Question about 1999 Honda Accord

1 Answer

No high tension power out on sprak plug

H22 engine w/ two sensor crank and cam front of the crank shaft

Posted by on

  • Anonymous Mar 21, 2014

    what is the crank shaft sensor

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Master
  • 1,007 Answers

Check crankshaft and camshaft position sensors.

Use an scanner to read any ECU trouble codes.

Posted on Nov 05, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why my 97' f-250 7.3 powerr stroke keeps dieing while idling


The power stroke engine has several things that will cause this problem #1 crank shaft sensor AKA cam shaft sensor on crank shaft located on passenger side of engine near crank shaft pulley # 2 IPC sensor Injection pressure control if has oil in sensor replace it & wiring pigtail .#3 high pressure oil pump not up to par. #4 injection pressure regulator solenoid they get sticky. with a good scanner that has FORD enhanced software you can check all of these without leaving the drivers seat and perform running tests on injectors and test the ficm module interface with the pcm. Fuel Injection Control Module & Power Control Module.

May 02, 2014 | Cars & Trucks

1 Answer

Car stall 1998 toyota corolla, replace cam shaft sensor, crank shaft sensor, could it be the main fuse box


The Year 1998 Toyota Corolla engine will stall due to:
Spark plug faulty
High-tension cord faulty
Ignition problems:
• Ignition coil
• Igniter
• Distributor
Incorrect ignition timing
Vacuum leaks:
• PCV line
• EGR line
• Intake manifold
Throttle body
• Brake booster line
Incorrect valve clearance
EFI system problems
Engine overheats
Low compression

Feb 11, 2014 | 1998 Toyota Corolla

1 Answer

If 3100 engine is running smooth could the cam shaft sensor be bad in a pontiac grand prix


Not CAM or Crank angle sensor.. Try check supply fuel line pressure n spark plug n ignition coil output.. the ignition coil output should be blue spark n spark jump at least half inch.. But be careful coz its hi tension..

Feb 01, 2013 | 1998 Pontiac Grand Prix

1 Answer

No power to crank position sensor?


The crank sensor gets power from the MFI relay just like the injectors and cam sensor do.

Jan 23, 2013 | 1998 Mitsubishi Eclipse

2 Answers

1997 dodge neon dose'nt get spark to the sprak plug why not


SCAN VECHICLE WITH CODE SCANNER FOR FAULTY CAMSHAFT SENSOR OR FAULTY CRANKSHAFT SENSOR. THEY WILL CAUSE NO SPARK PROBLEMS.

Dec 11, 2010 | 1997 Dodge Neon

2 Answers

05 kia amanti with diagnostics codes p0350,p0320,p0300,p0302,p0303,p0304,p0305,p0306.skipping at times.when it does skip & misfire the rpm gauge goes crazy.this problem is not consitant


Generic OBD II Diagnostic Trouble Codes

DTC CODES P0300 to P0399

P0300....Random/Multiple Cylinder Misfire Detected

P0301....Cylinder 1 Misfire Detected

P0302....Cylinder 2 Misfire Detected

P0303....Cylinder 3 Misfire Detected

P0304....Cylinder 4 Misfire Detected

P0305....Cylinder 5 Misfire Detected

P0306....Cylinder 6 Misfire Detected

P0307....Cylinder 7 Misfire Detected

P0308....Cylinder 8 Misfire Detected

P0309....Cylinder 9 Misfire Detected

P0310....Cylinder 10....Misfire Detected

P0311....Cylinder 11 Misfire Detected

P0312....Cylinder 12 Misfire Detected

P0313....Misfire Detected with Low Fuel

P0314....Single Cylinder Misfire (Cylinder not Specified)

P0320....Ignition/Distributor Engine Speed Input Circuit

P0321....Ignition/Distributor Engine Speed Input Circuit Range/Performance

P0322....Ignition/Distributor Engine Speed Input Circuit No Signal

P0323....Ignition/Distributor Engine Speed Input Circuit Intermittent

P0324....Knock Control System Error

P0325....Knock Sensor 1 Circuit (Bank 1 or Single Sensor)

P0326....Knock Sensor 1 Circuit Range/Performance (Bank 1 or Single Sensor)

P0327....Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)

P0328....Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)

P0329....Knock Sensor 1 Circuit Input Intermittent (Bank 1 or Single Sensor)

P0330....Knock Sensor 2 Circuit (Bank 2)

P0331....Knock Sensor 2 Circuit Range/Performance (Bank 2)

P0332....Knock Sensor 2 Circuit Low Input (Bank 2)

P0333....Knock Sensor 2 Circuit High Input (Bank 2)

P0334....Knock Sensor 2 Circuit Input Intermittent (Bank 2)

P0335....Crankshaft Position Sensor A Circuit

P0336....Crankshaft Position Sensor A Circuit Range/Performance

P0337....Crankshaft Position Sensor A Circuit Low Input

P0338....Crankshaft Position Sensor A Circuit High Input

P0339....Crankshaft Position Sensor A Circuit Intermittent

P0340....Camshaft Position Sensor 'A' Circuit (Bank 1 or Single Sensor)

P0341 Camshaft Position Sensor 'A' Circuit Range/Performance (Bank 1 or Single Sensor)

P0342....Camshaft Position Sensor 'A' Circuit Low Input (Bank 1 or Single Sensor)

P0343....Camshaft Position Sensor 'A' Circuit High Input (Bank 1 or Single Sensor)

P0344....Camshaft Position Sensor 'A' Circuit Intermittent (Bank 1 or Single Sensor)

P0345....Camshaft Position Sensor 'A' Circuit (Bank 2)

P0346....Camshaft Position Sensor 'A' Circuit Range/Performance (Bank 2)

P0347....Camshaft Position Sensor 'A' Circuit Low Input (Bank 2)

P0348....Camshaft Position Sensor 'A' Circuit High Input (Bank 2)

P0349....Camshaft Position Sensor 'A' Circuit Intermittent (Bank 2)

P0350....Ignition Coil Primary/Secondary Circuit

Nov 17, 2010 | Kia Amanti Cars & Trucks

1 Answer

How do u change the timing belt on a 1990 4 cylinder honda accord?


Disconnect the wire harness at the distributor.Remove the spark plug closest to the drivers side front tire. Place the palm of your hand over the valve covers empty spark plug hole and have a helper crank the motor over until air pressure pushes past your the palm of your hand. Next, look at the cam shaft wheel and note the direction that the arrow is pointing, the arrow should be pointing straight up IN RELATION TO THE ENGINE not the earth. If it is not, you will need to manually rotate the engine till the cam wheel is infact pointing straight up. Next, Jack up the front of the car and support it with jack stand and remove the front drivers side tire.Next, support the weight of the engine with a floor jack remove the motor mount closest to the drivers side tire To remove it you will need a deep 17mm socket on a heavy duty breaker bar. Next, loosen and remove the power steering belt and alternator belts. To loosen and remove the belts you will need a 10mm wrench and a 12mm wrench. And also a 14mm or 15mm wrench. Next, use a 19mm socket AND an air powered IMPACT wrench to remove the bolt holding on the crank shaft pulley. Next, remove the crankshaft pulley. Next, use a 10mm wrench and/or 10mm socket and remove the bolts holding the plastic engine side cover. Next, loosen the 14mm or 15mm bolt which secures the 2 belt tension wheels. Next, LOOSEN the 10mm bolt that is on the balance shaft tensioner. The balance shaft is the cogged wheel with a small timing mark dot on the side of the wheel. Next, loosen the 10mm bolt on the timing belt tensioner. It's obvious what wheel is the timing belt tensioner. Next, remove the 12mm bolt on the back side of the block (near the balance shaft) a little bit of oil will drip out, this 12mm bolt will allow a long bolt to be inserted into a recessed channel of the balance shaft. This recessed channel is needed to lock the balance shaft in place. A bolt from the air conditioner works great for locking the balance shaft in place. You're basically just pushing the bolt in a hole to keep the balance shaft from spinning.890a27a.jpg Next, remove both the balance shaft belt and timing belt. Then reverse the procedure to complete the new belt installation. EXTREMELY IMPORTANT!!!!!!!!! PLEASE NOTE, the oil pump wheel furthest to the left (closest to the radiator), has a timing mark on the flat face side of the wheel, that timing mark has to be pointing directly to the 9:o'clock position in relation to the engine. The cam wheel has an arrow on the side of one of the "spokes" ...make sure it is pointing straight up in relation to the engine...straight away from the crank shaft. Put the crank wheel on with the arrow pointing straight up to the center of the cam wheel.

Jun 28, 2010 | 1990 Honda Accord

2 Answers

Replacing a camshaft position sensor on a 1998 cutlass


The cam sensor is integrated with the crank shaft sensor behind the crank shaft pulley. The 3.1 runs 2 crank sensors. the one behind the crankshaft pulley in integrated to act as a cam sensor. It has 2 sets on rings for that sensor, 1 is in use accustomed for the fuel timing
Good luck and hope this helps friend. 

Jul 14, 2009 | 1998 Oldsmobile Cutlass

1 Answer

Hondai sonota


Which engine? 4 cylinder (2.4 lit) or V6 (2.7 lit)? Two different procedures as well as different belts. The 4 cylinder also has a balance belt. See next image:
42e8a57.jpg
Here's the 2.7 V6 belt:

44efb27.jpg
The replacement procedure is nearly the same at the start (removing, accy drive belts, pullys, support engine & remove front engine mount, remove T.B covers, disconnect Cam Position Sensor & Crank Position Sensor connectors, etc.). When you get to this point on the V6, you also have to remove the front engine mounting bracket from the front of the engine (4 14mm bolts, also a 12mm bolt which bolts the dipstick tube to the side of it) Put crank shaft at TDC (top dead center w/ALL timing marks aligned) remove hydraulic tensioner (2 12 mm bolts), then remove the belt. You'll need to recompress the hydraulic (auto) tensioner in a vise and insert a retaining pin through the pin-holes at the top (through the tensioner piston) to keep it compressed when you reinstall it. Otherwise, you won't be able to install it. Assembly is reverse order of dissassembly. Inspect your pullys while you're in there (check for pully bearing noise, leaking grease, smooth rotation, also the water pump pully, etc.) Replace components as needed. Careful not to damage Crankshaft Position Sensor wire harness.

The 4 Cylinder is quite different. You not only change the timing belt, but also the countershaft (balance) belt, which is behind the crank position sensor blade. IMPORTANT: ALL TIMING MARKS ALIGNED BEFORE REMOVING ANYTHING) There are two (2) counter-shafts (balance shafts). one driven by the timing belt, the other by the crankshaft sprocket behind the timing belt sprocket at the front of the crankshaft.
70f048d.jpg1999205.jpg366ecea.jpg b8013a3.jpg

Jun 02, 2009 | 2001 Hyundai Sonata

Not finding what you are looking for?
1999 Honda Accord Logo

Related Topics:

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...