Question about Cars & Trucks

Open Question

2007 sr5 5.7 tundra serpentine belt diagram and how to

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 13 Answers

SOURCE: serpentine belt diagram:

if yours has the 3.8L then here is the diagram. Hope this helps
~ Zach

7f8b868.gif

Posted on Jun 16, 2008

  • 2 Answers

SOURCE: serpentine belt diagram:

The belt routing diagram is located on the top radiator cross member by the hood latch. You should see it when you open the hood. If it is not there, all Chrysler, Dodge, and Plymouth minivans, from 1993 to at least 1999, used the same 3.3L engine setup, so find someone with one and look for the diagram where I described.

Posted on Jul 18, 2008

abauto
  • 353 Answers

SOURCE: how do i change a serpentine belt for a 2007

Drive Belt: Service and Repair
DRIVE BELT

Components
43931e7.jpg


REMOVAL
1. REMOVE V-BANK COVER SUB-ASSEMBLY
2. REMOVE NO. 1 ENGINE UNDER COVER

4cff58f.jpg



3. REMOVE FAN AND GENERATOR V BELT
(a) While turning the belt tensioner counterclockwise, align the service hole for the belt tensioner and the belt tensioner fixing position, and
then insert a bar of [diameter]5 mm (0.197 in.) into the service hole to fix the belt tensioner in place.
HINT: The pulley bolt for the belt tensioner has a left-hand thread.
(b) Remove the V belt.



1. INSTALL FAN AND GENERATOR V BELT
(a) Set the V belt onto every part.
(b) While turning the belt tensioner counterclockwise, remove the pin.
NOTICE: Make sure that the V belt is properly set to each pulley.
(c) After installing the belt, check that it fits properly in the ribbed grooves.
HINT: Make sure to check by hand that the belt has not slipped out of the grooves on the bottom of the pulley.
2. INSTALL NO. 1 ENGINE UNDER COVER
3. INSTALL V-BANK COVER SUB-ASSEMBLY

c0b77ac.jpg

Posted on Sep 30, 2009

  • 538 Answers

SOURCE: 2007 chrysler sebring serpentine belt diagram

Go to; daycoproducts.com, click cars and trucks, then go to serpentine belt. Then on the right side of the screen click on finding your vehicle. Then get the illistration number and click on illistrations, go to that number it should something 6-? or 7-?. It's a pretty good websight.

Posted on Jan 31, 2010

c17hydro
  • 2984 Answers

SOURCE: belt routing diagram for serpentine belt on 2007

Accessory drive belt routing—1.8L engine



b98e301.gif

Posted on Aug 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace the alternator on a 2000 tundra 4.7L 4x2 non serpentine configuration


I presume the serpentine belt is in the way. First, disconnect the battery terminal. Then make sure the serpentine belt diagram is readable and remove the serpentine belt. Then release the tension on the alternator belt and remove all the bolts and wiring.

Nov 20, 2014 | 2000 Toyota Tundra

1 Answer

How to change Serp. Belt on 2007 Toyota tundra


The belt diagram is usually under the hood on the strut housing, on the radiator mount, or on the underside of the hood. They're sometimes inside the driver's door on the frame. The user's manual may also have the diagram.

Feb 22, 2011 | 2007 Toyota Tundra

1 Answer

2007 chrysler sebring serpentine belt diagram


Go to; daycoproducts.com, click cars and trucks, then go to serpentine belt. Then on the right side of the screen click on finding your vehicle. Then get the illistration number and click on illistrations, go to that number it should something 6-? or 7-?. It's a pretty good websight.

Jan 31, 2010 | 2007 Chrysler Sebring Sedan

1 Answer

How do you replace the serpentine belt on a 2007 toyota tundra 5.7


one of the idler pulleys is spring loaded ,look carefully to see what one it is then look to see if it has a square drive to put a rachet bar in to release the tension.

Jan 07, 2010 | 2000 Toyota Tundra

1 Answer

How to change serpentine belt, 2004 Toyota Tundra


locate tensioner pulley; release tension from belt; remove belt; make sure not to forget how the belt is routed; route belt around all pulleys but tensioner; put tension on tensioner pulley; route belt over tensioner pulley

Oct 03, 2009 | 2004 Toyota Tundra

1 Answer

How do i change a serpentine belt for a 2007


Drive Belt: Service and Repair
DRIVE BELT

Components
43931e7.jpg


REMOVAL
1. REMOVE V-BANK COVER SUB-ASSEMBLY
2. REMOVE NO. 1 ENGINE UNDER COVER

4cff58f.jpg



3. REMOVE FAN AND GENERATOR V BELT
(a) While turning the belt tensioner counterclockwise, align the service hole for the belt tensioner and the belt tensioner fixing position, and
then insert a bar of [diameter]5 mm (0.197 in.) into the service hole to fix the belt tensioner in place.
HINT: The pulley bolt for the belt tensioner has a left-hand thread.
(b) Remove the V belt.



1. INSTALL FAN AND GENERATOR V BELT
(a) Set the V belt onto every part.
(b) While turning the belt tensioner counterclockwise, remove the pin.
NOTICE: Make sure that the V belt is properly set to each pulley.
(c) After installing the belt, check that it fits properly in the ribbed grooves.
HINT: Make sure to check by hand that the belt has not slipped out of the grooves on the bottom of the pulley.
2. INSTALL NO. 1 ENGINE UNDER COVER
3. INSTALL V-BANK COVER SUB-ASSEMBLY

c0b77ac.jpg

Sep 28, 2009 | 2007 Toyota Tundra

1 Answer

Serpentine belt diagram 2007 dodge 5.9 3500


get the belt routing from the local dealer.
they will not charge alot of money for a reprint from the factory service manual.
also
dayco belts come with the belt routing on the box.

May 28, 2009 | 2007 Dodge Ram Truck

1 Answer

Chatter when turning


The serpentine belt should not have to be tightened because ther is a tensioner to keep it taught. If it feels loose then you need to check the tensioner and also see if the belt stretched. I hope this helps.

Jan 08, 2009 | 2007 Toyota Tundra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...