my ford laser gl hatch?


    if the weather is below 15 Celsius and the engine is low mileage them it will not be a problem

    Mar 09, 2015 | Ford Cars & Trucks

    1 Answer

    I have a ford laser hatch back 1994 model and i need a code for the stereo pls


    When you disconnect your battery and then reconnect it again, it disables the radio. This is an anti-theft protection for your car radio.
    The enable your radio the activation code is in your vehicle owner's manual. If you do not have this code you need to go to your Ford service centre and get them to enter this code for you.

    Jan 07, 2013 | 2000 Ford Focus

    1 Answer

    Rear hatch door in ford windstar-mechanism came apart


    My back hatch would not open but it appears the lock was sticking and the return spring to the handle is broken. We used the key to unlock the back door and then door opened. Then husband sprayed WD 40 in all the lock holes. Now once we open the door we have to push the handle back down as return spring is still missing but the door opens :) . My van is a 2002 Ford Windstar.

    Jan 29, 2012 | 2001 Ford Windstar

    1 Answer

    My Ford Escape 2001's back hatch door cannot be locked


    I had the same problem on my 2002 Escape. Ended up taking it to the dealer and they replaced the Lift Gate Lock Actuator - cost us about $310 (parts and labor). Part #1C3F-18C815-AB

    Mar 10, 2010 | 2002 Ford Escape

    1 Answer

    Hello i have a 1988 ford escort GL hatch back and it is clearly shuting gas into the intake and it is still not starting i think its the spark but im not sure


    Remove a spark plug wire, insert a phillips screwdriver in the wire and set it near a ground where there is a small gap like 1 inch or less between the screwdriver and the block or a ground to the frame, have someone crank the engine and see if you hear or see a spark

    Mar 01, 2010 | 1988 Ford Escort EXP

    1 Answer

    Dome lights stay on after car is started


    Check the rear hatch switches, My ford winstar did the same thing. I had ford fix it the 1st time, trouble came back, took panel apart myself, I found 2 switches 1 on each side of the hatch. I Isolated to one, and the other didn't do anything so I switched them around and trouble never came back.

    Jul 28, 2009 | 2004 Dodge Durango

    1 Answer

    Have 2001 Ford Windstar. Had back hatch open and backing down drive way. Corner of hatch hit edge of the house. The hatch was pushed up & in aprox. 2" so it now hangs at a slight angle and won't close. ...


    makes me wonder if it is just the hinge that is bent and maybe the body where it attaches to the van. At the same time I doubt some thing easy will do away with the $2k expense (sorry). Maybe an entire back hatch with hinges from salvage yard (make sure to get same color).

    Feb 23, 2009 | 2001 Ford Windstar

    1 Answer

    2002 Ford Explorer Limited rear hatch body piece broken


    look for one at a salvage yard or someplace that sells after market parts just ask for a rear door hatch exterior panel

    Jan 08, 2009 | 2002 Ford Explorer

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    99 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    yadayada
    yadayada

    Level 3 Expert

    77186 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22265 Answers

    Randy Ohler

    Level 3 Expert

    14585 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...