Question about Cadillac Cars & Trucks

Open Question

How do you get the ignition lock out of a 1972 cadillac

Cant get the lock to release the lock cylinder

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 16 Answers

SOURCE: replace ignition lock cylinder 1996 BMW 318i with 1995 BMW

no you can not

Posted on Mar 12, 2009

jmgldsmth
  • 1869 Answers

SOURCE: Removal of 1998 toyota cressida ignition key cylinder.

This car has drillable shear pin screws on the bottom of the lock yoke you must drill these out.
then release the clip to the cylinder. you must get a new set of break-off shear pin head screws from the dealer to finish the job.

Posted on May 19, 2009

jimmy nutron
  • 132 Answers

SOURCE: i need to change my ignition lock cylinder but....

well is it that the key wont turn or dont have key? you can drill out the lock use a big bit it will distroy the tumblers so you can use a screw driver turn it and pull out

Posted on Jun 04, 2009

co7196
  • 3433 Answers

SOURCE: how do i fix the ignition switch cylinder on a

WEWhat is wrong with the cylinder. They are replaceable but not repairable. To just rempve the cylinder, insert the key and turn it backwards to accessory. The take a straightened paper clip ,insert it in the little hole in the plate the key inserts into anpush as you turn the key back to off position, Using the key to pull out the cylinder. Good Luck._Ned_

Posted on Oct 30, 2009

  • 85 Answers

SOURCE: how to replace a ignition lock cylinder for a 1999

youve been passlok screwed// patience and a lot of coffee its hard to explain this thing but with some staring and thought its not that hard also type in relearn procedure for this car in your browser make sure you typ every thing about it

Posted on Feb 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I know if my ignition switch is bad ?


The electrical part or the key lock cylinder part ?
Ignition Key Cannot Be Removed from the Ignition Lock Cylinder
Did you review the Steering Wheel and Column Description and Operation and perform the necessary inspections?
Go to Step 2
Go to Steering Wheel and Column Description and Operation

2

Verify the key cannot be removed from the ignition lock cylinder.
Is the key stuck in the lock cylinder?
Go to Step 3
System OK

3

Is the vehicle equipped with a manual transmission?
Go to Step 6
Go to Step 4

4

Turn the ignition key to the OFF position.
Can the key be turned to the OFF position and be removed?
Go to Step 6
Go to Step 5

5

Verify the adjustment of the automatic transmission cable. Refer to Shift Control Linkage Adjustment in Automatic Transmission - 5L40-E/5L50-E.
System OK
Go to Step 6
Ignition Can/Cannot Be Turned Off with Transmission in Any Gear
Operate the system.
Does the system operate normally?
Go to Testing for Intermittent Conditions and Poor Connections
Go to Step 2

2

  1. Push the ignition lock cylinder control actuator release button which is on the underside of the ignition key cylinder.
  2. Turn the key to the OFF position and remove the key.
Were you able to turn the key to the OFF position and remove the key?
Go to Step 3
Go to Lock System Does Not Lock

3
  1. Turn OFF the ignition.
  2. Disconnect the ignition lock cylinder control actuator.
  3. Turn ON the ignition, with the engine OFF.
  4. Connect a test lamp between the battery positive voltage circuit and the ignition key/shifter interlock switch supply voltage circuit of the ignition lock cylinder control actuator with a test lamp.
Does the test lamp illuminate?
Go to Step 8
Go to Step 4

Aug 20, 2015 | 2006 Cadillac CTS

1 Answer

2007 cadillac dts key stuck in ignition and wont shift out of park


Ignition Lock Cylinder Control Actuator
The vehicle it is equipped with a floor mounted console gear shifter, and has a ignition lock cylinder control actuator system in the steering column as an added safety feature. The ignition lock cylinder control actuator systems purpose is to prevent the steering wheel from being locked when the transmission is in gear and the vehicle may still be moving. The ignition lock cylinder control actuator system consists of the BCM, the lock cylinder relay, and the ignition lock cylinder control actuator. The ignition lock cylinder control actuator contains a pin that is spring loaded out to mechanically prevent the ignition key cylinder from being turned to the lock position when vehicle speed is above 5 mph for 15 seconds and the transmission is not in the Park position. If vehicle power is lost, and/or the transmission is not in the Park position the operator will not be able to turn the ignition key to the lock position and will not be able to remove the ignition key from the column. For situations where the vehicle must be towed, the system can be overridden by pressing a release button that is reached through an access hole located on the under side of the steering column. First, remove the black plug covering the hole.

Aug 09, 2015 | Cadillac Cars & Trucks

1 Answer

How do I replace a lock cylinder in a 1972 cadillac?


On the steering column, you turn the key to the on position and then push a wire into the pin hole to release it.
Should be a video on Youtube for early 1970s GM cars.

Feb 17, 2015 | Cars & Trucks

1 Answer

I cant get the ignition cylinder out of the bore,how do I get it to release


TURN IGNITION SWITCH IN START POSITION, INSERT A SMALL ALLEN WRENCH INTO THE HOLE IN THE TOP OF THE CASTING PRESS THE RELEASE PIN ROTATE THE KEY TO THE RUN POSITION AND PULL THE LOCK CYLINDER OUT.

Oct 05, 2011 | 2001 GMC Jimmy

1 Answer

How do I replace a ignition switch for a 1989 Cadillac deville


AutoZone Videos - Ignition Lock Cylinders

www.autozone.com/video/video.jsp?...Ignition+Lock...
AutoZoneFind Ignition Lock Cylinders videos at AutoZone.com. ... How to install an Ignition Lock Cylinder in a 95-2011 Ford. 14,972 views. Average rating of 4.4 out of ...

How to Remove and Replace an Ignition Lock Cylinder ...

? 5:13
https://www.youtube.com/watch?v=S9I4MnRIrHk
Sep 2, 2012 - Uploaded by RatchetsAnd Wrenches
How to remove and replace an Ignition Lock Cylinder on a 2003 Hyundai Elantra GT. If this video helped you ...

Aug 14, 2011 | 1989 Cadillac Sedan DeVille

2 Answers

Can not find the release spot for the ignition lock cylinder. I was told to try a safety pin, but cant figure how it fits in the equation. from what i can see the housing totally covers the ignition.


From what i gather you are trying ot remove the ignition cylinder fro mteh lock housing. If this is the case you will need to drill a small 3/16 hole into the ignition cylinder. then you will be able to depress the lock detention spring that holds the lock in the ignition cylinder. you should be able to get a free image of where to drill.

Jun 03, 2011 | 1984 BMW 7 Series

1 Answer

Auto theft system keeps coming on and disabling your ignition start.


the problem is probably the ignition lock cylinder. the ignition lock cylinder has two wires coming off it, after tine they will break. to repair need to replace the lock cylinder code the new lock cylinder and replace the key

Aug 26, 2010 | 1998 Cadillac Seville

1 Answer

I cant get key to go into ignition of my 2002 cadilac sedan deville


lock cylinder may have come apart on the inside, will need to replace lock cylinder and key

Aug 21, 2010 | Cadillac DeVille Cars & Trucks

2 Answers

How do you replace the ignition lock cylinder for a 1972 Corvette? The cylinder is stuck in the lock position and even with the key inserted it will not turn, thus locking the steering wheel and vehicle in...


Try and turn the wheel from side to side while turning the key as it may be jammed on the locking pin... If that's a no go then you must remove the steering wheel and signal switch to access the screw that holds the cylinder in place. If you must remove the wheel go to a parts store and buy a lock plate installer to remove the circlip that holds the lock plate compressed.

Jul 28, 2010 | 1972 Chevrolet Corvette

1 Answer

Location of ignition switch on 2006 gmc envoy


PATH: Chassis Electrical > Instruments & Switches > Ignition Switch > Removal & Installation Removal & Installation
  1. Disconnect the negative battery cable.
  2. Disable the airbag system, as outlined in the Chassis Electrical Section.
  3. Remove the hush and knee bolster.
  4. Remove the steering column trim covers.
  5. With the key installed, turn the key to the RUN position.
  6. Install a hex wrench into the hole on top of the lock cylinder housing. Push down on the hex wrench to release the tab on the lock cylinder inside the lock cylinder housing.
49901b3.gif
Push down on the hex wrench to release the tab on the lock cylinder inside the lock cylinder housing

  1. Slide the lock cylinder out of the lock cylinder housing.
  2. Disconnect the passlock and key buzzer from the lock cylinder housing.
  3. Insert into the lock cylinder housing
0bc8f9a.gif
Release the tabs on the ignition switch using ignition switch connector release tool J 42759

  1. Pull the ignition switch out of the lock cylinder housing.
  2. Disconnect the connector from the ignition switch.
To install:
  1. Verify the alignment of the gear in the ignition switch. If gear is not in position shown, turn gear in ignition switch until you reach the correct position.
  2. Use a screwdriver to rotate the lock cylinder housing gear counterclockwise until it hits a stop. In order to reach a stop while rotating the lock cylinder housing gear you MUST push and hold in the solenoid on the electric park lock.
  3. Connect the connector to the ignition switch.
  4. Insert the ignition switch into the lock cylinder housing. The tabs on the ignition switch MUST be seated inside the lock cylinder housing for proper installation.
  5. Use a screwdriver to rotate the lock cylinder housing gear clockwise to the start position—allowing it to spring return into the RUN position.
52c72cb.gif
Use a screwdriver to rotate the lock cylinder housing gear clockwise to the START position

  1. Align the lock cylinder and install the lock cylinder into the lock cylinder housing.
  2. Connect the passlock and key buzzer into the lock housing.
  3. Install the steering column trim covers.
  4. Install the hush and knee bolster.
  5. Enable the airbag system, as outlined in the Chassis Electrical Section.
  6. Connect the negative battery cable.

Oct 12, 2009 | 2006 GMC Envoy

Not finding what you are looking for?

Open Questions:

Cars & Trucks Logo

Related Topics:

171 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...