Question about Cars & Trucks

1 Answer

Cant remove back hubs to put new shoes on hand brake

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 14,195 Answers

Hey Tommy,can you give me your vehicles info.,year,make ,model and year and I will send you the way.

Posted on Nov 05, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

losflip
  • 94 Answers

SOURCE: 2002 Hyunsai Accent rear brakes, do you have to remove wheel hub

Yes, it should be removed it makes the job a lot less difficuilt. 

Posted on Nov 30, 2008

  • 1 Answer

SOURCE: 1997 p reg ford escort

Not a solution per se but correction. 97 escort rear drum brakes do not use a STAR ADJUSTER. They use a "quadrant" adjuster attached to emergency brake cable I think. You'll see it coming out the back near top of backing plate. I don't think you can adjust them at all until drum is off. They are self adjusting once reinstalled.

Posted on Feb 02, 2009

martin538
  • 117 Answers

SOURCE: rear disc removal. Chrysler Grand Voyager

You need to de adjust the handbrake shoes through the small inspection cover on the back plates. Slackening off the parkbrake cable may help as well.

Posted on Apr 08, 2009

  • 3 Answers

SOURCE: Rear brake shoes VW lupo 1 ltr

open the brake drum , remove the pads and refit them , it's that simple . you don't need anything just to remove and refit them.

Posted on Sep 13, 2009

coupedeville
  • 97 Answers

SOURCE: removing rear wheel hub on hyundai getz 1.3

if you mean the drum then hit it in the front between the lugs should jar it loose. give it a good wack

Posted on Nov 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Remove rear brake drum 94 isuzu pickup


What is keeping it from coming off, does it move out but hang up?

Aug 25, 2016 | Isuzu Cars & Trucks

1 Answer

Removing and replacing rear brake shoes.


First you need the Van in the air either by hoist or by the jack provided to change the flats. Place blocks at the front wheels so Van doesn't roll when jacking the Van up. Remove each rear wheel and then remove the hub on one side revelling the brake shoes and then remove=e the brake shoes carefully remembering how they go so you can replace the old shoes with the new shoes the exact way, then you go to the other wheel and do the same ( the best is to remove the both hubs before you remove the shoes so that you can take them to the machine shop to have them turned ) put the hubs back on and then the wheels. While the Van is still jacked up you can ajust each wheel by turning it by hand and adjusting each wheel with the adjuster on the inner wheel . When the Van is jacked up brace the Van so it will not fall PS if the hubs are in bad shape and can't be turned you will need new ones .
Clean your tools before putting them away .

Jun 23, 2014 | 1994 Plymouth Voyager

1 Answer

Y cant i get my brake drums on after new brakes


Hi your need to make sure that they dit not given you a set off over size shoes. If it is standard shoes you need to make sure that the hand brake is going back all the way, and all so make sure that the hand brake adjuster is not the wrong way around. I hope it will help

Mar 20, 2013 | 2002 Suzuki Vitara

1 Answer

Brake shoes on 1987 f250 460 1987 2 wheel drive how to replace


Lift the front of your Ford F-250 off of the ground using a jack and jack stands. Remove the wheels from the Ford with a lug nut wrench to prepare the truck for servicing. 2 Open the hood on the engine compartment and take the lid off of the master cylinder that bolts to the brake assister on the driver's side firewall.3 Remove the hex-head bolts on the back of the brake caliper with a socket. With the bolts removed, pull the caliper off of the Ford's brake rotor.4 Pull the old brake pads out of the caliper and discard them. Squeeze the brake piston back into the backside brake caliper with pliers, and then insert the new pads into the brake caliper.5 Pull the rotor cap cover off the middle of the rotor with a screwdriver and use a socket to remove the nut located behind the cover.6 Pull the rotor off of the wheel spindle.7 Remove the old wheel bearings from the brake rotor and insert them into the new rotor. If the old wheel bearings are worn, replace them with new bearings.8 Slide the new rotor onto the wheel spindle and secure it using a bolt and socket. After you tighten the bolt, press the cover back onto the rotor.9 Place the caliper on the rotor and secure it with a socket and hex-head bolts. 10 Duplicate the process on the passenger side of the F-250. 11 Close the master cylinder after putting the wheels back on the Ford and lowering it to the ground. Press on the brake pedal to seat the pads against the rotor
Replace the F-250's Rear Brakes 1 lift the rear of the Ford F-250 off the ground with a jack and jack stands. Remove the wheels from the Ford with a lug nut wrench.2 Place a strip of paint on the back of the brake drum and rear brake drum cover so you can position the brake drum orrectly when you put it back on. If you plan to install new brake drums on your Ford F-250, skip this step. 3 Place the brake drum puller on the brake drum and pull the drum from the wheel hub. The method for attaching the brake drum puller depends on the brake drum puller that you use. 4 Remove the springs that attach the brake shoes to the wheel hub by pulling them off with pliers.5 Lift the old brake shoes off of the wheel hub and place the new brake shoes on the wheel hub. Secure the new shoes with the springs.6 Pound the brake drum onto the axle hub with a rubber mallet.7 Duplicate the process on the passenger side of the Ford.8 Put the wheels back on the F-250, lower it to the ground and, then press on the brake pedal to seat the shoes against the brake drum.

Oct 14, 2011 | 1988 Ford F 250

1 Answer

How do I get the rear spindle off so I can replace the emergency brake shoes on my 2006 chrysler pacifica?



Adjustment

  1. Place parking brake lever in -full released- position.
  2. Raise and support vehicle.
  3. Remove plug in parking brake shoe support to access adjuster star-wheel.
  4. Through the access hole, rotate the adjuster star wheel in the following direction to expand the shoes outward against the drum:
    1. Left brake - Rotate star-wheel toward rear of vehicle.
    2. Right brake - Rotate star-wheel toward front of vehicle.
  5. Using an appropriate tool, turn adjuster star wheel until wheel will not rotate (dead lock).
  6. Back off adjuster six detents (teeth).
  7. Rotate wheel, checking for light drag. If drag is too heavy, continue to back off adjuster one detent at a time until light drag is present. Do not back off star-wheel more than 17 detents from wheel lock.
  8. Install access plug.
  9. Adjust opposite wheel parking brake shoes using same method.
  10. Lower vehicle.
  11. Apply and release parking brake lever once to ensure proper operation of parking brakes.


Removal & Installation NOTE The following procedure may be used to remove shoes on either side of the vehicle.

  1. Lock out automatic adjuster in parking brake lever.
  2. Raise and support vehicle.
  3. Access and remove rear hub and bearing.
  4. Remove parking brake cable bolt at knuckle.
  5. Completely back off parking brake shoe adjustment.
  6. Remove parking brake shoe adjuster spring.
  7. Remove shoe adjuster.
  8. Remove upper brake shoe hold-down clip and pin.
  9. Remove lower brake shoe hold-down clip and pin.
  10. Remove upper and lower shoes with return spring from shoe actuator.
  11. Remove return spring from shoes.

    0996b43f80204c12.jpg

    Fig. View of the actuator (1), support (2), adjuster spring (3), return spring (4), caliper adapter (5), shoes (6), hold-down clips and pins (7) and adjuster (8)

To install:
  1. Install return spring between upper and lower shoes.
    NOTE Before installing shoes on actuator, make sure actuator hooked to rear cable is positioned with word -UP- facing outward.
  2. Install upper and lower shoes with return spring on shoe actuator located on parking brake cable.
  3. Install lower brake shoe hold-down pin through rear of support and lower shoe, then install hold-down clip.
  4. Install upper brake shoe hold-down pin through rear of support and upper shoe, then install hold-down clip.
  5. Install shoe adjuster. Place end of adjuster with star wheel upward.
  6. Install parking brake shoe adjuster spring.
  7. Install bolt securing parking brake cable to knuckle and tighten bolt to 21 ft. lbs. (28 Nm).
  8. Using Brake Shoe Gauge, Special Tool C-3919, or equivalent, measure inside diameter of parking brake drum portion of rotor.
  9. Place Gauge over parking brake shoes at widest point.
  10. Using adjuster star wheel, adjust parking brake shoes until linings on both park brake shoes just touch jaws on gauge. This will give a good preliminary adjustment of parking brake shoes, before a final adjustment is made at end of this procedure.
  11. Install hub and bearing with wheel speed sensor as well as all components necessary to access it.
  12. Lower vehicle.
  13. Unlock automatic adjuster in parking brake lever.
  14. Perform final adjustment of parking brake shoes

  15. Adjustment This vehicle is equipped with permanently sealed rear wheel bearings. There is no periodic lubrication or maintenance recommended for these units.


    Removal & Installation

    1. Raise and support vehicle.
    2. Remove wheel mounting nuts, then tire and wheel assembly.
    3. If equipped with AWD:
      1. Remove cotter pin, nut lock and spring washer from half shaft.
      2. While a helper applies brakes to keep hub from turning, remove hub nut and washer.
    4. Remove brake caliper and rotor from hub and bearing assembly.

      0996b43f807cb548.jpg

      Fig. Hub assembly

    5. Disconnect vehicle wiring harness connector at wheel speed sensor connector.
    6. Unclip wheel speed sensor connector from spare tire mounting support.
    7. Disconnect two sensor cable routing clips on rear suspension crossmember.
    8. Disconnect two sensor cable routing clips along toe link.
    9. Disconnect sensor cable from bracket on brake support.

      0996b43f807cb54d.jpg
    10. Completely loosen, but do not remove four bolts fastening hub and bearing in place. Once loosened from threads in hub and bearing, push bolts up against rear of hub and bearing to keep brake support plate in place when hub and bearing is removed.

      0996b43f807cb54e.jpg

      Fig. Rear hub and bearing mounting bolts

    11. Pull hub and bearing off knuckle and half shaft (if equipped with AWD), then thread wheel speed sensor cable through hole in brake support plate as it is removed with hub and bearing.
      0996b43f807cb54f.jpg
    To install:
    1. Position hub and bearing bolts though rear of knuckle and parking brake support just enough to hold support in place as hub and bearing is installed.
    2. Install hub and bearing by first feeding end of wheel speed sensor cable through hole in bottom of parking brake support. As this is being done, if equipped with AWD, slide hub and bearing onto half shaft. Place hub and bearing through brake support, onto knuckle, lining up mounting bolt holes with bolts and placing wheel speed sensor head at bottom.
    3. Install four bolts fastening hub and bearing in place. Tighten mounting bolts to 60 ft. lbs. (81 Nm).
    4. Place wheel speed sensor cable routing grommet into bracket on parking brake support.
    5. Route wheel speed sensor cable along toe link and rear suspension crossmember connecting routing clips where shown.
    1. Connect vehicle wiring harness to wheel speed sensor connector.
    2. Install brake rotor and caliper.
    3. If equipped with AWD:
      1. Install washer and hub nut on end of half shaft.
      2. While a helper applies brakes to keep hub from turning, tighten hub nut to 180 ft. lbs. (244 Nm).
      3. Install spring washer, nut lock and cotter pin on end of half shaft.
    4. Install tire and wheel assembly. Install and tighten wheel mounting nuts to 100 ft. lbs. (135 Nm).




May 18, 2011 | 2006 Chrysler Pacifica

1 Answer

Change rear wheel bearing is it hard to do ford fusion 03


Lightly losen the lug nuts with the tires on the the ground. Jack up the car and remove the tire according to the owner's manual. Make sure to block the wheels. After the tire is removed, release the park brake. Support the car on jack stands. Remove four bolts from the rear of hub. The hub nut will be 29 mm - it is important that you have a tight fit if you attempt to remove the nut.

At this point you MAY have to loosen or remove the remove the emergency brake cable. Either way the hub is ready to be removed. The front of the hub (with the lugs) and the bearing will come out and the back plate and brake shoes will remain in place.

Once you get it off, you may either purchase a hub assembly (which includes the hub with a new bearing in place ready-to-go) or take the existing hub and a replacement bearing to an auto machine shop which can easily remove the old bearing and install the new bearing. Using extreme care you can remove the old one using bearing pullers and prybars and replace the bearing using large deep sockets or a properly sized piece of steel pipe.

Since you have the hub apart, you should inspect the brake shoes and (brake) wheel cylinders and replace them as needed. Replace brake parts on both sides if you replace them on either.

Put the hub back into the brake shoes. It may only line up one way. Finger tighten ALL FOUR of the bolts and then tighten. Replace the tire and remove the lifting equipment. Start slowly so the brakes can readjust!

Sep 17, 2010 | 2004 Ford Focus

1 Answer

How do i change my rear hubs


Loosen the rear lug nuts, jack up the car, remove the rear wheels, remove the brake drums, remove the brake shoes and hardware, remove the 4 bolts holding the hubs in. Bolt in the new hubs, reassemble the brake shoes and hard ware, put the brake drums on, put the wheels on and snug the lug nuts, lower the car, tighten the lug nuts.

Apr 27, 2010 | 1996 Saturn SL

1 Answer

97silverado rear brakes i cant get the hub off to inspect the shoes


try hitting dreum with a hammer to free it of the hub a little penetrating oil will help.if the shoes are hanging you have to loosen them , there is an access hole in the backing plate you may have to knock the plug out then with a brake spoon back off the adjuster strut

Nov 09, 2009 | 2000 Chevrolet Silverado 1500

3 Answers

How to replace a transmission output seal 93 buick lesabre


you have to raise vechicle.use jack stands.block rear wheels.apply parking brake.when loosen axle nut.its more easier to leave wheel on.let vechicle weight hold wheel from turning while you loosen axle nut.you need to get a 1/2 break bar or large ratchett wrench with a deep socket .you need to buy socket use to remove axle nut a regular socket would probably break.when you remove the axle nut.remove brake caliper and brake pads.set them aside dont disconnect brake caliper.get a piece of wire to hang it out the way.dont use brake hose.could damage it. remove brake caliper support bracket then the rotor.get a hub removing tool remove hub.then loosen hub and bearings bolts .then remove shield hub and bearings assembly with O-ring.disconnect ball joint from steering knuckle using the proper tool.remove the halfshaft assembly and tap the seal from the steering knuckle.remove the steering knuckle from the hub.now that drive axle out the way.get the seal removing tool.its a flat tool with two hooks on it.to pry seal out transmission.or you can use a small chisel to clapse the seal but be careful dont damage the seal housing.when installing new seal coat it with transmission fluid.drive it in using a large socket.if you are reusing same axle replace circlip on the end of it.now putting back together.install a new hub and bearing seal in the steering knuckle with a seal installer tool .install steering knuckle to the strut.lubricate the hub and bearings with grease.install halfshaft.connect ball joint to the steering knuckle .install a new O-ring around the hub and bearing assembly.install hub and bearing assembly into the steering knuckle.tighten bolts to 75 ft lbs.install rotor then brake caliper support bracket bolts 120 to148 ft lbs.this is mounting bracket bolts only not the caliper bolts to brake shoes.put brake shoes and caliper back on torque 38 ft lbs.install shaft washer the axle nut to 180 ft lbs.tighten much as you can.before setting car on ground.to torque it to 180 ft lbs place car wheel back on set it down so the car weight keep wheel from turning.i hope this information works out for you good luck.and work safe.

Jun 27, 2009 | 1993 Buick LeSabre

2 Answers

Cant remove wheel hub


here is procedure

Section 04-01: Suspension and Wheel Hubs, Front 1996 Taurus, Sable Workshop Manual
REMOVAL AND INSTALLATION Wheel Hub Bolt Removal
  1. Raise vehicle on hoist.
  1. Remove wheel and tire assembly. Refer to Section 04-04 .
  1. Remove disc brake caliper (2B120), and front disc brake rotor (1125). Refer to Section 06-03 .
Brake Shoe and Lining Removal
  1. Remove brake master cylinder filler cap (2162). Check fluid level in brake master cylinder reservoir (2K478). Remove brake fluid until brake master cylinder reservoir is half full. Discard removed fluid.
  1. Raise vehicle on hoist. Refer to Section 00-02 .
  1. Remove wheel and tire assembly from front disc brake rotor mounting face. Use care to avoid damage or interference with disc brake caliper (2B120), front disc brake rotor shield (2K004) or front wheel knuckle (3K185).
  1. Remove rear brake pin retainers (2N386). ( I think it is a T 40 torx bit you need)
  1. NOTE: It is not necessary to disconnect hydraulic connections.

    Lift disc brake caliper from front disc brake caliper anchor plate (2B292) and front disc brake rotor (1125). Do not pry directly against metal caliper piston or damage will occur.
  1. Position disc brake caliper out of the way and support with wire to avoid damaging the disc brake caliper and front brake hose (2078).
  1. Remove outer brake shoe and lining (2001) assembly from front disc brake caliper anchor plate.
  1. Remove inner brake shoe and lining assembly.
  1. Position lug bolt (1107) to clear front wheel knuckle (3K185).
  1. Remove lug bolt from wheel hub (1104).



7548d8f.gif

Installation
  1. Install lug bolt into wheel hub.
  1. Using a lug nut (1012), seat wheel hub bolt into wheel hub.
  1. Install front disc brake rotor and disc brake caliper. Refer to Section 06-03 .
  1. Install wheel and tire assembly. Tighten lug nut to 115-142Nm (85-104 lb-ft).

May 25, 2009 | 1996 Mercury Sable

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...